its a 2000 limited 4x4, must have been in the snow a lot because it was from up north and is pretty rusty on the underside. my dad and i have tried everything to get these caps off but nothing will work. lots of pb blaster, hammering, even cutting the one of the four joints and trying to wedge something from the inside. If we cant get it could a shop do it? and how much might they charge?
View 9 RepliesI am replacing the ball joints on my 07 f250 4x4. got down to the removal of the shaft itself and it won't budge. What is the secret here. Have to go to work on monday, and the weather in Cleveland isn't going to be very good on Sunday.
View 10 RepliesI need to identify the part numbers for the u joints in the rear drive shaft. The guys at the auto parts store kept telling me I only need two until I showed them that there are clearly three. I just want make sure that I get the correct parts before purchase.
View 5 RepliesOur axle seal went out 2500 Miles ago. Its a light leak and just wets the axle by the U-Joints. Also our 4x4 hubs don't kick into action when they should. I have to put them in Lock to get them to work. That may be why the axle seal went out, because I just leave it in lock then drive thousands of highway miles. (I don't do that anymore now that I know what I was doing) Maybe the vacuum isn't working. Could they have anything to do with each other? I don't think they do. I'm not sure how the vacuum works. Maybe I just need to service the Hub? I watched a video on it that made it seem like cake. New hubs crazy expensive!
View 8 RepliesI have my front axles out to replace the U-Joints but they are rusted in there. Even the C-Clip is fused/rusted in place. I use my flat wheel grinder and ground out the C-Clips but the U-Joint caps wont budge. Been soaking in penetrating oil too. Any way other than drilling them out?
View 1 RepliesI noticed my '12 F250 has grease zerks on the front axle u-joints and was wondering how often you need to grease them ? My truck has 10k on it and while I was changing the oil tonight I decided to give them a few shots of grease until it started coming out of the joint.
View 12 RepliesI have noticed a few drips coming from the rear axle input shaft where the drive shaft connects. It has only done it once and there is no residue on the trailer hitch so I know it didn't dump everything on the road. If change this seal, how difficult is it and do you have any information which might make it easier.
View 14 RepliesCheck out the pics. 99 f250 4x4. I have a leak in my front axle shaft. It looks like it is coming out of the dust cap on the end of the front shaft. I am pretty sure it is differential fluid from the smell. Is there a seal before the dust cap? Is the shaft hollow with fluid in it? I thought it was just in the differential and if it leaks it is at the seals where the axle goes into the differential not at the otter end.
View 2 RepliesSo the other day I took my locking hubs out and cleaned them really good. When they were out I noticed I could grabs axle shafts inside the hub and wiggle them quiet a bit. Is that normal?
View 2 RepliesI took the front axle shafts out a couple months back and remember NOT seeing any differential fluid in the axle shaft housing. But then when I took the tire off tonight.. I noticed diff fluid leaking from from the axle shaft dust seal ?
1. I didn't think diff fluid flowed up near those front dust seals ?
2. That's a brand new dust seal so I'm guessing some debri must be in the connection causing the leak ?
I put new upper and lower ball joints on a few weeks ago. The front end is really tight after getting done. the steering wheel will not return to center. I feel like I am constantly on the wheel correcting. I had the alignment checked and they said it was good. I also put new 17" wheels and bigger tires on it at the same time.
We just towed our camper this past weekend and the truck and camper was all over the road. Is all of the above caused by new ball joints?
Check out the pics. 99 f250 4x4. I have a leak in my front axle shaft. It looks like it is coming out of the dust cap on the end of the front shaft. I am pretty sure it is differential fluid from the smell. Is there a seal before the dust cap? Is the shaft hollow with fluid in it? I thought it was just in the differential and if it leaks it is at the seals where the axle goes into the differential not at the otter end.
View 14 RepliesI am a new 6.7 owner and had/ have a 7.3 As I have been getting to know the truck I have been under it and noticed that the front drive shaft and axle are locked in. My hubs are switched to auto but I know on my 2000 7.3 when my hubs are on auto my front axle and driveshaft are disengaged... I'm wondering if the new 4x4 system is different. I know that can save on MPG
View 6 RepliesCan I re-use this shaft or is that ring around it no good. The ring is around where the bearing sits. It is a circumferential hump all the way around.
View 14 RepliesI thought that my front wheel bearing was bad but I removed it and it seems fine. The issue that I'm having is a continous vibration (noise) in the left front that gets worse with speed.The half shaft makes a noise at the point where the half shaft meets the steering knuckle and when I turn the shaft at the outer splines, the grinding noise is present. My question is, is the entire half shaft supposed to turn, even the outer diameter of it that would enter the steering knuckle, or is the shaft supposed to turn inside of that outer diameter? I hope I was able to explain my problem clearly/
View 6 RepliesI have a E99 F350 7.3L 4x4 I know some or most of you have already probably replaced this part and or pulled a front axle shaft out. So here is my question...In the pictures provided you can see what I think everyone is calling a "Dust Seal" and as you can see it is bad and making a very terrible noise when i hit a bump...I was wondering what parts I would need to replace this seal? I tried looking it up and just get lost in all of the other things....I have found write-ups for the axle being removed while changing ball joints but none by it self to just replace this seal.
[URL] ....
I have the subject truck and do my own oil changes. I see that the front end has sealed ball joints and doesn't require lubrication.
Do the universal joints on the drive shaft or any other components require lubrication? 2014 F150 XLT ....
For what it's worth I have been feeling a bit of a tug for 3 weeks. That's about 150 miles or 5 times driving. Installed new sway bar damper.
Pulling into the driveway the heard a ting, and look to find the inner seal of the hub spinning on the stub shaft!
An exploded view of this front end hub/bearing/brake assembly?
Noticed some spotting in front of the house, and saw some leaking coming from the driver side near the axle. I'm guessing it's the axle seal leaking. I recently switched in to 4x4 about a week ago, shortly after that I noticed the leak. I have a trip to San Antonio coming up in the middle of Feb, about a 650 mile round trip. Can I continue with the plans and get it fixed afterwards?
View 2 RepliesWell the old ball ball joints are out, new ones are in and now I'm working on removing gear assembly so I can change the inner axle seals. I've been trying to get it out. It haven't had much luck. I've loosened the cap bolts, prayed, pulled, hit, and still no luck. The only thing I've been successful at is screwing up the first few threads of the bolt holes for the passenger side cap. Tomorrow I'll be getting a tap and chasing the threads to clean them up. Hope I haven't screwed it up too bad. How to get the gear assembly out?
View 8 RepliesI need a vacuum fitting for the front axle..... Where I can get one besides a dealer ?
View 2 Replies