Ford Excursion :: Sputter At Low RPM Around 1500
Oct 20, 2015
I don't know if sputter is the right word, but at low RPM (around 1500) I hear this sound.
View 14 Replies
Oct 20, 2015
Advertisement
Ford Excursion :: 2001 V10 Cranks Fine But No Start / No Sputter
2001 Ex V-10 4x4. Ran like a top yesterday. Turns over fine but not even a sputter today. Plenty of fuel & battery. Has spark. Tried starting fluid, but nothing. No codes. Checked fuses and relays in dash & under hood. Fast forward an hour...
Went out and tried it again - fired up like nothing ever happened. Plowed snow for the better part of an hour, - ran like a champ again, smooth, no missing or stutters - parked it and shut it off. Tried to start it again within a minute or so and it would start, run rough & die. Tried a few more times with same results. Now it cranks fine but no start, no sputter. Gonna try a fuel filter tomorrow.
If it were the fuel pump, wouldn't it throw a code?
Ford Excursion :: Keeps Blowing Fuse 45 - Headlights Off - Engine Sputter And Die?
My Excursion keeps blowing fuse #45, a/k/a "Ignition switch Run/ Start feed"
Going to have to go in shop. Seems to be a short in the steering column.
Then the dash lights go dim, headlights die, engine sputters and dies. I am guessing alternator most likely.
These two things might be related? Maybe there's not a short in the steering column, I dunno.
Ford Excursion :: 2000 - Engine Cranks / Turns Then Sputter And Dies Suddenly?
I also tried jump starting - get same same result. Engine cranks, turns, and then sounds like it is just about to start up normally but it just dies completely. It seems to want to start but just can accelerate the engine high enough to keep it running. Almost like it's flooded on a carb motor.. 2000 V10..
View 7 RepliesFord Excursion :: 2000 - Hesitation / Surge And Stumble Over 1500 RPM
I recently picked up a 2000 Excursion with the 5.4 V8. Engine has 150,000. I got it cheap because it has a surging problem over 1500 RPM. This problem is intermittent.
I have 1 DTC. P1000 which is OBDII checks not complete. I cannot clear this even using the factory procedures. FYI..I have a snap on solus scanner. I think this is a voltage problem, If you try to start the engine with the scanner plugged in, the scanner shuts off, so I'm thinking the PCM loses battery power supply when the starter engages, resetting the PCM.
This problem is NOT a miss.... something isn't opening or shutting off above 1500 RPM. This truck doesn't have an EGR system, it has the EVAP system. This may be the problem, thats why I'm here. OK. heres a list of what I've replaced since I started working on it.
Engine oil and filter
air filter
fuel filter
8 COP's
8 plugs gapped properly
cam position sensor
IAC sensor
MAF sensor
Removed throttle body and cleaned.
Vacuum checks. 22" at purge valve,fuel dia, and vacuum canister
Checking with the scanner at 1500 RPM with problem
SFtrim1% bounces between5-15
SFtrim2% bounces between2-0
LFtrim1% bounces between11-13
LFtrim2% bounces between 5-6
O2S11(mv) bounces between 200-781
O2S21(mv) bounces between 200-800
Ssystem is in closed loop holding throttle at 1500 RPM... Note engine surges when at the RPM or above. I'm thinking the engine is lean, not sure how to read the trim numbers...
Idle is fine ... Problem is intermittent ... Also noticed that engine will only advance spark to 30 degrees @2000 RPM during this problem. I have seen it advance to 38-40 degrees when I do not have this problem, so I kind of understand the power loss,knock etc due to the timing, my question is whats causing it to do this?
EVAP question.... The purge valve should open according to PCM command a certain value, correct? I can monitor the duty cycle % but cannot activate and check proper duty cycle through scanner . When I try to I get an error message of module error -unspecified.
Disconnected hoses at purge valve,Full manifold vacumn on one, nothing on other, no flow through purge valve, but scanner shows 30% duty cycle. I would think the should be a little flow at 30% Maybe my problem? Troubleshoot procedure for the EVAP would be good.
Ford Excursion :: 2001 V10 - Ticking Noise At 1500 RPMs
I have a 2001 v10 with about 157k miles on it. Recently (within last 2 months) I am getting a ticking noise that is pretty constant. It doesn't seem to increase with rpms and I can barely hear it with the hood open- I hear it much better with the hood closed. It seems to start about 2-3 seconds after I start the car (when fan clutch engages?) and seems to be coming from the front middle of the engine. I do not see any broken exhaust studs. I do also occasionally have a ticking noise at 1500 rpms (only at 1500 rpms- not sure if it's related or not). I made a short video- not sure if you can hear the noise.
