Ford Excursion :: Grinding Sound While Turning?
Mar 29, 2013
When turning right, either sharply or just during a long gradual turn in the road, I hear a grinding or running sound consistent with RPM coming from the rear - I think the right rear. It driving flat, no sound. If turning left, no sound. To me, it seems if the right rear is unloaded a bit weight wise, the sound occurs.
I'm thinking wheel bearing. Hoping not differential, but it really does seem to come from right rear not center of rear. Only if turning right and moving weight to left side.
View 12 Replies
Advertisement
I have a 2001 excursion limo with 108,000 its a v-10 2 wheel drive with stock wheels and tires. I believe both my front hub bearings are going out, I am hearing some grinding at slower speeds and while turning, but seems to be ok at highway speeds...Anyway I think I am going to replace both front hub bearing assemblies.
View 12 Replies
I got a 98 f150 with a 2 year old starter in it. When I go to start the truck I turn the key and it makes a horrible metal crunching sound. If I quick stop, then turn it again, it'll start.
I saw another thread here with 'occasional grinding noise' but this just started, and happens every time I turn the key. Is it time for a new starter or should I look towards the fly wheel or something else???
View 2 Replies
2002 XLT 3.0L 4X4
Making a grinding sound when traveling straight or turning left. Any turn to the right (even the camber of the passing lane) and there is no grinding sound so I figured it was the drivers side wheel bearing. Replaced it yesterday.... symptoms are still there.
Tight left/right turns don't result in the popping/snapping of a bad CV joint so I don't think that's it.
I don't think it's transmission related since shifting is good and the grinding is not throttle related. Besides, turning shouldn't have an effect on the sound if it was something in the transmission, right?
View 10 Replies
I can't isolate whether this is in the transfer case or the front axle.
While driving along at a moderate speed in 2WD the truck GRADUALLY began making a grinding sound, similar to riding on grooved pavement or over a steel bridge. It stops IMMEDIATELY when switched to 4WD.
I can ride for 10 miles before the growling begins. When switched back to 2WD the noise returns gradually usually after a minute or so.
The frequency of the sound is faster than the rotation of a driveshaft and it continues right down to a very low speed at just about the same intensity.
I've read a few posts on here that suggest spindle bearings, but the problem came on very abruptly and usually bearing problems, from my experience start small and get worse. Last week I changed brake pads and rotors.
View 10 Replies
I have a 2000 excursion 6.8l v10 4x4. While driving on the highway and reaching 80mph, the suv starts making this grinding sound like it's trying to get into gear. The SUV starts to shake. when i drive at a lower speed it goes away. it doesn't make the grinding sound while driving on back roads. What could it be?
View 5 Replies
I got new tires a few months ago and when the shop was putting them on they said the driver's side ball joints had a little wiggle in them. I've noticed it has gotten worse and I am going to change them prob next week. I am just going got do both sides while I have it torn apart. I have found some great info on how to do that. I also have noticed some ratcheting sounds from the drivers side hub when I start the truck and accelerate, and then it feels like there's a pop and the sounds goes away. Also if I flip on the 4x4 switch while there is the ratcheting sound it goes away. Is that just from a vacuum leak in the system? I don't know a whole lot about that, or what hoses are vacuum hoses etc.
I haven't really looked in the manual that much yet. My big question is this, I was driving down the freeway going about 70 when all of a sudden there was a gear grinding type sound, kinda like when you try to start a car that has already been started and the starter teeth make that grinding sound. Could it be that the axle has started to get some play from the ball joints getting worse and then it just reached the right RPM to cause a crazy vibration? Or could the 4x4 have a possible malfunction to where it tried to engage but the truck was going too fast? It hasn't happened again, but I have not gone 70 again either.
View 10 Replies
I have noticed this rubbing, not quite grinding sound/vibration when I take off and turn. For instance pulling out of a parking lot and turning either left or right. Truck will do it only after it's been driven a while. I originally thought it was just the limited slip ratcheting but recently just changed the rear axle fluid adding Amsoil this time. I did not add any friction modifier because I didn't think the Amsoil needed it. So after going on a 500 mile trip I find it is still doing it. The truck sits at the stock ride height and has stock size wheels and tires on it. What it could be ? It only happens in the turn, not while driving straight. It still sounds like the differential but just want to be sure.
