With normal acceleration my ex up shifts at about 50-55 mph and makes a shuttering noise and has a slight vibration briefly during the up shift. Could a tranny fluid change work?
View 14 RepliesI have had a minor vibration above 50 or so mph(by speedometer). Installed a new driveshaft and corrected the pinion angle to near perfect. I have OEM 4.30 gears and 33.4" tall tires. I had to retune motor/PCM and one of the options while installing the new tune was tire revs per mile.
I input 620 and pressed on. Now my slight vibration is gone. Even at a corrected 70 mph it's smooth. I'm a little baffled, as I do not understand how a tire diameter correction in the PCM could affect the drivetrain?
I'm looking at a 2001 Excursion with 242k miles. Truck is all stock, and everything checks out well. The only thing is there is a slight vibration at idle, that increases quite a bit when the engine is revved to about 12-1500rpm. Ran a CCT, and #8 was flagged. I know that can be somewhat normal depending on the CPS, right? Otherwise the truck is smooth, and in great shape. Should I be concerned about what feels like a slight miss on #8?
View 3 RepliesOk, my 2003 Ex Limited with 109,000 started doing the same thing today that it has done many times before. It started shuttering and then stalled. It comes out of nowhere and then the overdrive light flashes at the same time. I have had the coil packs replaced in the past, but not all of them at once. I also had the torque converter replaced last year as well. I am pretty sure that it's more coil packs that need to be replaced again. I'm sick and tired of replacing coil packs on this truck, it seems like they go bad very quickly. It's so bad I'm thinking about getting rid of this truck and getting something different.
View 14 RepliesI am experiencing a slight rumble-strip-like vibration/noise when veering to the right. There is no noticeable vibration when driving straight or to the right - sounds like it's coming from the front. I thought it was my tires but had them rotated with same symptoms/ I first noticed this shortly after I had them rotated in July. So it's probably front suspension.
View 3 RepliesI have a 2010 Explorer XLT that I bought in 8/2012 with 7,000 miles on it. I had had a problem with a groaning noise and slight vibration starting at 34 mph, under load. I don't hear the noise if I let off the gas at 34. I hear it a little past 35 or so and it doesn't seem to groan again until about 60 mph or so. I also have a feeling of the all wheel drive engaging when I back out of the driveway, put it in drive and turn the wheel slightly.
I took it to the dealer this week under warranty and he calls me today and says the tires are worn differently all around and that is causing the problem. He says the tires could be out as much as, or as little as 1/16 of an inch and that is what is causing the all wheel drive to catch and also the groaning noise. I understand what he is saying, but I can't believe that is the problem or more would have been written about it.
I asked the guys about rotating the tires and he said it would not matter, it would just take the problem from one end of the vehicle to the other. These tires are not worn like the truck is out of alignment, it is just normal wear. It now has about 21k on the odometer. What do you all think of this diagnoses? The guy says the PTU thinks it needs the all wheel drive and therefore engages it. This truck can also be manually put in 4 wheel drive by flipping the switch.
Recently I have a vibration that I can feel slightly through the steering wheel. If I'm driving down the highway doing 70mph + I have a noise coming from the front end. Also while driving let's say 40mph and below and I let off the pedal to slow down I can here a vibration in the front that kind of sounds like a small Jake break. And when going over anything bumpy I hear like a popping metal sound. This popping sound has been going on for a long time and still can't figure it out. I replaced all my shocks thinking my old set was bottoming out. Nope, still have the same problem.
I jacked up the front end yesterday and checked for movement top and bottom and side to side thinking maybe the wheel bearings or ball joints were going. Everything is solid. Spun the wheels and no noise, no grinding, nothing. I can't figure it out. I have not removed the wheels to check and see if a caliper is loose. I will be checking that next. I did notice while looking around that I can push up on my pitman arm on the steering box. It's not a huge amount of movement but I can still move it. I can also see teeth marks between the box and the arm, not sure if that is normal or not. When I do move it up and down it sounds a lot like that metal popping sound I have been hearing. So, I know this is a lot.
2001 F250 7.3L 280k miles. Truck is new to me in the last 6 weeks. Was driving out to Glenwood Springs last night and I got a weird rear end vibration between 79 and 81 mph - couldn't say if it's a new vibration as haven't had the truck long enough. It's sort of still there over 81 but less obvious than bang on 80. Whilst the vibration was there I caught a slight dip in the road that caused a grinding noise to accompany the vibration - I'm guessing because something's was getting extra loading on the upside of the dip.
