Ford Excursion :: Driver Rear Axle Seal Leaking Coating The EBrakes In Gear Oil
Mar 30, 2014
While diagnosing an issue with my ebrakes I found the drivers rear axle seal was leaking coating the ebrakes in gear oil, replaced the seal. Decided to pull the differential fill plug and check to make sure it was full - drained a good bit out pulling the hub to replace the seal. To my horror this is what I find when I pull the plug. First photo is as it came out on the magnet - second is after a clean up. What is it? I am almost afraid to drop the cover....
View 14 Replies
Advertisement
2005 4wd excursion. I have a leaking rear seal on passenger side.
I have the hub assembly off. I'm down to the spindle. My old seal came out in pieces. There's either a piece of the old seal or another seal on the back of the spindle.
Are there two seals? This what looks like a seal still on the spindle against the plate on the back...
View 1 Replies
So I have a 2004 Hyundai Elantra 5 speed. The driver side cv axle seal started leaking a few months ago and I finally got around to repairing it. Everything went relatively smooth until I got to replacing the seal...
The problem is, it will NOT fit over the cv axle. It just won't. When the seal is installed, not matter how much force I put on the axle it will not go in. Also, I even pulled the seal back out and tried to put it onto the axle out of the car and there is no way it is going on. This is the third seal (done the rounds to through the big name parts stores) and no go.
Now, some quick car back story, I generally do all of my own repairs, but over the winter in the midst of a family tragedy I had a friend (professional mechanic with a shop) do a bunch of work to the car. He replaced the boot and joint that goes into the transmission (he did not replace the entire cv axle assembly for some reason). What I am beginning to think is that he replaced it with the wrong part.
Now, what I am wondering, is this even possible? Is it possible that it could fit and work perfectly yet be wrong? This also appears to be what broke the original seal. The inner portion of the seal was totally blown out in a circle, but perfectly, like it was crushed or cut out, and I am wondering if this happened due to having extreme force applied to it (possibly when he reinstalled it?)
That, or is it just extremely difficult / next to impossible to get these seals on? Even with both parts out of the car, stretching and pushing down on the seal (oiled it up as well to see if that would work) with all my might yields no results.
The leak was not there for the first month or so that I got the car back and then showed up. I have put about 5k miles on the car since I got it back. With Monday quickly approaching, I am wondering if I should just blow the crap out of my budget and pick up a new cv axle? I could at least have them pull one and let me see if the seal fits, I suppose.
View 1 Replies
I have noticed a few drips coming from the rear axle input shaft where the drive shaft connects. It has only done it once and there is no residue on the trailer hitch so I know it didn't dump everything on the road. If change this seal, how difficult is it and do you have any information which might make it easier.
View 14 Replies
I noticed the other day after my truck was parked on a bit of a angle there was diff oil from the passenger side on the ground. reading a bit on here i learned the axle seals are way in the front housing close to the front diff. and yesterday driving a heavy load around my front brake driver side got stuck on a bit and over heated and was smoking, couldn't even touch the rim it was so hot. anyway about this axle seal i got the hub off right now but cant seem to pull out the axle assembly through the knuckle but i see i have to pry and most likely wreck that seal. Looking for a link of piuctures or how to replace the axle seals in the housing.
View 11 Replies
I took the front axle shafts out a couple months back and remember NOT seeing any differential fluid in the axle shaft housing. But then when I took the tire off tonight.. I noticed diff fluid leaking from from the axle shaft dust seal ?
1. I didn't think diff fluid flowed up near those front dust seals ?
2. That's a brand new dust seal so I'm guessing some debri must be in the connection causing the leak ?
View 4 Replies
I unstuck my front axles yesterday and while under the car spinning the front axles freely and enjoying my easy fix, I noticed a rubber seal (a thick squared edge round rubber seal) sitting loose and spinning freely. Its next to the axle joint, right before it disappears into the housing.
I'm guessing this is a dust seal of some kind. There is no fluid leaking out...
I'm wondering if I can just press fit this thing back into place or do I have to take the whole front wheel assembly (hub, bearing, axle, etc) to get the seal back into place.
I'm wondering if it broke off from a larger seal or if this is the whole thing? You can see how the seal isn't sitting quite straight. It actually just spins around.
View 9 Replies
99, F250, 4X4, V10, 72,000 miles. I have had the front axle seals replaced three times in the past 3000 miles, and the right continues to leak. My mechanic screwed up three times?
View 6 Replies
When I took my Saturn L300 to the dealer recently for its regular oil change I was told that my right front axel seal was leaking and it will cost me $580 to replace. This seems awfully high to me. Am I getting fleeced by the GM dealer?
View 1 Replies
I recently had my rear axle seals replaced due to leaking. Does the rear diff fluid get replaced on that repair since the rear diff cover comes off? Trying to figure out when my next interval for changing rear diff fluid should be.
