Is it ok to keep my front hubs locked in and the switch in the 2wd position for everyday driving? Only reason I do it is because in auto it doesn't always go into 4wd.
View 11 RepliesIts a 2016 F-250, 6.2L gas truck with the electronic shift on the fly transfer case.
I have put right at 22,000 miles on it like this, frequently at 70-80 mph.
What are the odds I have damaged it and is there anything I should do now that I discovered it - other than put them both in "AUTO".
Truck has been to the dealer twice and not once was this noticed. They blamed the squealing on the brakes which I knew it wasn't.
A relative's '04 EX Limited is having an odd problem. He put it in "4x4 Low" to back a trailer into a barn and after the task was complete the transfer case wouldn't shift out of low range. He tried multiple times and after about 5 minutes of fiddling around with it, it shifted into 4-Hi but wouldn't go back to 2-Hi. The hubs are in the "auto" position and will not manually unlock (the selector turns). 4x4 indicator on dash is not lit. Could the dash switch be bad? Why would the transfer case and hubs act up at the same time?
View 6 RepliesI have been recently told that it is bad to drive my F350 with the manual hubs locked when I do not have it in 4 wheel drive mode. There are times when plowing snow that the roads are cleared but I am still plowing driveways. I do not want to travel with 4 wheel engaged in the scenario. So I would just disengage 4 wheel and travel to next stop. Is this a bad procedure?
View 10 RepliesI have an 04 F150 (4.6, auto, 4x4, SCrew) with 300,000 miles. Any success modifying existing 4X4 IWE actuators so they are always locked in?
My last set of actuators didn't last long My vacuum is too low under hard acceleration... Actuators partially engage leading to early failure.
I'd like to take an actuator apart, modify it so it's always locked in. Some loss of mileage? Other ramifications?
My Excursion is having an issue with the 4x4 system. The. 4x4 selector switch on dash lights up properly for 4x4, but the auto hubs don't actually engage. The hubs will lock only if I manually lock the hubs. I can hear relay click, so I don't think its electrical. The hubs had new o rings installed when I did front ball joints a few thousand miles ago, and the 4x4 worked fine up until today.
View 5 RepliesThe drivers side Hub seems to be stuck in Locked Position. I lifted the Wheel and when I turn it the Front Drive shaft turns and you can feel a fair amount of resistance.
I lifted the Passenger side and it spins free. I then started it and put it in 4WD and the passenger side engaged and i could not free spin the wheel. I then lifted the drivers side again and it would not spin. Turned off 4WD and it spun again but moved the shaft.
None of my 4 keys will operate my ignition switch.
It's stuck in off position. Steering wheel is not locked and I have pulled pretty hard on it to see if I could get the ignition switch to turn.
I have a new switch on the way but I have to get the old one out and don't know how to get old one out if I cannot turn the switch to on position.
2001 excursion 4'4 V10 XLT.
One or more of my door switches is stuck in open position. Door ajar light on and interior lights on.
Interior lights stay on for about 15 min than go off.
I have sprayed all 4 doors and both rear hatch lock assemblies several times with WD40 and electrical cleaner with no improvement.
When I open drivers door there is no key chime with key in cylinder. Could the hood switch cause this issue? How do I determine which door/doors is/are the offending crimimals?
Is there any way to keep the front white LED lights on with the driving lights?
View 4 RepliesSwapped for Warn standard hubs a few months back when the ESOF's turned out to be trashed.
Since then, I've noticed a rattle coming from the hubs when driving over rough or broken pavement. I've checked the outer caps and they're good and snug, proper amount of grease inside, and the hub itself is completely secure.
Do aftermarket hubs have tis issue? It's not critical, but on cooler evenings with the windows down it sound like a rattle trap unless the roads are in good shape. More of a pet peeve I suppose, but still curious.
We've had our 2012 Camry LE 2.5L since October. In that time period we taken two 400 mile highway trips. The best mileage we've obtained is 28 MPG (hand calculated). That's all highway driving at 65-70 MPH. Needless to say, it's very disappointing. My 13 year old V-6 Mercury Sable wagon gets just over 30 MPG on the same trip.
In everyday driving it's only getting 24-25 MPG. That's mostly suburban/rural driving with some short highway trips mixed in. The car has just less than 10K miles on it, so things should be getting pretty well broken in.
My son has a 2003 Super Duty with auto locks, but the front wheels won't lock even when turn to locked position. Also when it's in two wheel drive the front drive shaft and axles still spin, are the hubs locked up or is it in the transfer case?
View 10 RepliesWell I read most of the 2011 manual last night to find out why I have "M" on my gearshift, & found it near the end...so we can manually shift our gears. So I normally drive in D, and I use the tow/haul switch when trailing...so under what circumstances does the normal person need to manually shift through 5 gear positions using M, and the 5-position switch?
View 7 RepliesWarn Premiums, installed them and now the 4x4 is engaging, but still have a grinding issue. When the hubs are locked and the switch is in 2 wheel drive, the frond end is grinding, if I switch it to 4 hi, the grinding goes away.
View 3 RepliesWell long story short, I had the the factory hubs in my 04 f-350 and I was driving down the road and it started making this horrible popping noise. So I pulled over and couldn't find anything and just curiosity locked in the hubs and all was fine. Made me think my hubs were bad, so I went and bought the warren premium hubs, installed them. Went for a drive and still the same noise is there when they are in free spin. But once they are locked in its fine. What this could be? Wheel bearings?
View 4 RepliesBut on my 2000 SD V10 the hubs are worn I just cant find which way to turn them to auto ?
I'm getting popping and such so I think I'm locked while turning.
Also.... IS there a way to check the COPS with a multimeter? I think I got a bad one.
Had to make a sharp circular turn last night in a parking lot, with the steering turned to full-lock...noticed a very audible clunking or clicking noise during the turn...went away after full-lock turning was released. My hubs are locked in...but I was told there was no issue with leaving them locked in, even during the summer. And there shouldn't be...4x4 disengaged, of course. Must have been the u-joints clicking / clunking? Problem?
View 5 RepliesJust got done with a ball joint replacement on my 2003 F550, everything went together great, just as it should. Until I got to the drivers side hub lock.
I have Mile Marker 449s/s manual hubs. Turn from free to lock and theres this loud clicking sound about halfway to LOCK (passenger side doesn't do this). Hub will stay locked for about 2 rotations, then it unlocks and makes a clicking sound. You cannot turn the hub back to FREE, it gets halfway and stops. I tried forcing it and broke the spring fingers inside. Have a new set on order.
Is this a locking hub issue or an assembly error? I was going to take these steps.
- Take passenger side hub lock off and see if it operates normally or same on drivers side.
- If same, remove axle and re-seat/re-assemble everything again
Anything to specifically check? All the parts went back in, washers were in correct order, outer snap ring is in groove.
Ok so some one locked my hubs and put the truck in 4x4 4low i assume my aunt was driving it, truck wouldn't shift from 2 to 3rd is this normal since its in 4low. The shifter also seems pretty stiff and 4wheel isn't used much if there a way to know if 3rd gear toon a crap? Trans fluid seems fine not dirty or burnt...
View 1 Replies2008 F350 hubs wont stay locked in when in auto position. everything stays locked while in manual and 4x4 works fine, but in auto the hubs wont stay locked while spinning. I was trying to find the problem when i noticed that one hub stays locked all the time and the other locks and unlocks as it should but it wont stay locked while spinning. My question is do I have two bad hubs or is their a leak that wont let the hub stay locked? Also on the hub that wont unlock is this a leak problem as well or a internal problem?
View 5 Replies