Ford Excursion :: SES And ABS Lights On - Code PO500
Nov 5, 2012
So I am starting down my long list of repairs needed on my new to me ex. I have a SES light on and a ABS light. Went into Advance to have them check the code. Came up with PO500. Did a search here and found out that it is the vehicle speed sensor. Probably explains my intermittent loss of speedometer. Did another search to find out where this sensor is and can't find anything. Where it might be? It is a 2000 Limited v10 4x4....
View 9 Replies
Advertisement
I am looking for the part number for the ABS speed sensor mounted on the rear differential for my 2000 Ranger XL 4x4 3.0 flex fuel model. I am also looking for the name of the part so I can look it up on the ford parts site. while looking I have found these names ABS speed sensor
Powertrain Control Module Speed Control Sensor
I had my truck in the shop and they did a health check, they found these codes po500 - cluster fault and the abs module fault
View 5 Replies
I have a 2001 Excursion, 6.8 V10, with the factory fog lights.
The fog lights worked fine, until a few days ago until they suddenly stopped working when just the parking lights are on.
I can still pull out the switch, the indicator light does not come on but the parking lights still work. When I turn it to the headlight position with the switch pulled out everything comes on and works like it should.
I tried checking the fuses but I didn't see one labeled in the manual for the fog lights so I don't know for sure which one to check. Could I possibly have a bad switch?
View 6 Replies
Okay I bought this 2005 Excursion with a V-10 in it. Got it home and the CEL came on. PO303, @ first 1000 rev. Okay so I changed all the spark plugs, swapped the number 1 and number 3 coils, same code, and as a last resort changed the injector also. Ran it 65 miles bam lights back on. Same code I'm at a lost of what to do. What are my next steps to take to fix this?
View 14 Replies
I have suddenly acquired a new value added feature to my X. An airbag warning light flashing code 18. Through the research I have found it is either a pretensioner issue or a short. Would like to know for sure what it is.
It is a 2001 LTD 5.4L.
View 5 Replies
I have searched and found a few threads of folks getting a p0720 code and truck revving and dying. Just wondering how to resolve the issue and what the cause was. I have an 01 ex with v-10
View 13 Replies
Doing led light bar in place of the fog lights? I was thinking of doing it or possibly adding led light blocks, something like this. I saw this truck on CL and really like the look of the blocks....
View 13 Replies
I have an 03 X with 225k on it. I put 8 new injectors in it because I was leaking fuel into the engine oil. I got them from dieselogic from ebay in Jacksonville FL. 4 of those were leaking and they warrantied them. Then 2 of them were getting contribution codes and they would not warranty them because they said I had fuel contamination. They did not send them back to me either. I got 2 more from advance auto parts. They were working fine. For a little while. So now here is where the problem is. I was getting a cylinder 1 contribution code. So I swapped cylinder 1 and cylinder 3 injectors. That code is gone now.
Now I have cylinder 4 contribution code. I swapped 4 and 6. Still have cylinder 4 code. When the engine is cold it runs perfect. When I drive it for about a mile or so and come to a stop sign it's still running perfectly. While I'm at the stop sign it's like someone flipping a switch and then the misfiring starts. And no codes until the "switch" is flipped. Ficm measures 48 to 48.5 at all times. I don't see any chafing of wires. And I forgot to mention that I had a leaking fuel into the oil again. Ran another dye test but did not see any signs of leaks this time. But that was after I swapped injectors around. Could have been leaking from the orings. I can't can't figure out this misfire. So I was thinking compression test next but why does it run fine when cold?
View 1 Replies
Last time I filled up was Friday and the gas gauge hasn't moved. When I shut the Ex off it goes back to the bottom so I know the needle isn't stuck. I'm also getting a code u1262 from the instrument cluster that wasn't there last time I checked so I'm assume it's related. Where to start troubleshooting?
View 6 Replies
2005 Excusrion V10 6.8L .. Have the PO720 code ..
Replaced alternator it was bad when tested
Replaced OSS - the voltage on this when running varies in the 1.3 - 1.7 range.
What should the ohm voltage read? What would you try next?
View 4 Replies
I am getting an error code of 1201. Is this the ERG valve? How do I change out? Looking for Pictures or diagram?
View 5 Replies
My 10 year old Halogen lights are failing. Trying out LED light strips like the "Kawell - Slim 18w Flood Beam LED Work Light" for auxiliary backup lights?
View 14 Replies
Is there a way to turn off the fog light's on a 2000 xlt
View 9 Replies
I changed the bulbs in my fog lights as the older ones were very dim. Went to fire them up and nothing. tracked down the fuse under the steering wheel (43 I believe) and it was blown. replaced the fuse, still no fog lights. Checked new fuse, and it is fine. changed it with a different one (you never know) and still no fog lights. Is there a separate fuse/relay somewhere else that I may be missing?
View 6 Replies
What would cause the running lights to not turn off? The door ajar light is not lighting up so would it be safe to assume that it isn't a door ajar problem? The interior lights are on as well but I have already done the interior light switch mod and changed them to LEDS so my battery draw will be a lot less. The running board lights do turn off after about 45 minutes though.
My overhead console backlights do not turn on and the rearview mirror isn't lit either since last week but I do not know if the issues are related. The Lie O meter still works fine though. What fuse it is? I would like to pull it till I get this resolved.
View 7 Replies
Wife got home from work the other day with no problems and then a couple hours later tried to go start excursion to leave and battery was dead. I tried jumping it only to find out that once the battery started getting juice in it the gauge warning lights started to illuminate. Wouldn't start with being jumped so put the battery on charge for a couple hours and still no go. Took the battery into napa and they tested it and said it was bad.
Put new battery into it and am still stuck with the same problems. Hook the battery up and no key in the ignition and the warning lights around the exterior of the gauges are lit up. This is all on a 2000 v10 excursion. Up until now we have not had any problems with this truck. Wife daily drives it with no problems.
View 14 Replies
I have a 2000 ex 7.3 and a couple of days ago I had the batteries die on me. Quick boost and it fired right up, drove it around for the rest of the day no issues at all. Yesterday I had a really hard time with the first start of the day, turned over slowly, but caught itself and fired up. I plugged in my OBDII adapter and fired up Torque on my phone and saw that I had 14.3 V about 30 seconds after the truck started. Took my father to pick up his car about 10 mins away, shut the truck off, and again, it turned over slow, was a hard start.
Drove it around for about 45 mins after that and everything seemed great. Today it won't even start...the WTS light comes on, everything sounds and seems normal, then when I go to start the truck it just "clicks"...Turn the headlights on and try to start it, and the lights don't even dim. So I checked and cleaned the battery cables and the starter cable...still no start. What it might be? I'm hoping that its a ground somewhere but wouldn't know where to being looking..
View 14 Replies
2 weeks ago the running board lights stayed on for like 5 mins until I went out and messed around with this and that. Tonight I came home and all three brake lights will not shut off. Tried driving,flipping switches....
View 10 Replies
I need a tutorial as to how to get to the dash lights in an 04 Excursion.
View 1 Replies
Factory fog lights worked fine, had body off for the head studs recently, they worked fine after. One day they just don't work. Fog light indicator light still comes on. Fuse is good. High beam indicator still works. Where to troubleshoot next?
View 6 Replies
Was about to buy a headlight switch with the Foglights option...realized I miss the auto lamps.
Is there a write-up on how to add these? Looked in the tech folder and didn't see one
What parts are needed?
View 6 Replies
