Noise on acceleration, sounds like a miss but engine feels good and no check engine light, eventually goes away, not there under a load either, idk totally stumped.
View 10 RepliesI just installed glow plugs, ucvh, stage 2 rosewood injectors, t500, ipr and gear head tunes. I have out 97 miles on the truck since all this was installed and the truck seems to run okay but has a rough idle and sounds like there is a mis? What should I look into first?
View 12 RepliesMy 2004 Elantra has a rough idle when it starts up cold and sounds like it has a miss. When it warms up it smooths out. What could be the cause of this?
View 11 RepliesI have a 97 f150 with 4.2 4x4 auto. I have a bad miss under acceleration. if i ease on the gas no problems. stomp it and it chugs and pops back thru airbox til it gets to 2500 rpm then clears up. If I shift it manually and keep rpms up its fine till it gets below 2500. I have replaced spark plugs, plug wires, fuel filter, upper and lower intake gaskets, cleaned injectors, new air filter and cleaned o2 and mas sensors. Had vacuum system checked and was told all good.
View 12 RepliesMy truck is developing a hesitation or a miss when accelerating. It only does it in the beginning of accelerating like when just starting off from a stop. Seems like its more noticeable with the more I get on it. If that makes any sense. When just lightly accelerating it doesn't do it, like going slow through town from light to light. But when I give it more is when I feel it. It seems like it only does it before the turbo kicks in and it puts out a little smoke too only before turbo kick in. After that it runs good with no noticeable miss or anything. WOT runs feel good after it clears up. Its just when first starting out with anymore that 1/4 throttle I can feel it.
View 14 RepliesUnlike Ap24, who has a post/thread about his CONSTANT noise under acceleration, mine is only happening once. For instance say I'm sitting at a stop light, and start accelerating, it's almost like the body shifts backwards. When I come to a stop and jab the brakes a little, its like it shifts forward. My dad seems to think it is the U joint.. but i'm not convinced as it does it on deceleration.
View 11 RepliesOk - I admit, I don't have a good description of what's going on, but it's not normal. When I accelerate slowly, or go up a hill, I'm hearing a "rattling" sort of noise that did not used to be there. I have heard it also when slowly decelerating.
I need to crawl under and look, but my big concern is I'm about to go on a 2000 mile trip with a small horse trailer. Could this be a festering major engine, transmission, or otherwise problem?
2001 v10 ... I have a thumping noise under acceleration... also hear it if brake torquing.. I do not hear the sound if in park or neutral...while riding down road the sound goes away when you let of the gas. Torque converter has been replaced.... exhaust manifold bolts are ok too. Been to 3 places and no one can seem to pin point it or no where to begin...
View 7 RepliesI posted a while back about my 04 5.4 having an issue at idle. I did all the normal things like replace coil, spark plug, etc etc. No change to the issue. It still acts as though it's misfiring on a cylinder and I get codes P0306 and P0316. Finally took it to ford and had a diagnostic check ran. Everything on the top end was in working order. The tech even put a known working coil on 6 and nothing changed. I was told that it's either an intake or valve issue on that cylinder. But no definite answer to problem.
Fast forward to yesterday. I got a wild hair at lunch and went out and started truck. Pulled injector plug off of 6. No change to the way it was running. I did the same for 5, 7, 8, 1, and 2. All of which made a big difference in the way it ran. It was obviously misfiring with no fuel to cylinder. This gave me the idea to swap 5 and 6 when I got home to see if the issue followed the injector from 6. I did NOT. I pulled the plug on 5 and got the obvious change in the way it ran. So there is definitely something going on at cylinder 6 that I cannot figure out.
PCM, bad intake, bad valve? I'm not rich so a trip to ford for repair is gonna have to wait. Truck seems to run fine when driving except for slight hesitation during acceleration.
2003 F150 5.4 72852 miles
I have a Rough Idle & sometimes a hesitation or stumble on acceleration. I cleaned the MAF & IAC motor & Air & Fuel Filters are new. I got a 20890 scanner & ran test 6 53 as suggested in many posts by BlueGrass. Here are My results & what They Convert to.
1 00F5 .3675
2 0051 .1215
3 0000
4 0000
5 00A3 .2445
6 0000
7 0000
8 0000
I'm guessing the cop's are ok & probably need plugs? I was hoping to just swap a coil. Too cold to do plugs & truck won't fit in my garage.
Installed the Riffraff gauge kit and the check engine light came on about 20 miles after install and the Ex now randomly has a hard jolting miss, just for a second then its gone. Took it about 4 or 5 times of the jolting miss then the check engine light came on.