I'm away from home until Monday so my options are a bit limited, however while crawling around in the dark last night pushing and shoving stuff to see if anything was loose I noticed a couple of things:
Minor leak from pinion seal - but it has flung some spots of oil. Drive shaft 'center bearing'(? U shaped attachment on drive shaft to chassis with rubber bearing?) has play I can push the drive shaft at least a 1/4" with my hand and it seems a little sloppy but I'm no mechanic.
I'm going to check transmission fluid level today and top up if required and check the magnets, such that I can limp home as necessary avoiding 80 and get the diff checked and pinion seal replaced. Does the drive shaft bearing need changing or should it have that much play? I'm assuming it's LSD on the rear?
2002 Ford F250 4x4 Superduty Lariat (4 door). Just changed the locking hubs to a new set of Warn manuals. I began to periodically hear what sounds like a rumbling/bearingish/howling kinda sound. Happens when you hit a bump at any speed...then howls till you hit another bump..goes away..then process repeats. Come to a complete stop, and the sound usually goes away till you hit another bump. The hubs are "free" at this time.
Heres the weird thing...when the noise starts...I switch it into 4 wheel drive on the dash...the sound instantly goes away. Click it back outta 4 wheel drive (hubs are still unlocked this whole time) and the sound is gone. drive some more down the road, maybe hit a slight bump, and the sound returns. Switch it back into 4x4...sound instantly goes away. Its not really in 4 wheel drive, cause the hubs aren't locked in...but that cures it till I take it back out. What could be causing this howling ? Its getting worse, and you can feel a slight vibration in the floor now when its doing it.
I've recently been hearing a grinding/vibration noise on takeoff. I only hear it pretty much as soon as my foot comes off the brake, when the car is in drive, and the car gets its first bit of forward engagement/movement. It seems to only happen when the DSG engages in drive, before I put my foot on the gas pedal.
The closest thing I can say it sounds like is an exhaust rattle, but way less violent/not metal on metal sounding.
I know it's stupid but rattles and vibrations in an otherwise quiet car drive me absolutely crazy.
So, driving I have noticed this slight non-metallic vibration type noise. It seemed to come and go. So I emptied the car thinking it might be something I was carrying around. No such luck. Turned off the climate control, still there. I had the better half drive while I searched. I could never really see anything but thought it sounded like it might be either in the dash or around the floor area. Totally frustrated I unbuckle my seatbelt and crawl into the passenger floor head first. Nothing on the passenger side. I glance over to the Driver side footwell and notice the slightest vibration from a panel that covers the steering shaft as it goes through the firewall right behind the pedals. Aha! A plastic panel being held in place by 2 plastic type screws that are both loose. i tighten them down with a straight screw driver when I get home and silence! The rattle goes away. You might look at yours as well. I think this might apply to all Mk5 cars. Finding/Fixing a rattle like this for me is like finding money.
I have been experiencing a slight wheel vibration from the rear of my R32? I am thinking about replacing my wheels and tires, (continental sport contact 2 is what I have now) I have heard that the continental tire has an aggressive tread pattern because i get a tire noise above 45 mph.
View 12 RepliesComing back from PA yesterday after snowboarding noticed a vibration and a small amount of noise coming from the back of the EX once I got back into town. The vibration is def speed related and completely linear with how fast I am going, the noise for lack of a better description is like a low roar. Starts to be really noticeable coasting to a stop around 45 mph down to 0.
Only does it coasting, not under power, as soon as I pick up the throttle again it instantly goes away. Might open up the rear dif to see if there are any missing teeth or metal shavings if I can find time. Hoping its a Ujoint, cant afford to do a gear swap right now and I need my EX...
Starts getting loud above 35mph, local tire shop recommends replacing the struts- says they are causing bumps in the tire because the tire is bouncing along as I drive. I did feel bumps going across the tire when I passed my hand across it.