View 8 RepliesFord Ranger / B-Series :: 2003 - Sputter And Jerk Just For A Second
I have a 2003 ranger with 2.3. I drive it daily but it has started to sputter and jerk. The truck has 94000 on it and I bought it new. It sat for over a year but has been driven every day for the last year. It started a couple months ago but would just do it for a second, now I cant drive it on the highway. I think it might be injectors but how do I know for sure?
View 12 RepliesFord - Explorer :: 1998 - Turn Over / Sputter And Die But Will Not Start When Hot
1998 explore will not start when hot will turn over sputter and die, after 15 minutes it will start right up that was last monday when it was 80 outside it now colder outside has not done it again, the only thing i have seen that temp gauge is not going past cold never getting to center it will try and drop back down...
View 11 RepliesFord Escape / Hybrid :: 2002 4WD - Engine Sputter When Accelerating
My daughter has a 2002 Escape 4WD with 3.0L engine.
Coming home from school a few weeks ago she experienced engine running rough on the highway when trying to accelerate. We ran the diagnostic on it and it revealed that #2 cyl coil was misfiring.
I've replaced all of the rear bank coils (in hopes that I wouldn't have to remove the intake manifold again anytime soon). I also replaced the connectors and weatherproofed them.
Replaced all the plugs while I had easy access too. This all went pretty smooth with exception of breaking 3 of the 5mm coil bolts off inside the valve cover. I've also replaced the upper and lower intake manifold gaskets.
It runs much better now except now on the highway, at 1800 rpm/55 mph if I try a gradual acceleration I get engine sputtering and it won't accelerate. If I push hard on the pedal it will downshift and accelerate normally right past this trouble spot. Other than this it idles and runs great.
I've noticed that the 3/4 in. vac hose on back of manifold is getting pinched closed about 70%. this is the hose that leads down to the top of engine just below lower manifold. I suspect this is the problem but cannot determine the root cause. I assumed it was the intake manifold gaskets but those are now replaced.
Ford - Focus :: Sputter And Die When Running On Idle For A Few Minutes / Cannot Turn Left
I drive a 2007 Ford Focus and when the fuel level gets to half a tank the car tries to die, and quite often does, when making a left turn. About 1% of the time it will do it when making a right hand turn. It will also sputter and die when running it on idle for a few min. It first started doign this at 1/4 tank but has gotten to where it will do it at 1/2 now.
View 8 RepliesFord Fuel System :: 1978 F250 - Truck Will Sputter And Just About Die When First Let Off The Clutch
i have a 78' F-250 4x4 4 speed with a straight 6. it has headers and an eldebrock 600 on an offenhouser dual plane intake. The carb just randomly started acting up the other day and what to try now. it will sputter and just about die when i first let off the clutch then it will suddenly start racin. its really annoying and hard to drive. i checked the inline fuel filter and it should be getting plenty of gas. didn't find any vacuum leaks.
View 14 RepliesFord 6.7L Power Stroke Diesel :: Sputter / Shutter Sound Coming From Around The Air Box
I have a 2012 Ford F250 6.7 powerstroke. Truck has about 30,000 miles. Has been completely flawless and has exceeded all expectations. Well....I am experiencing my first hiccup.
I traveled yesterday. While going up a slight grade, running about 50 mph, 1000 RPM, 10PSI boost...truck started bucking and sputtering with weird sound coming from around the air box. It felt just like you had a blow out on the front right tire. My initial thought was i just had a blow out as the truck hopping. Well, once i let off the throttle everything went back to normal. It did this about 5-6 more times on the trip. When it would start doing this I would just let off the throttle and everything would go back to normal.
I've read a good a bit on this 6.7 and appears that turbo issues are common. Being optimistic, I am hoping this is something that can be fixed easily. Again, have had ZERO problems with this truck, runs great, and even now on the trip runs fine but now we have this intermittent issue that I do not like. I am very diligent in taking care of my equipment, have not abused this truck and all maintenance is current (actually a bit over kill). What the issue could be.
Ford Ranger / B-Series :: Random Sputter At Idle And Misses Around 4k When Get Into Throttle
I have a 2000 3.0l ranger. I have been battling an ignition problem. every time the engine is cold it runs terrible like only 3 or 4 cylinders running terrible. if u put a timing light on the wires the pulse comes and goes on random wires. and when it quits that it has a random sputter at idle and misses around 4k when u get into the throttle ...
I have replaced plugs twice and the coil with motorcraft parts and the wires are new autolites. I have also replaced the thermostat and fan clutch it was getting hot in the middle of this other issue ...
Every time I replace something it runs great for a few days then back to running terrible again. am I missing something else do I need to look at a computer or map or tps sensors, or something like that ...