Could something have been unplugged or could the manifold air intake heater delete be causing the light. Ran fine until the gauge install. I remember reading something about the ground for the manifold air intake heater being a issue if not care full. I could not get the dam thing off so tapped the end and left it. The ground post kept spinning not allowing the ground to come loose. This thing is becoming a pit I cant feed fast enough.
If I can figure this out before Monday that would be great. If not I am tired of dicking with it and am just going to take it in. Don't have a scanner that will read the codes so SOL there. Unless there is some way to get them off with a flashing light sequence. I would love to find out how to do that. I don't want to drive it anymore than I have to as if one more thing goes wrong with this dam thing........
I've seen the gods of the diesel engine do some amazing things on these forums, so after a year of pulling my hair out, I've signed up to try this myself.
This time least year,I bought a 2004.5 6.0L F-250 with 196k on it to haul around the state for my new business. At this time, I knew nothing about diesel engines AT ALL WHATSOEVER, but I've never been afraid to tackle anything and mechanics are not totally foreign to me. Not to mention, I was hoping everything might just go peach-ily for at least a couple years. (for what it's worth, My dad and his family are mostly shade tree mechanics and I'm a power plant operator so mechanical concepts are not totally foreign to me, just never had a diesel before)
To begin, I purchased the truck and everything was fine for about 2 weeks. Then abruptly one morning I noticed a couple of hefty surges on the way to work. Then, on the way home I thought all was well until about half way home, it did it again! as I was pulling up, it galloped once I pulled my foot off the pedal. like ba-DA-DA-DA-da-da-da-da-da-da-DA-DA-DA-DA-DA-da-da-__ and then STALL! Shaking with concern over potentially an awful purchase, I turned the truck back on only to find... that it's fine?!?? No problems for the next two days and then it happened again. then good for a week, then again. then good for 2 weeks, then again. so then I bought auto enginuity and an edge insight to do some troubleshooting. Let that sink in as I explain it's history a bit.
-All but one injector is ford remanufactured the other is stock (was never told which one)
-replaced head gasket with another OEM
-ARP Head Studs
-EGR delete
-HPOP AND STC fitting both replaced
-FICM replaced
-Oil cooler replaced 50k ago
-ICP and pig tail replaced right before my purchase
- Has been through roughly a handful of ICP's since I've had it (I'll explain)
-I've cleaned the EBP tube a lot and updated it to the newer ford sensor with the flare fitting
-I use Rotella T6 5W40 and CAT ELC-1 Coolant.
-Deltas are under 10 at normal driving
-I typically drive under 2200 rpm until warm then like a banshee at operating temps.
Now one year later, its not fixed, but I feel like I'm close.
The DTC's I have seen are ICP sensor circuit intermittent (I think po2884) and Power Blance contribution failure from cylinders #2 #7 and #8 but never at the same time.
Every time I replace the ICP, it will be problem free for about 6 weeks and then it will return full force (surging and galloping when warm about 50% of the time)
During a possession I see the following:
*Cylinder power contribution test yields no issues at idle or when cold. when "possessed", the whole baseline across all cylinders goes up and all cylinders dip and return at random. none singled out
*ICP voltage fluctuating from ~.6v to 1v (.24 @koeo) *Also during a surge*
*ICP PSI dancing up and down ~600 to 900psi (0.0 @koeo and ~500 at normal warm idle) *Also during a surge*
*IPR% bumps up and down ~25% to 30% (15%@ koeo and 23% at normal warm idle) *Also during a surge*
*FICM Voltage anywhere between 47.5v and 49v
*EBP is normally 15-20 psi
*Boost is 1-7 normal and is not affected by "possession"
These numbers have taken a long time to get since it will only be possessed for about 3-10 seconds at a time and then will disappear for days. The stall has only happened about 5 total times in a year. The surging is much more frequent. I usually get a buck or 2 on any given trip that is longer than a half hour but NOT IMMEDIATELY AFTER AN ICP REPLACEMENT.
On one occasion, I noticed that the ICP PSI actually tanked to about 350 right before the IPR went from 25% to 40% right before a posession. I was driving about 35mph through town at the time.
Here's my thoughts...
- Did that one occasion clue me in to an intermittent HPO system leak causing the truck to briefly over-compensate by spiking the IPR?
- Is my ICP pig tail jobby done incorrectly? If there was a short, wouldn't I see the volts drop to 0? I have another one and will replace to rule it out.
- I have yet to test my fuel pressure, but I figured if it was low, I would have lost injectors by now. (I replace filters probably too often but next empty tank, I'm dropping it and checking the screen and strainers)
I should also mention that I have buzz tested the injectors and I can hear each one clear as day, and that for REALLY long trips, it actually returns to normal. In other words, my window of death is between 30min and 2hrs of driving; invincible after.
