Ford Excursion :: Pulls To The Right While Braking
Jul 9, 2015
Just as the title says I'm getting a good pull to the right when braking. Little background, truck has 155k, rotors and pads replaced 10 days ago, new tires today. Now with the new tires the pull is more pronounced than with the old tires but has been there, which I thought was just worn out rubber, apparently not.
All caliper pins are greased and moving freely, and for kicks I replaced left pins to see if some how they were fouling up, they weren't, still pulling. So my question after searching is maybe the last two culprits are bad caliper or bad hose? I just wanted to bounce this off the board and see if I am on the right track to fix this issue.
View 4 Replies
Advertisement
My 2003 F250 6.0 pulls to the right when driving at any speed. In order to keep it going straight the steering wheel must be slightly tilted to the left, not much but a little. When the brakes are applied hard it will go to the left slightly if you are not holding the wheel good. Neither of these are terrible, just a nuisance. I'm worried about uneven tire wear too. One front wheel bearing was replaced a few weeks ago. It had this problem before that and still does after. Does this sound like an alignment or maybe something more?
View 13 Replies
2001 Ex 7.3 4x4 with 4" lift (6" with 37" Pro Comp tires)
All new front end steering components.
All new Shocks (bilstein)
All tires properly inflated to same PSI
All new brake rotors, calipers, caliper mounts, and pads.
When under hard acceleration the vehicle pulls to the left and I have to compensate by steering to the right. Under deceleration the vehicle pulls to the right and I have to compensate by steering to the left.
I am about to change all four brake lines to Braided Stainless Steel lines, replace all leaf spring bushings with polyurethane, and install a rear anti-sway bar. I'm going through this methodically enough or am I just building a brand new truck one part at a time?
View 14 Replies
I have a 2002 F350 4x4 diesel. When I brake it pulls to the right momentarily then straightens out almost immediately. I've heard that this can be caused by bad ball joints, but I just had all four replaced less than a 15,000 miles ago, and I keep them greased regularly(every oil change). The rotors are a bit warped, but would that cause only a momentary pull? Other than that the brakes are good. I'm sure that the shocks are due for replacement. Tire wear/pressure is good. I had an alignment when the ball joints were replaced.
View 5 Replies
My 99 Ranger pulls severely to the right under Normal braking, pulling the 30 amp ABS fuse stops the pulling but the ABS light is on on the dash.
View 1 Replies
So I've been noticing the truck pulls left when under braking. So, I replaced the front calipers. Now, it still pulls left. When I got home I felt the discs on all corners and found three about the same, barely touchable, and the front left a little warmer. So, it seems its braking more, but its brand new. So, what should I do? They are also pulsing a little.
View 14 Replies
Just replaced break pads and rotors. Inner pad on left side was gone leading me to believe slides were not working properly. Pulled apart, cleaned and greased everything, and replaced pads and rotors. Calipers seem to be working fine. Now when I break hard, the truck pulls badly to the left. When I break softly, it seeks normal. My front end is a bit out of whack and veers just a bit to the left. Do you think this is my issue with the breaking ? I'm getting new tires and an alignment soon but was just curious.
View 3 Replies
Truck pulls to the left while braking, pretty bad. So, pulled the front right wheel off thinking the pins are stuck again as last year. Bottom pin was fine, top pin pretty gummed up but not froze so I cleaned it up good, used thin layer of the good stuff, put back together and test drove........same thing. Pulls left upon braking just as bad as before. Caliper pistons seemed fine, didn't take much to compress them either. Would a right rear cause this?
View 14 Replies
I put on a new set of tires (X Radial) at Sams Club with installation plan which includes balancing. I also brought the car to the dealer to have alignment (front I guess) done. The car goes a straight line no matter what except it always pulls left if I release the steering wheel when I brake from a high speed.
View 7 Replies
Had mechanic check suspension components, alignment is fine, nothing looks damage or needs to be replaced. Tires are 35 inch and practically brand-new...
View 3 Replies
I have a 2000 XLT, V10, Auto, 4" suspension lift on 315/75R16. It recently started pulling to the left and has been getting worse. At <5mph the steering wheel will pulse to the left almost a quarter turn if you let it go and hold there. At actual driving speeds it feels like a constant pressure. The tire appears to have a wobble to it when driving, I know this because my wife drove followed me in it so I could observe.
