I've noticed quite a few threads looking for the shock bolts lately. I've replaced one of mine and just had another break. Today I ordered replacements for all 4 nuts and bolts.
The Bolt part number is - N605906-S2
The Nut Part Number is - N803714-S426
I need to identify the part numbers for the u joints in the rear drive shaft. The guys at the auto parts store kept telling me I only need two until I showed them that there are clearly three. I just want make sure that I get the correct parts before purchase.
View 5 RepliesI need a new upper driver side door seal and the plastic driver side fog light bracket but can find part numbers for my 2005 Ex.
View 3 RepliesI need to replace the bearing on my Idler pulleys, both smooth and grooved. I also want to replace the bearing on the tensioner pulley. What are the part numbers and the best place to order them from?
View 10 RepliesMy recently installed Monroe Quick Struts are not dropping to the stock height, I thought I'd retrofit OEM springs.
I find that it's not easy to figure out what is the correct part. Various sites show differences in Japan vs US build, some show different parts for left and right and there's no particular consistency.
So, what are exact part numbers? This is a US built 2005 LE AT. The build date is 04/05.
Looking for info about some part numbers? I'm looking for the silver aluminum trim on the driver inside door. Where you rest your left arm. Also the driver black air vent assy all the way on the left where the headlight switch goes.
View 7 RepliesLooking to install rear sway bar on 2001 Ex. and noticed a skid plate looking thing in front of passenger side rear shock. Two questions:
1. What is that, and
2. Do I need to remove it to put on sway Bar?
When I bought my truck one side of my truck had plastic between the outer sheet metal and inner sheet metal and the other side was missing. It looks like the purpose is to keep mud and road gunk from shooting up into the rear area. Where I can order replacements and what they are called? I need both sides, since the one I did have was cracked and barely hanging on.
View 8 RepliesAny trick that they have used before for removing the Front Passenger Shock Top Nut without removing the A/C Accumulator? The Nut I need to remove is right underneath the A/C Accumulator and I can't get a 15mm Deep Socket on the nut so that I can use an air tool to take off the nut like I did on the Driver side. Is my only option to use a 15mm ratcheting box end wrench or remove the accumulator? On AllData, they show the pics of the Driver Side which is easy to access with just a swivel and a couple of extensions.
View 1 RepliesIs there any particular front stabilizer shock I should purchase for a replacement for my 2003 X 6.0L diesel? Anything I should stay away from?
View 7 RepliesToday I noticed I broke my steering stabilizer shock. It it broke at the connection on the piston arm where it connects to the steering linkage and the piston shaft is bent. Guess it happened when I hit a rock Thursday. I am thinking of purchasing the Rancho 9000 adjustable shock as a replacement. I do not do much off road driving and what I do is very moderate. This is for a 04 Excursion, 4x4, 6.0PSD, with 285 all terrain tires, no lift.
View 7 RepliesCouldn't get the bolts out of the bushings so just bought new mounts. Was wondering to have the torque value for the u-bolts...
View 2 RepliesI fit yesterday my ProComp Leaf Springs 22415 in the back of my Ex. It took about 3hours with a couple of beers to get the work done. Are those springs huge and heavy.
I will change the front springs in about 2 weeks, but we figured out, that we will need there 4 longer Semi-rounded U-Bolts, because the leaf package is about an 1/2-3/4 inch thicker than the OEM-springs. My OEM are a 2Leaf Springs and those ProComps 22410 are 5 Leafs.
I own a 05 XLT Screw 4x4. Dual rear shock set up? My truck drops in the rear when I load up my quads and attach my trailer. I could do an add a leaf but thought a dual shock setup might look and perform better. I am going to add traction bars also because I get a lot of hop when the bed is empty and I'm in the sand.
View 6 RepliesI am looking to install a new Message Center in my 2003 Excursion XLT. I have checked the vehicle for wiring and everything seems to be in the right places. I have ordered the Ambient Temp Sensor and that will just plug into the harness that is on my vehicle with a factory cap in place at the moment. However when I tried to order the message center, the dealer said it would be best to get the part number off one that is currently in a vehicle.
View 13 RepliesWhile fixing some trans leaks on my 6.8. I was tightening a clamp on the center cooler and the lines must have rotted. It snapped off. I was having problems with both attachment points. So guess it's just time. Problem is I cant find a good part number to order one. I can't find it on Rock auto. Here is a picture if it. It's between the front and main radiator.
View 10 RepliesI recently broke my rear shock mount plate, it is rusted to crap. So I need to fix it, I was gonna weld it but there isn't enough metal to weld. It looks like it can bolt in bolt out. I am having trouble find a replacement.
View 3 RepliesI am swapping to a 6.0 trans cooler in my 7.3 and want to add the external filter as well. I looked through the tech folder and the link about the external filter doesn't seem to be working. I am just looking for part numbers of what everyone is using. Is the Magnafine as good as a spin on style filter?
View 11 RepliesWhat is the size of the bolts on the rear axle that hold the shock absorber? I believe its an M12 x70 mm long??
View 7 RepliesYesterday evening my wife was following me down the road for a few hours, we are moving some stuff between houses. After 20 minutes she called me and said she could see occasional sparks under the truck,
Sparks?
A side of the road discussion determined she was seeing sparks near the drivers side rear shock absorber. I looked closely at that area and could not see anything that looked burnt. I felt the shock, axle tube, brake, brake line and E brake cable, but nothing was hot.
I was just in the middle of doing the V Code leaf spring swap and noticed a broke part where the u-bolts sit and what looks to be attached to the trac bar. The piece is broken in half and I am not sure how this happened or when. The piece is welded to the axle.
2003 Excursion 4x4 6.0...