I have checked all fuses, checked wires on top of steering column all checked out ok. Hazards work but when I press brake tail lights just blink with no brake light but the 3rd brake light works??? Signal switch maybe??
View 14 RepliesWell, on our way home during my leave, the wife made the comment about halfway home that the blinkers had quit working. I assumed it was probably a fuse or relay, so we came on home. I have been looking at it for a few days now (too hot to spend too much time out crawling around under the dash ) and I am still having some trouble. My brake lights, and hazards are not working, and neither is the cruise, which was working fine while I drove before the blinkers went out.
I have no power at all to the flasher relay. I replaced the brake light switch because it was definitely worn and looked a little burned inside when I pulled it out and inspected, but still nothing. Have not found any fuses blown. Brake pressure switch fused link harness seems good with my test light. Wipers, brights, everything else on the turn signal switch works fine. Can't even get the cruise to go into diagnostic mode, it only blinks once when I try.
Every time I step on the brakes, there is a bright spark in fuse #13. My brake lights, turn signals and hazards don't work. At this point my truck isn't drivable.
According to the owner's manual in my truck, says circuit #13 is for "stop lamps, CHMSL/hazard, trailer tow stop lamp, and speed control."
I'm assuming that the hazard part covers the turn signals as well, but I know the cruise control works even when the fuse is blown. I used it last night on the way home (this was before I realized I didn't have brake lights).
So I know I have a short somewhere. The only mods I've done to the lights are aftermarket headlights, but if the fuse only gets blown when I step on the brakes, I don't see what that would have to do with it. Also, the lights have been installed and working for about a month before this started. The only thing that I did around the same time was install the gauges. I ran the power to them from #5, the customer access circuit.
Are there any other "common" areas for this to happen? I already removed the rear brake lights and it didn't work. I am quickly running out of 20A mini fuses.
I found out last night that all 3 of my brake lights are out. However, my tail lights work, and my turn-signals work. So obviously its not a big wiring deal. I was looking for the brake switch but i don't know where its at because i looked underneath. What fuse is the brake lights cause my manual doesn't have it listed. I drive a 04 Elantra GLS.
View 6 Replies2004 Prius here. The turn signals and hazard lights stopped working a few days ago. I found a disconnection in the grounding and repaired it. Also replaced the fuse and the flasher switch. Now the lights work, and I can hear the flasher switch clicking, but they don't blink!
View 13 RepliesDad borrowed truck and wired 7 pin trailer harness. Lights worked on truck/trailer for use but upon return the turn signals didnt work. Hazards and running and brake lights did work. Replaced TS flasher and Haz flasher. Still no signals. Pulled steering wheel and replaced turn signal cam only, not whole switch. Now no brake lights, no rear hazards or turn signals. Losing my marbles trying to follow schematic and using test light and mulit meter. All bulbs and fuses are good. Running lights and head lights working as well.
View 6 Replies2005 F350 Super Duty. I have no brake lights turn signals or hazards. dealer suggested the multiswitch but changed it and still not working?
View 2 RepliesToday, I replaced the flexible coupling in my steering column. All went well and seemed great until I realized my turn signals were not working. I tried the hazards and promptly heard the 10amp fuse blow. I took the paneling back off and realized that the wire bundle to the turn signal was being pinched above the steering column.
After lowering the front of the column down and removing the wires, I noticed that there was some damage. One wire (blue) was cut and a few others had damage to the sleeves. I repaired the sleeves and fixed the broken wire. The turn signals now work perfectly fine, but when I activate the hazards all the signals go dark. I cannot find any blown fuses and the relay appears to be working just fine for the turn signals.
I recently bought an 08 Sonata from a used car dealer which has 65,xxx miles. Last week my turn signals would work intermittently, and now neither the turn signals or the hazards work. I put in a new relay and a new turn signal switch, to no avail. When I turn the hazards on, the relay clicks once then nothing. When I do the turn signals, nothing clicks. Is there another relay I'm missing somewhere?
View 14 RepliesI have a 2004 F150 XLT and the passenger side tail light doesn't work whatsoever. The light does work for hazards, turn signal, or when braking. The passenger front turn signal works, so does the front and the driver sides tail light. Only the 1 tail light doesn't work. I bought a new brake light bulb and it didnt't fix it, so i swapped the drivers and passengers bulbs out, and it still didn't work. I replaced the 10 amp fuse (#36) in the fuse box. What is causing the problem.
View 2 Replies2000 V10 F250 - daughter is using my truck and called to tell me the turn signals weren't working. She called me shortly after and said she adjusted the tilt and hazard lights came on and now she can't turn them off. I had her pull the hazard fuse to stop them. She then noticed the brake light weren't working. I don't know if the brake lights were because she pulled the fuse or she just noticed they weren't working.