I am a proud new owner of a 2000 X 6.8l 2wd with the 4.3 rear end .
I have had the truck for 2 weeks now . When I bought her , she ran a little rough but I expected as much after sitting for 6 months ... After driving her home I began to start a massive tune up , because she was acting like there was a miss ... The miss only started after she was at normal operating temp and at first only when at cruising speeds in overdrive on the freeway , it progressively got worse ... The miss became all the time once up to normal operating temp but will do it wether she is in any gear or even park .... Oh and the miss is NEVER at the same time it is always completely random ...
I have changed all 10 coils , all 10 plugs , the PVC valve , and I am changing the fuel filter this afternoon ... Other then that I think I can hear a vacuum leak , but I have tried spraying carburetor cleaner around the engine bay as instructed by a " ford expert " at the local auto parts store and I did not notice any change ... After I install the new fuel filter I am going to fill her full of 93 octane and add a bottle or 2 for Lucas octane boost as well as the Lucas injector cleaner ...
Other then these things I am at a complete loss ! This is my first v10 ford so I am a little at a loss ... Now if this was my wife's BMW 760 or my Lexus IS 300 I would not be having this problem.
I developed a significant miss on my '00 Excursion 6.8L yesterday and threw a P0306 code. Since the engine has 178K showing and I bought it used, I am planning to replace all the COPs and plugs.
Recommend one COP over another; motorcraft over Accel, etc.? Any preference for spark plugs?
I have a 2001 Excursion with the V-10. Two weeks ago, the upper nipple on the radiator cracked and I overheated. Was towed home and replaced the radiator with a quality aftermarket one. I then drove to the whiz wash and cleaned the antifreeze off of the engine.
Immediately I noticed a slight "miss" when cold, particularly when backing out of my driveway. I have no lights on the dash and it is throwing no codes. The miss gets much better (almost gone) when the truck is warmed up.
Question, my truck started to have a miss under normal acceleration, when I really get on it, it clears up? I also noticed a bad sulfer smell at idle. Im thinking the cat is possibly plugged? Truck had 172000ish on it, and the cat is original. I did do a big tune up this past fall, new plugs, coil packs, air and fuel filter. Should I put a new cat on it? And a new oxygen sensor?
View 9 Replies2001 V10 160000 miles.
1st happened Wednesday on way back. Temps all fine but had been in stop and go traffic earlier. Truck was on cruise and felt like fuel cut. I disengaged cruise. Throttle would keep it running and within 5-10 seconds it caught and ran fine.
Connected and reconnected all injectors, coil connections, tb and MAF connections. Nothing noted loose. No codes on OBD reader.
Drove around town last couple days no issues. Today towing three dirt-bikes about 45 miles. towards the end of the 45 miles. she stumbled as we crossed an intersection. Then caught and ran fine. Did it twice on way back home towards the end of the trip.
Had OBD reader in gauge mode with ignition advance, tp sensor, voltage and gallons per hour showing. None seemed to change when it stumbled.
Fuel pump is about 2 years old. Coils maybe 4 or 5 years old. Aftermarket. No codes on OBDII reader.
165k miles 4x4 6 speed, bone stock unmolested
Slowly progressing problem over 6 months. Occasional miss at highway speeds uphill has progressed to bucking and jerking during even gentle acceleration attempts.
I hadn't got my cam sensor recall done but no change after that procedure completed yesterday. Oil recently changed as well.
I have a torque pro but it never finds any fault codes even though 'service engine' light comes on sporadically. I'm not sure I'm operating it properly but it at least reads rpm when its running.
I'm contemplating the hutch mod but I'd like to have an official diagnosis beforehand if its possible in my case.
Woke up to go to work and it started up with a rough idle, got a block down the road and it had a slight miss under acceleration. Guessing its a bad coil, I've got a spare featured I'd play I I mini miny moe when I get home unless.
View 5 RepliesI purchased a 2010 2.5 Altima with 9K miles in 2011. After @ four months I noticed a slight miss at 30-45 mph upon acceleration. I told the dealership and they said it wasn't throwing a code. After two more visits I again complained about the miss. At this time the service person handed me a "Customer Satisfaction Bulletin" that explained that cars (Altimas, 2009- 2011 with my trans. and engine experience this "SURGE" as they called it AND that it is NORMAL.There is no way in hell that a auto maker would produce a car that does what my car does and consider it NORMAL. Buy the way, there is a "FIX" that was done but didn't work, that involved changing motor mounts and computer programming.
View 8 RepliesI had a flow master 50 sieries on my v10 and it sounds like something rattling around when towing. Guess i will have to find something different later on.
View 13 Replies