View 7 Replies
I have a 2001 Ford F-250 with the gas v-10. Yesterday it started just fine as always. Today I get into it and it starts to turn over just fine then starts to make a grinding sound and the truck won't start. I have had a fuel issue in the mornings with once it started you had to barely press the gass to keep it running. But never makes a funny sound and always runs fine. This only last for a couple of min and then it runs fine for the rest of the day. The grinding is not the starter. I took it off and had it checked and it was fine.
The truck had been using oil. When I checked the oil level it was low but it was still on the stick. "I know a motor needs oil to run smooth but it's my dads truck and well let's just say he is not the best on maintenance". Also I smelled the oil and it does have a gas smell to it. So it definitely does have some gas in the oil. I tried to light the dipstick with a lighter and it wouldn't light. So not sure how much gas is in it but that's what I did.
So the question is, would something just in mid crank go bad and then not let the motor crank. Truck made no weird noises before this so I find it hard to believe the barrings just went out in mid crank and now it is shot.
Also I just checked compression on front cylinders.
Driver side read 75lbs
passenger side read 100lbs
View 4 Replies
My passenger side front wheel is making a thump, thump, thump sound when turning. The wheel is smooth when turning, but when returning to straight it kicks everyone 1/32 of a turn.
I know my sway bar bushings are bad, but I doubt this would be caused from that?
Should I be checking ball joints, hubs? It's been like this for 2-3 weeks
2000 4x4 v10
View 14 Replies
I recently accidentally drove my Camry into curb in a parking lot. It was only a light, but since then I've noticed a grinding sound ONLY when turning right. Everything else seems fine. I looked under the car and saw the black plastic casing under the car is cracked and it looks like it might be grinding against the left tire, which could cause that noise. I've also heard it could be a bearing, but would that suddenly happen immediately after an encounter with a curb?
I do plan on taking it to the shop, but I have to wait at least a week until I get paid. I'm guessing that should be okay.
View 8 Replies
I've been getting a grinding sound when turning my car. The sound is especially noticeable when pulling in or out of a parking spot and when turning at low speeds. The sound I hear is reminiscent of an old bed spring compressing or an ironing board closing (maybe a bit deeper of a sound than that though). I took it in for service, and they replaced the strut tops. However, the sound returned the next day, and it seems to be getting worse. All parts in the car are stock.
View 3 Replies
Here is the issue with my car. It's a 1995 Honda Accord sedan, automatic transmission, inline 4. For the past 6 years or so, when you take a turn at a certain angle and a certain amount of acceleration and a certain amount of speed, it'll make something like a rhythmic grinding sound until you straighten the wheel and escape the turn. It happens far more often on left turns than right turns.
Adding to the oddity, say you are getting ready to take a left turn. Now if you are at a turn where the angle, acceleration and speed necessary to make the sound -- the sound can be completely avoided if you accelerate straight, let go of the accelerator, then use the momentum to turn, let the wheel straighten out to complete the turn, then begin to accelerate again.
A while ago I took it to a major repair center and they took out all the axles and some how concluded that it was the transmission. I really don't understand how it could be that, as the car shifts fine, and the sound never occurs when going straight. This past week, I took it to another mechanic, and he concluded that it was the axle shaft on the left side, maybe the axle shaft on the right.
So I had the left axle shaft replaced. I drove it home and didn't notice it, thought it worked; the mechanic himself drove the car around for hours after and didn't notice anything. Just to be sure, I take the car into a cul-de-sac that has the perfect turn angle to make the sound. Guess what, it's still there, albeit muted a little bit.
I am wondering if it's worth it to fix the other axle shaft, how it's possible that it could be the transmission, or if it's anything else that's possibly wrong. Again, this sound has been going on for years. I am completely frustrated and want it gone. I am thinking about making a video with the sound...