A week or two ago, she said she parked the truck, turned it off and took the keys. When she came back out, the truck had rolled across the street. Periodically, over the years, I would go to start the truck and nothing happened. I would shift the gear selector in and out of drive. Then the truck started.
Finally, since I've owned the truck, the when I activated the left turn signal, the selector frequently wouldn't stay "locked" till I turned. So, are these related? Do I have multiple issues going on in the steering column. Where to start looking when she gets the truck home?
This has been driving nuts for 2 days.... Brake lights dont work. Either pushing pedal or turning on lights. Turn signals work just fine.
Cab/cargo/3rd brake light on back of cab doesn't work either. I have checked/done the following:
- Checked Brake pedal switch for continuity. Tested fine.
- put multi meter on wiring all the way back to brake lights. No drop in voltage.
- changed bulbs. #3157 dual filament.
- positioned steering wheel all the way up and all the way down as suggested on here. No change.
- checked multi function switch (turn signal switch) for wiring issues. None found.
- kicked rear quarter panel for caveman adjustment out of frustration. No change.
What am I missing?
I have had this problem for a while now, but can't seem to figure it out. I'm sure it's an electrical issue, but I'm not that great with electrical. My turn signals don't click when I push the handle in either direction. The turn signals come on and stay on but don't blink like they should. I checked the lights in the front and back and they just stay on but don't blink. Also my hazards don't blink. They just stay on and don't make clicking noise either. My horn doesn't work and my door doesn't ding with the key still in the ignition but in the off position. I don't know of it's all related or different issues.
View 10 RepliesI just bought an 05 F250 XLT. I noticed tonight that the rear turn signals and brake lights don't work.
The front turn signals work fine, although they flash fast. I know that usually means a light on its way out. neither taillight flashes though, which puzzles me.
My second issue is that, of the 3 brake lights, only the high mounted light illuminates when I hit the brakes.
I've got a 98 Silverado. Break lights and rear turn signals won't work but tail lights and reverse lights work. Also the brake light on the cab does work.
View 6 RepliesSo I lent my santa fe to a buddy to do some hauling, I got it back yesterday and the turn signals and the brake lights don't work...notta. Regular running lights are working without issue, but no turn signals, no hazards, no brakes. Even the "tick, tick, tick" of the turn signal is gone, it's just dead.
View 1 RepliesMy sons 2006 F350 brake lights and rear turn signals quit working. When the headlights are on, all the lights operate but the rear turn signals and brake lights do not nor do the emergency flashers. The front signals work but flash very rapidly. Although I'm not an auto electrician, I'm fairly mechanically inclined but the fact that the front signals work, the rear don't and all lights work as lights, just not as turn signals or brake lights.
View 4 RepliesAll of this happened at the same time so has to be related. The a/c system has no power, the brake lights and turn signals don't work, windows wont work, air bag light on. However, the park lights, head lights and hazards work fine. Starts and runs fine. All fuses check out ok. New battery as well.
View 3 RepliesRecently my tail lights went out and my turn signals dont work either, the light for the turn signal on the dash doesn't light up either. My brake lights do work tho and so do my reverse lights.
View 3 RepliesI have a 2003 V10 Excursion with an electrical problem. The right turn, right brake and right hazard light do not work but the flasher makes the clicking noise. When the right turn signal is on, the right front turn signal light works but is at double speed. The right rear light does not work. Same when brake and hazard are applied.
I checked the bulb socket with a multi meter and have no current. I also checked my trailer plug and have all functions work. Fuses were checked also for the brake circuit and were all ok.
My '99 F150 is having wiring issues. It started with a left flasher being fast and the rear bulb not working. I put in new bulb and that didn't fix it. Then I realized that I also had no tail lights. The reverse lights are good and the brake lights work too.
So far I have searched for and repaired suspicious splices done by PO, added a ground wire that was cut off from the trailer wiring harness, checked every fuse that I could with an ohmmeter and I pulled the multi function switch and tested it with an ohmmeter also. It tested fine but I did find one of the female pin connectors had pulled out of the harness. I managed to get it back in and seemed to click into place alright. Somewhere over the course of all that I now have both sides of my flashers fast and still no tail lights. Good news is that I haven't broken my brake lights or reverse lights yet.
Could I have a bad flasher relay? Earlier in the process I did have my 4 way flashers working correctly and a couple times I even had the turn signals going. Now, none of the rear blinking lights work but the front ones go 90 to nothing and I still have no tail lights. My truck does have the auto lamp thing.