Ford - Explorer :: 2003 - Sputter - Got Codes P2196 And P0405 - O2 Sensor?
I have a 2003 Explorer 4.6, about 2 weeks ago the CEL kicked on but I didn't notice any problem. Last week I stopped at a red light and felt it shacking a little, I took off everything seem ok. At the next light I felt it again and that time it started sputtering, I drove it for a few more days and it would sputter now and then as I was driving and every time when I would stop when it was in drive. I had the codes pulled and it came back with P2196 & P0405 (o2 & EGR).
I was going to buy a new 02 sensor & EGR but I was told that a bad EGR could be causing the o2 code also. I put the new EGR on yesterday and had the codes cleared. I test drove it for about 10 miles with no problems. Today while driving I felt it start doing it again and about 5 mins. later the CEL was back on. I got the codes and again its P2196 & P0405, Should I have changed the 02 sensor instead or what I should do next?
Ford 7.3L Power Stroke (1999-2003) :: Crank But Will Not Start / Sputter And Smoke
I have a 99 F3 50 with the 7.3 L I am done a lot of work to replace the HPOP pump and the ICP sensor as well as the IPR it cranks but does not start it will sputter and smokes but doesn't run SOS. Also there are no dtc in computer....
View 8 RepliesFord Super Duty (1999-2016) :: 2002 - Start To Sputter Intermittently?
I have a 2002 F250 superduty with a 5.4 in it, every once in awhile it starts to sputter. Its usually when i'm easing on the gas, possibly around a certain rpm and completely random. Once it starts i can get on the gas a little and it stops. i've changed to fuel filter and air filter recently so i know its not that.
View 2 RepliesFord 6.0L Power Stroke Diesel :: 2003 F350 Stall / Sputter Now No Start
Its a 2003 f-350 6.0 started out just stalling out throw it in N it would fire right back up then started to sputter now I have a no start doesn't even try to start no smoke on crank. all of this between -3 and 5 degrees outside. According to my scan gauge ipr is 14.8, have ficm sync, ficm main is between 47 and 48 cranking, builds 0 icp irp duty cycle doesn't go up either. Pretty sure my icp is bad leaks oil though the sensor and pig tail is covered in oil. Truck has 197000 miles hpop, injectors, and ficm changed around 165000 oil cooler and blue spring at 1800000...
View 13 RepliesFord Ranger / B-Series :: 1999 - Truck Will Miss / Sputter And Buck Randomly
1999 Ranger 4.0. I have an issue with my ranger. Sometimes the truck runs awesome.While driving along the truck will miss and sputter and buck, when this happens, I almost can't maintain my speed. Sometimes when this happens if I put the truck in neutral and shut it off and restart it. The problem will temporarily go away. Occasionally it will go away on its own. When it goes away on its own it's like someone flipped a switch and all power is returned and running smooth. When the truck is at idle it depends on the mood of the truck, sometimes it's fine and other times it wants to die. I got to make this truck last awhile longer.
View 7 RepliesFord F-150 - 1997-2003 :: 2002 - A/C Causes Rough Idle And Stall / Sputter And Die On Restart
I have a 2002 4.6L FX4. When I run the A/C for an extended period (say 15-20+ minutes), it will start to cough and sputter and eventually just die. It will restart but run rough and cough, sputter, die.
If I turn off A/C and let it set a while, it runs fine. No check engine light. Possible EGR problem????
Ford 6.0L Power Stroke Diesel :: 2003 F250 Won't Stay Running / Sputter And Died
My 2003 F250 started to sputter and died. Won't restart the rest of thw day. Go out next morning will start right up for about 1-2 min and dies like you shut thw key off. Won't restart. Cranks fine.
Oil pressure showing 1300lbs while cranking,ipr is 43% while cranking, but when koeo ipr is 97% which is weird. My excision shows 23% koeo.New oil,oem filters,fuel pressure is at 50 lbs while cranking. Seems electrical or something. Oil pump maybe but why 1300 lbs while cranking of that?
Ford F-150 (2004-2008) :: 2005 - Truck Starts To Sputter And Kick A Bit When Driving At Low Acceleration
I have a new to me 2005 F150 with 86,000 miles. When I am driving through town at a low acceleration or a constant speed at between 40 - 50 mph the truck starts to sputter and kick a bit. When I give it some gas the problem goes away. This gets worse when I pull my bass boat, and starts at around 30 mph. When I hook it up to a reader I get a P0316 code. Only code I get.
Also when I am driving through my neighborhood between 20 - 30 mph I get a noise that sounds like there is a plastic bag stuck under the truck. I have checked under the truck to see if the firewall is loose anywhere, but could not find anything. Other than those two issues the truck runs great. What these problems could be?