View 1 Replies
I have an 04 Limited, 6.0 PSD, 4x4 which I need to replace the front inner axle seals, the right side is leaking out the shaft. I have watched a couple of YouTube videos on how it is done but would like to get some first hand knowledge and recommendations.
First, how important is it to check the backlash before beginning the removal of the gear assembly? Do I need to remove the pinion gear as well or just the gear assembly?
How difficult is it to get everything back on place once the seals are replaced? I have not done this type of repair before and am concerned I might miss something.
I am planning to replace all the ball joints at this time also, this was the primary reason for this maintenance in the first place.
View 8 Replies
I get my oil change at the Toyota dealership instead of Lexus and save quite a bit of money for my 2013 ES350. At the 30k service, Toyota technician said he noticed transmission fluid leaking at the axle seal." I was gonna show Lexus this at some point, or maybe get an oil change there at the 40k service.
View 3 Replies
I noticed pool of oil yesterday morning, felt engine oil has leaked. Did oil change as it was due, the mechanic said the leak doesn't seem big enough, still overnight there was again lot of oil leaked, I kept a pan below to capture it. Checked it at auto shop near me and they said it is transmission fluid leak and probably due to driver side axle seal leak. I am going to take it again tomorrow to fix. How much do you think it will cost to fix if this is right diagnosis? This is 2005 4 cyl Ford escape with 150k on it. As per them if it is axle leak it will probably more of labor (2 hrs) than seal price.
View 11 Replies
Passenger differential axle seal is leaking again. It was replaced twice already. My mechanic checked the seal...its not damaged. Its not a excessive leak. Both times, the seal were replaced with OEM. I don't want to buy another one and replace it.
Its a 1995 Celica, 5SFE, 5-speed MT. 98k miles.
View 4 Replies
I have replaced my cv axle and seal, and now I have transmission fluid leaking from the axle seal. What could be the cause of this? The seal is brand new as is the cv axle. Could it be that it the seal isn't seated correctly? What could possibly went wrong to cause this?
View 3 Replies
Picture if you will...Removed tire, caliper and rotor. Removed hub, and knuckle containing the stub shaft/spindle with it's yoke for the U joint. You are now looking at the end of the axle tube, with the axle shaft in it, one end connected to the differential carrier, the other end has the yoke for the U joint on it. Just inboard of the yoke, is a seal. Apparently it's called a "dust seal" is there a bearing behind this, or is the first bearing all the way in at the differential? When I was doing my brakes, I noticed the passenger side u-joint is shot, and the axle wiggles around in the dust seal. Figured I'd replace the seal while I was doing the U joint. Also, how do I get the axle shaft out? Just pull, or do I have to remove a C clip from the inboard end? What is the right National part number for the seal? I have a 6/2000 Excursion.
View 2 Replies
Do I need a special tool to put the outer axle seal on a 2003 excursion? I could make one if I new how far down it needs to be. I'm replacing the needle bearings in the back of the hubs and it looks like the last seals were not on far enough and the hub tore them up....
View 13 Replies
How do you replace the rear axle seal in a 1995 F150?
View 14 Replies
This is a photo of my '79 F250 4x4 rear axle (Dana 60 full floater) this seal will leak in a few miles ..what I need is the part number of a replacement seal made like the one in the lower photo ..it seems that Ford no longer has this seal.
Notice the increased distance from the bearing to the sealing lip in this photo ..the sealing lip on the new seal in the upper photo lies almost on the bearing, this one just barely engages the seal surface on the axle stub. I can machine the bearing pocket deeper to cause the seal to move farther onto the sealing surface, but that would also cause the bearings to be closer together, and may cause problems there.
View 5 Replies
Well, the ac in my truck has been less than exciting since I've owned it and its time to address it before another trip.
I crawled under last night to explore the Ac clutch air gap and found that the shaft seal is leaking and clutch is grooved pretty bad and covered in oil.
I'm thinking it's time for a compressor, clutch, orifice tube, expansion valve and reciever/dryer. Does that about sum it up? I haven't messed with AC systems much outside of my simple jeep system that was as easy as two seals and recharge in my garage to fix it.
Do I need to flush the lines out? Should I do that at all? Motor craft worth the cost over something like four seasons? Its almost twice the cost but in the end if something goes I'm further downstream after freon etc to charge it and the possible shop charge if I pay to have to done.
View 4 Replies
What the exact part number is for the seal for the rear axle in a 2003 F150 4x4 ?? Mine decided to leak yesterday and so I looked up Ford for the part but there's two .. one is thick and one is not. I don't want to take the seal out first to look because I got no other vehicle to get it and putting it back in and out would be silly.
View 4 Replies