View 15 RepliesHere's the deal:
1. My 2002 SC430 with 23,000 miles on it is making a low rubbing noise when slowing down, with a slight vibration, not severe enough, but it is annoying and frankly surprising on this car. The dealer tells me it's because the brakes have "glaze" on them, and short of a new brake job, you can jam on the brakes to clear or loosen some of this and reduce the noise. ( I live in the desert so I'm sure I could find a deserted stretch or road for this craziness...) The dealer reports the brakes have 70 - 80 percent life on them and I don't need a brake job.
2. Power steering. I thought this particular car was just hard to steer, but even the tech at the dealer commented it's like I have no power steering. I test drove two other cars, and the steering is markedly lighter on the other two SC430's I drove. (2002 and 2005) Dealer can't seem to find an explanation, but I have to drive this car with two hands around town... I know this is not the way this car was intended to feel.
I don't believe the car changed that much from the 2002 model so as to affect the steering. BTW, I'm using stock tires, not run flat, 4 months old. And the steering is stiff at idle anyway, regardless of tires. The first SC I drove, which sealed the decision to buy one, was so quiet I didn't know the engine was running, easy to steer, and smooth.
Ok...not sure were to go with this or how to explain it, while climbing a steep paved hill at 5-10 mph I get a rumbling vibration and noise. If I were to guess almost like axle wrap is causing the U Joints to bind or something. Runs and drives fine other then that. If I put it in 4x4 it does not happen, only seems to happen when wheels cant slip while climbing hills at LOW speed.
Don't notice it if climbing a dirt hill. There is a hill at the kids baseball fields that is steep and paved that its really bad on, way to busy right now to play on it to see what's happening. Tranny was looked at and oil changed.
New BDS 4" lift - had same issue prior to lift, though stock springs were worn.
Searched the form but really didn't come up with anything at this low of speed. While in Wisconsin the resort we were at the paved hills were so steep it felt like something was going to break. Put it in 4x4 and it was fine. This was with stock leafs.
my car is FORD C.V. at 50+ mile/h. starts slight vibrating. did alignment and leaded front tires, but no success.
View 3 RepliesI haven't really gotten under it to check this out, but my truck (see signature) has a slight vibration on take off. It only does it when the wheels are turned to the right or left. They don't have to be turned very far either. It doesn't do it on straight line take offs, or on a take off from a rolling stop. ONLY when pulling off from a dead stop and the front wheels are turned any degree to the right or left. I'm running mostly bald all terrain tires, the wheels are not bent. My current wheels are new to the truck, and the problem was there with the previous rim/tire combination. The rear end doesn't seem to have any slack in it. The transmission shifts like a top. There are no other clanks or vibrations anywhere in the drivetrain and it drives good.
View 9 RepliesAbout 2 yrs ago there was a slight vibration in the car, it would happen every couple of months and last for about 5 seconds. It has gotten progressively worse and now happens quite often. There is no pattern as to when it will happen, when I first start the car, in park, neutral or driving. The vibration is the same at hwy speeds as it is at idle. I only have 111,000 miles on the car. I have been told it's anything from the torque convertor/transmission to the IMRC.
View 4 RepliesJust bought my 2013 Ford F150 Supercrew 4x4 on Saturday. I noticed a vibration at 35 to 45 mph. Its a slight vibration, the whole truck kind of shakes. Really annoying for a truck with less than 200 miles.
View 14 RepliesI bought this Ex a little over a month ago and finally got around to replacing some stuff.
I have a slight vibration between 50 and 60 MPH. The vibration is the same weather I am accelerating, in Neutral, Coasting down (well, a little bit worse when coasting down), in 2WD, in 4WD, turning, going straight, hot or cold.
I have replaced the following:
Rear Driveshaft U-Joints
Tires and Rims
Upper and Lower Ball Joints
Wheel Bearings
Steering Stabilizer
Cleaned and Greased the Hubs
Greased everything greasable up front
I still have the exact same vibration as when I started. I can feel the vibration in the steering wheel as well as in the body of the vehicle. I am thinking that it may be in the steering linkage. If there is a loose joint then the wheels would be allowed to jiggle a little bit. I am at a loss. What else should I check?
Also, When doing the ball joints, I noticed that the tie rod ends were quite stiff. How stiff should these be? I can't move them by hand, but they will move a little bit when moving the free end of the tie rod.
I am taking it in for an alignment on Friday, and if I can't figure this vibration out, I might have them take a quick look into it. Would a stuck slide pin in the front brakes do this? Both sides on my truck are seized at the current moment.