View 8 Replies
Drove about 10 mins and parked. Came back 5 mins later and wouldn't start. Starter click can be heard when trying to crank but doesn't turn engine. Checked fuse (#113) and starter relay - both are good. AAA came out and tried to jump but no success. Flat bed towed back to my house last night.
This morning, woke up bright and early to pick up brand new Napa Premium starter. Replaced it thinking that was it. No dice- same thing, 1-click, no turning of engine.
Batteries & terminals both good & clean. Hooked up 2 additional fully charged deep cell marine batteries via jumper cables and no difference. Voltage @ starter terminal = 12.4V.
When cranking, voltage drops all the way down to 1-2V if holding the key in the crank position (1 click and then nothing). Returns back up to ~12V when released.
Jumped pos terminal to starter solenoid, got clicking but doesn't turn engine.Is my tranny or engine frozen...?!
View 12 Replies
Recently (5-6) months my Gen II has been making some weird sound when I turn it on before the ICE starts. Also when I turn it off after the ICE shuts down. I really don't know how to describe the sound so I took some clips of it. Sort of a high pitched grind maybe? Car has 45xxx, just had the Hybrid water pumped replaced.
[URL] .....
[URL] .....
View 6 Replies
This started a few months ago. At first it only happened when making a hard right turn, its a repeated click or grinding noise. Over time it has gotten worse, and now happens when turning either direction, and its worse the faster the car is going. Turing into the parking space at our apartment is fine... turning from one street to another going to work is not. Various things I looked up suggested the cv joint, but when I went to parts stores websites to look up prices all it gave me was cv boot kits in the results. Is this whats actually wrong, and is it something easily fixed for a DIY person?
View 7 Replies
In the past few days, our car (2006 Prius) has begun making some louder-than-normal noises while driving. I've determined that the noise appears when you turn the wheel at all to the right (note: not just making a right turn...any degree to the right past straight is enough). It seems to be constant when the car is running, but really only becomes perceptible around 30 mph. The sound is sort of like a buzzing. Maybe a grinding, but not quite. It sounds like it might be similar to this issue (2006 Engine Noise - buzzing, especially loud on highway | PriusChat), but I can't quite be sure.
View 4 Replies
Got the stabilizer bar recall done in February and have been on a couple of long trips since then. No real issues until about a week ago I noticed at low speed, when turning left, and usually if there was a small bump or incline........like turning into my driveway, there would be a popping/grinding sound. It could happen at speed, but never heard anything. I go last night to install some ECS cross drilled and slotted rotors and flush spacer kit and noticed this on the left front....
Well honestly I noticed first that I needed to wash my car, just got back from the beach and it has been raining here, but is this installed correctly. The bar is bent near the top, easier to see in person and I am fairly positive this is not correct. Called the dealership and they are going to check it out Monda. The picture below is of a left front on a MK7 and it appears to be the correct.
View 9 Replies
So I just completed my hydroboost install and fixed exhaust manifolds. After this install the below problem started.
ISSUE: While going slow and straight no problems. Slightest bit of turning effort left or right makes a sound like a tire rubbing on leaf springs. I can also feel the vibration. It happens in drive while moving or in neutral while moving. Happens wither hubs in auto or locked. Happens in 2wd or 4wd. It's not the steering pump cause it wines a tad now when brakes applied and I turn steering wheel. So I know what that sounds like. Expected that.
Jacked it up and checked for any movement in steering or ball joints and found nothing.
X does not make the sound above 15 mph. It's annoying....sounds and feels exactly like tire lugs hitting the leaf springs but they are not.
View 14 Replies
I get a grinding or whirring sound when I turn my steering wheel left or right. I gets worse if press the accelerator pedal. I believe it has something to do with the power steering but I don't know how to troubleshoot the issue....
View 5 Replies
When I move the wheel to the left, I get this metal grinding sound (similar to rust on brake rotors/worn down brake pads). It happens when the foot is off the brake and ONLY when the wheel is turned to the left.
View 1 Replies