It also turned easier to the left than to the right when I jacked up the front end and both wheels spun with ease. I have checked the tire rod, drag link, ball joints, and wheel bearings. They all checked out. The last things I can think to do would be to check the steering stabilizers, I have the dual inline set up, or swap the front tires and see if the problem moves from left to right.
View 7 Replies
Could my strut replacement have anything to do with my 2009 pulling left when I brake.
View 6 Replies
I have uneven pad wear on the front discs. The passenger side has about 1/8" pad left, while the driver's side is almost new. The car pulls to the passenger side on braking.
I've had a bad hose on a different car which caused a caliper to lock (and actually lit the pads on fire!), but both calipers are moving when the brakes are applied.
What I'm trying to figure out is how to determine which side and component is defective. It seems to me that a partially blocked hose or iffy caliper on the driver's (unworn) side could cause it to have low power. How do I diagnose this?
View 4 Replies
So my 01 has been parked in the garage for about 2 months. Normally on battery tender but it accidentally got unplugged and I didn't realize til yesterday when I went to start it. So I got the battery charged up and put air in my rear drivers tire since every time it sits it goes flat. Well I did all this I so I could take it to get tires today.
Driving to work and its shaking pretty bad at highway speed. Don't recall it doing this yesterday. Never really did this before either. The truck also pulls hard to the right. Its done this for a while so I'm not sure if it's just the tires or needs alignment or something else. Or all of the above.
I'm mainly concerned with why it was shaking. The front tires don't look low however I will check the pressure on my lunch hour today.
View 13 Replies
My passenger rear door handle opens at almost end of the pull if that makes sense. This is different than the others. Is there a way to adjust it?
View 2 Replies
My 2002 Ex 4x4 developed a shudder during breaking. Today while trying to jack it up and put on jack stands. My 2 3/4 ton jack was too weak/short to lift it up to put on stands. I am using 6 ton stands just to lift the front.
So have to get new jack. Keep in mind I don't have a ton of cash for new jack. What size are you all using to get your ex up on stands?
View 14 Replies
I think I have a stuck/sticky caliper. I am getting some squealing while under way after braking. It will fade away after a little while, but it it's bad enough where a friend left a message saying he could hear me coming...
I am also getting a shudder when braking at certain speeds (from @ 20-30 mph).
I replaced my front rotors @ 40k miles/4 yrs ago w/ PowerSlot Cryo's & Hawks LTS pads on all 4 wheels. I greased the pins at the time on the original calipers ('04 4wd 6.0 X w/ 105k miles now). The brakes have been great since, but the squealing/shudder started this spring.
Is it likely I need to replace the whole caliper, or can I get away with a pin kit? I want to order all the parts and be ready to do a weekend job.
Could the shudder be from the caliper, or is it likely i need to turn the front rotors? I'm planning to put new rear rotors on & new Hawk LTS pads all around again at the same time as dealing with the caliper. What rear rotors &/or calipers to get? I'd like to spend a bit less on the rear rotors vs the Powerslots.
View 2 Replies
If I brake hard a dozen times, 8 or 9 will be normal, a couple times it will pull to the right but as long as your hands are on the wheel you can barely tell, and maybe once it will pull really hard. I have Hawk super duty pads and Ebc rotors with less than 5k on them and I just replaced the front calipers and hardware because I thought that was the problem.
It's not even consistent. Could possibly be rear calipers (rear also has new Hawk pads and Ebc rotors with less than 3k on them) but I don't think it would pull that hard. Tire pressure is even between sides btw.
View 12 Replies
My 2000 v10 w/194K has developed an intermittent shake when braking. Severity from mild to severe. Had the problem earlier, suspected the rotors - replaced front rotors and pads with EB slotted rotors and Yellow Stuff pads. It was fine for a couple of months, now its back. Replaced the slide pins last night (they were in good shape, replaced anyway). Where to look next?
View 14 Replies
We have the 6.8 4x4 2001. Mostly use it for towing 6K #. Bought 2 years ago. Front and rear brakes were new and all 4 rotors were machined at Ford dealership prior to purchase. Have put on 13,000 miles since then, majority towing.
View 14 Replies
So I just bought a 2004 Ex 4x4 4wd with only 50k from a dealer. While test driving the truck would shake/shudder when braking at 50-70 getting worse if you were going faster, as a condition of the sale they said they would look into it. They did and said it was the tires?? They balanced and rotated and did and alignment. Are they correct? the tires are BFG AT 33x12.5x16.5 on aftermarket rims.
View 11 Replies
