I need to send my cup-holder cover and trash hook to Clay so he can color match my F650 dash and I can't figure out how to get the damn side clips on the cup-holder to let go!
I got the top clips and the bottom clip to let go but the side clips will not slip through the slots... I've been near the point of breaking them trying to slide them through...
I took the plastic cover in front of the radiator off to clean the radiator and condenser. It directs air through the condenser before it gets to the radiator and I was wondering if it would cool the engine without it (if you don't need real cold ac air) . Without it the air can go over the top of the condenser and it is still blocked by the flap that stops airflow above the radiator. Also, I am wondering if the fact that the condenser has nothing in it affects the radiator cooling, and is it bad for the AC system to be empty. (My AC doesn't work)
View 7 RepliesI need to pull my front overhead console to make some changes, gonna try to mount my sirius cradle up there to get it out of the way. Can't figure out how it is fastened up there. Also, I need to pull the cover off the rear seat DVD player as I want to solder in some RCA's onto the aux in. Can't figure this one out either, and I'm afraid to break the cover.
View 4 RepliesWhat sort of trick do I need to perform in order to remove the cup holder that is on the front floor of my 2001 4-door Ranger. I'm hoping to be able to remove it without busting it to pieces.
View 4 RepliesI finally picked up a cell phone cup holder so I could dock the Android and tether the millions of cables (two) for power and audio when I ran into a roadblock. The holder has an expanding base so it can fit into any size cup holder. Perfect! Except that if I try to use it in the "top" cup holder that has the closing lid, it never quite expands to fit because the lid offsets the interior dimensions. The holder fits fine in the lower cup holder, but because of it's size and angle for the phone, it presses it too close to the armrest so it's essentially a no-go.
How to safely and easily remove the lid cover for the top cup holder?
My cup holder sticks and will not come out like it should. I believe me brother had spilled some coke on accident. How to remove it. Or maybe give me a "how to" link they know about. I tried searching for this but, I could not find anything. I have a 2000 passat.
View 2 RepliesI was wondering how do you remove the cup holder part of the console dose it just pop off or are there metal clips or screws hidden some how?
View 4 RepliesI'm trying to install an iPod dock inside the coin tray. How to remove the coin tray? The iPod dock fits in it perfectly width wise, but the length is a bit long so I need to remove it so I can drill a slot inside it.
View 4 RepliesI have a 2012 Prius V, and somehow A tin of Altoids has fallen behind the drawer, (hidden drawer) of the center console. How to remove the drawer to access behind it?
I can't see any catch or release to trigger releasing the drawer. I also think accessing it by opening up the whole console from the top is risky as the EV, ECO, and PWR mode buttons are wired into it.
Need to confirm that the 2002+ console cup holders are deeper than the previous models? Are they direct swaps or do I need to cut stuff?
[URL]....
I have water coming in on passenger side right above rear cup holder an another spot further back by rear window. I was told roof rack so i removed cleaned and resealed all bolts around wholes with silicone. Rain today an still have water coming in? See rite on edge of headliner gets wet. How hard is it to remove headliner? Maybe not all way out but could drop enough to see whats going on in rear compartment. Its a 2002 xlt...
View 12 RepliesI need to get the HPOP reservoir top cover off so I can drill/tap a gauge probe into it. I see torque-head bolts, and a few long bolts that go all the way down into the HPOP.
Unfortunately I cannot get two of the torque-head bolts out because they only un-thread several rotations before the heads of the bolts hit the edge of the fuel filter canister/bowl.
I have a 2013 FX4 with the 3.5 twin turbo engine. How to remove the right side valve cover to replace the gasket? I have loosened the perimeter bolts and was able to get it to move slightly but nothing more. I also removed the spark plugs thinking that they might be holding the tubes which are connected to the valve cover by round seals. I have not removed the seals since I was concerned that I might damage them. Do they need to come off? If so how do I do it? It's amazing how complicated this job is! Short of calling the dealer service, I have just about exhausted all my usual tech resources.
View 4 RepliesThinking of cleaning up the engine bay of my Passat 3.6 V6. How to remove the engine cover of a Passat 3.6 V6? For asian cars, it is fairly straightforward.
View 2 RepliesHow can i remove the allow wheel cover off my 2011? i see their are 3 places where u can insert a flat screw driver, but i still cannot get it off. I don't want to break it.
View 5 RepliesIt frustrates me to have to ask but I can't find what I'm looking for after several attempts. The footwell cover just below the steering wheel appears to have hinges at its bottom so I'm thinking the top merely snaps into place but I've found no literature referencing that. I've pulled what I felt was a safe amount with no release and I don't want to damage the cover if I'm wrong on my assumption. I can't see any screws to remove but I'm just not sure, what does it take to remove?
I've got the Bentley repair manual but it skips by this as it's not worth referencing going straight to the cover behind it.
I want to have my oil cap sit close to the valve cover rather then have that long funnel.
I want to go from this:
To this:
I got a piece of cable tie stuck in there.
View 6 RepliesExactly how do you remove the cover (facia) below the front of the front seat so the battery can be removed. To my knowledge no one has spelled this out on this board.
View 7 RepliesI have a 2012 Camry and was wondering how to remove the rear bumper cover? Someone backed into me so I have a shallow dent I want to pop out of the plastic.
View 6 RepliesSo I'm trying to remove the rear bumper cover on a '15, but it has been a royal pain. I went in thinking that the procedure would be similar to what it is on the '14, but it is way more involved. The biggest issue I'm having is removing the large plastic triangular side bracket. It has these weird T-nuts fastened to the body, which you cant remove, and the whole thing looks like it would need to slide upwards to get it off, but you wouldn't have enough room because the shape of the body just gets in the way.
View 1 Replies