What it is. After starting up u hear a quick grind noise for just a sec than it goes away. Is that the a/c. I saw the expedition have that problem and its nothing to worry about. Are we in the same boat?
View 5 RepliesWe took our Ex to a local business and got almost 6k worth of work done prior to our trip. This included specific instructions to inspect the brake systems and replace anything that needed it. The work done included new front calipers, pads, hubs, new xrf ball joints, new shocks all the way around including dual fronts, a 6.0 tranny cooler and all new fluids. I alook tried getting a magtec differential cover installed but was told it didn't fit.
Long story short, while on the road we began to notice a grinding noise occasionally on small bumps. In reding ca our rear drivers side brake pads basically disintegrated and we were stranded while BigO replaced both pads, calipers and one rotor. They also advised that the slide pins were frozen on both calipers. This had no effect on the other noise I described.
Now that we're home we went back to the original shop and explained what happened. The owner agreed to take another look at the truck but basically said he stands behind his employees. He admitted that they chose not to examine the rear brakes to save usome "3 hours" of shop time. He also said that the rear brakes would've cost the same regardless of if they'd replaced them instead of BigO.
When my wife pointed out that our family had been first of all put in danger and secondly stranded by his worker's shoddy examination. He then preceded to ask why I insisted on doing so much work to such an old, high mileage truck. I left our truck with him so they could see if the sound could be traced back to anything they worked on and off course they didn't hear it.
I'm going back there tomorrow to take him for a drive and show him the noise which I repeat only started after their work was done. Am I wrong to be furious and think this crap is completely bs?
Had a grinding noise in my front end, left side. Found the hub was bad so got it replaced. Now I still have a grinding noise that comes and goes. If I hit a bump, it starts the grinding noise but nothing constant. Had the front end checked and nothing was obvious. Was trying different things and when I put it in 4WD, with the switch on the dash, the noise goes away. What to try next?
View 2 RepliesBut I'm still getting a grinding/clunk noise and general loose feeling from the front end. The only play I can feel is when I grab the u-joint/knuckle and pull up and down on it. I also noticed the seal at the end of the axle shaft tube is not there on 1 side... would this lack of seal cause the looseness?
View 9 RepliesI have a 2010 XLT, 85K, just started having a horrible grinding noise at start up for about 2-3 seconds, then gone. Going to dealer tmrrw. Multiple people said, possible oil pump hydraulics, ??????. Whatever it is, they say its expensive!!!!!
View 3 RepliesDriving at hwy speeds and head a pop noise in front end. Stopped and couldn't find anything, heard it a couple of more times, still nothing found, now I have a grinding noise left front wheel. What the issue may be. 2001 Ford EX 4X4.
View 6 RepliesI have a 2009 Corolla with 67k on the odometer so it is outside of warranty. I recently found about the TSB for the grinding noise on start up and took the car to my mechanic to have it looked at. He said he wasn't able to do the job because he would have to do some sort of computer update (ECU reflash?) and he doesn't have the means.
My car is currently at the dealership, and they want around 1800 dollars, 1400 for the VVTI gear, and another 400 for a tensioner. I have a friend who used to be a Toyota mechanic, and he says he can do the work as stated in the TSB, but he's unsure if the ECU would need updating, and it does not mention anything in the TSB. So what I am wondering is if :
1. Does changing the VVTI gear actually fix the grinding noise? I was reading an old thread where members said it was still there after having the TSB done.
2. Does there need to be anything done to the ECU after doing the TSB?
I just purchased a 2012 CC-R 2.0T Manual. One issue I'm having is during a cold start, the engine makes a very loud noise that doesn't resemble a higher rpm that usually comes with a warm up stage. It sounds like something is grinding, followed by a vacuum/sucking noise. It lasts about 20sec and then idles normally. It only happens during cold start.
[URL] ....
I have a 99 Toyota Tacoma 4 cylinder. Just reached 200,000 miles this past Sunday. I did a cold start this morning and there was a grinding, metallic noise from under the hood. I turned the key bafk because it didn't sound good. Turned the key again and it started like normal and ran fine. I had a new starter installed last Thursday and now I'm wondering where this noise is coming from. Before I changed my starter, I had the bad starter symptoms in the last two weeks, slow to crank over, the whining airplane noise (happened 3 times in the last 3 weeks). But now, this new grinding noise has me even more worried. Does my engine have to get used to the new starter and what other issues could this be? The battery passed the battery test at Autozone, and my alternator is fine as i unplugged the positive and negative wires from the battery while was truck was running. I really really like my truck and am trying everything in my power to keep it running as smoothly as possible.
View 19 Replies2000 GTI MK4 200,000 miles
I have had a grinding noise during engine start up for a few month but had no problem is engine starting up so left the grinding noise problem untouched.
About two days ago both lowbeam headlights blew up and left signal blinker on headlight lamp cluster didn't turn on while rear left blinker blinked at twice faster speed. At the same time I began to have starter motor stall while starting up the engine!
Wonder if this is a problem involving solenoid as well.
I have a 2009 corolla S. no warranty. 59k miles. my car gets a grinding noise whenever i start it. this is the example of the sound.
YouTube ....
When I start my car (usually a cold start) I hear a TERRIBLE grinding-like noise. Other times it sounds like a shuffling noise. And then other times it's like its over-exerting itself trying to start up. I've taken it to the dealer many times as it's a 2014 Corolla. They have no answers. The claim it's just a characteristic of the car. I call bull. This isn't normal for any car. My car has a CVT transmission by the way. Could it be the starter? Spark plugs? Note: the noise is about 1000x worse in winter. Audio is attached in separate comment.
View 19 RepliesIt was having trouble turning over for a few weeks, getting progressively worse, but we just didn't have time to look it over. Well, it finally died--now if I turn the key a couple times we got a grinding noise but mostly just nothing at all. The lights, radio, etc all turn on though so we were sure it wasn't the battery. Thinking it was the starter, we pulled that out and took it down to Advanced Auto Parts, but they ran a test on it and said it was still good. So we put that back in the car and brought them the battery instead--they tested it and said it was charging and holding voltage but not amperage, and that, that would mean the lights and things could come on but it wouldn't have enough kick to actually start the car.
So, we bought a new battery, went home, and popped it in. Still, nothing. My friend says it's not the alternator because with a fully charged battery the car would start even if the alternator wasn't right (and would just die in a couple days, at which point you'd know you needed to replace the alternator) and my car's still not starting. The last thing we tried before we gave up for the moment last night was checking fuses in the driver's side of the car and also under the hood, the handful we thought could be related to the starter, alternator, and/or battery, but they all looked good.
The only other thing I read about online with Infinitis was that if the security system was activated it wouldn't start, however, while I noticed the light for it is flashing which I'm not sure if that was normal before or not, I THINK if it is activated it would be solid red, and at any rate, I tried what I read online to unlock it (put key forward for 5 seconds, then off, repeat 2 more times, then try to start) and that didn't do anything either.
I have an 01 Excursion. I tried to start it this morning and the radio and lights came on, but all it would do is make a really loud clicking noise. If the battery was dead would the lights come on? My friend who picked me up to take me to work also told me my battery connections needed cleaned...
View 7 RepliesI recently had TSB 0146-10 ( grinding noise at cold start ) performed and my cold starts are even louder now. My dealer screwed it up 2 times and I have to return again due to this noise, leaking valve covers, and lots of metal filings found in oil and filter? It seems to me Toyota has a big issue with the VVT cam gear on this engine and wanted to post a video of my cold start?
My vehicle is a 2010 RAV4 with the 2AR-FE ( 2.5 ltr ).
This is after 2 cam gear replacements and the dealer confirmed this to be the sound of a bad VVT gear.
YouTube
So we have had problems with the starter (and flywheel?) since we acquired the truck, these problems being that when we would go to start the car, it would make a horrible "grinding" noise a few times, but would eventually start up. Recently, the car would not start at all, and made no noise when the key was turned. Called AAA, they gave us a jump, and the truck started again. Assuming the problem was then with the battery, we replaced it as well as both terminals. The truck would still not start after doing this, no noise at all when key turned. My questions then would be, if the battery is not the problem, why did the truck start after we had a jump? I'm thinking it might be the starter, and if the starter was shot, would the truck have no sign of life when the ignition was turned on? Should i try and change the starter or is there possibly another variable? 1986 auto Toyota Pickup....
View 1 RepliesI have an '02 Taurus. For the last year or so it has intermittently produced a metal on metal grinding noise while failing to start up. I'm told this is due to teeth being missing on the flywheel between the starter and the transmission. It's taken as many as six tries to get the car going. But the car has always started in the end.
My questions are: Is the problem flywheel worth replacing at this point at this price? Is it likely to fail totally any time soon?
Also, might the March '09 replacement starter be implicated?
So my Nissan Xterra 2006 has started making a weird noise about a week ago. I haven't noticed any problems while driving it but id really like to figure out what's causing the noise. It routinely starts when I start up the car after sitting parked for a while. Example, if I start the car up to go to the store it'll make the noise but after turning the car on and leaving the store I don't hear it. The noise lasts just a little while and is loudest at about 20mph. So once the car is warmed up I don't hear it. I can't really pinpoint where it's coming from because the car has to be in motion driving forward for it to start. It sounds like it's coming from under the car. What it could be.
View 5 RepliesRecently I've noticed more that when we first start the hyundai in the morning or after sitting a while and we use the brakes it grinds/ squeals a little and then doesn't after about 2 or 3 miles. Is this something to get checked out or should I spray something on my brakes to lubricate?
My next step that I though of was to get a simple automatic car wash cause it's been a bad winter in Rhode Island and the street shave been flooded with rock salt. I figure that might cause some friction under the pads.
Sometimes when I start my car it makes a weird cranking/grinding noise for half a second. The closest thing I have to engine mods are my TWM short shifter, and my borla axle back exhaust.
The noise only happens after my car has been sitting there, parked for a few hours. So to bring it to Toyota/mechanic would be nearly impossible to replicate, unless I left it there for a while. And even then, the noise only happens sometimes.
Yes I'm pressing my clutch pedal all the way down. No I am not holding the key too long when starting the car. What it might be?
The vehicle is a 2000 Excursion 7.3 Diesel. I have never owned a diesel before....
First issue is that I have developed a hard start. It started last Saturday, and went from sporadically starting hard, to starting hard every time. I have 146,000 miles on her. She cranks strong, but will not turn over the first time, sometimes takes 2, 3, or 4 times. (Foot on gas pedal) I don't know if it's an issue of not getting enough fuel or what. Occasionally, even after she starts, it's very rough (shaking the whole vehicle, and acting like she wants to die) until I rev the engine and she smoothes out. After she smoothes out, there is no problem with wanting to drive, she's strong. If I kill the ignition, and start up immediately, she starts the first time, it's only after 10 minutes or so of being off.
My next issue is a clunking noise when I press the gas pedal. I don't know if it's the tranny, because she shifts pretty smooth for the most part, doesn't miss gears, etc. I could be travelling say 50MPH, press the gas pedal very little, and I can hear the clunking, and actually feel it every time I press it. (Don't have to be mashing the pedal, happens on very light presses as well).
I have the TS Performance 6 position chip, otherwise she's stock. I tow roughly a 7000 travel trailer every couple of weeks, never any problems before this.