Just put new tires on my excursion 4x4 powerstroke and I'm getting cupping just on the inside of both front tires it already has new ball joints and steering box tire rods are tight and all joints in the front. what else could cause it?
View 1 RepliesWhat is the cause of my New Tires are starting to Cup and or Feather pretty bad. Is this a aligment issue? Camber? I am just not sure because it feels like the truck drives Normal...
View 9 RepliesI have been "fighting" a front tire cupping problem on my L99 F350 Dually 2wd since I have owned it.
I got LOTS of paperwork with it, one of which was a service ticket from the dealer where it was bought new (with VERY low miles on it) saying several passing motorists had informed them that the front tires were bouncing down the road.
I have read this service complaint several times and I now feel that has something to do with it. I bought the truck with 70k on it some 8 years ago-the PO had installed EXPENSIVE Michelin XPS Rib steering tires on it and they were already destroyed by cupping.
I replaced all 4 shocks, and all 6 tires, begged the folks to FIND something wrong/loose/worn out on the front suspension/steering and they found nothing, they aligned it. THAT set of Cooper Discoverer HT tires did exactly the same thing, except I spent a lot of $$ having the tires rotated.
Now I have a set of Firestone TransForce tires on it and its been to a HD truck shop where I begged them to rip into the front end and FIND something wrong-THEY DIDN'T. THEY installed camber bolts and aligned it, yep, you guessed it STILL CUPPING!!
So, now I'm thinking is it possible that the wrong coil springs were installed at the factory causing this bouncing that the original owner reported to the dealer? I have now destroyed 2 more tires and getting tired of it.
I had my car drop for a while now on megan ez coilover. Before I bought my new set of wheels, I drove the car with the OEM wheels and they never had any cupping issues. Then after I bought my AME Shallen with 20mm hub centric H&R spacers on Nankang NS, and then they started cupping on the front inside tires after 5000 miles. I had the alignment done and only had the toe adjusted.(don't have camber kit) At first i thought it was the spacers causing the issue, but then I bought Orden's with new Nankang NS and had the toe adjusted to spec's again. Camber is at -3 BTW. Recently i started hearing the same road noise so I inspected the tires and found it was cupping in the front again! I also checked the front end of any damage or worn out bushing and couldn't find any signs of damage. I always keep my tires at 40psi, torque them down evenly, and I'm using hub centric rings. My questions is do you think is the Nankang tires or do I have a suspension problem?
View 2 RepliesI have an 04 ranger with 31x10.5x15 mud tires on it and the front tires are wearing on the inside real bad if you look at it the tire look tilted in on the tops...
View 1 RepliesMy tires are cupping on my Azera. I've had the tires rotated every 7500 miles as required by the maintenance schedule. The tires make a lot of noise while driving, especially at highway speeds.
View 25 RepliesGetting new tires very soon. I noticed this wear pattern on my front tires. The heavily worn part is on the inside of both front tires. Is this normal wear for our cars (I do go around the turns pretty fast) or should I have an alignment done once the new tires are on?
The link might not be working, try this one? [URL]
i have noticed that my front tires are wearing quicker on the inside. that is to say they don't seem to be wearing evenly. have almost no tread left on the insides of front tires and these tires only have about 13000 mi on them. is this and aligment problem? dealer says no.
View 4 Replies" Michelin LTX A/T 2 Load range E tires that are size 265/75/16"
I don't haul much and I don't tow.
How much in the front tires and how much in the rear?
I recently purchased a 2000 Ex Limited 2wd. It is stone stock except a slight lift. This lift gives it a pretty significant rake that I'm not a fan of. I'd like to get this thing leveled out without spending a fortune and I believe that would require the knowledge of the FTE.
The pictures below show the rake and existing suspension mods. With 285/75 16 Tires there is about 6" clearance from tire to fender on the front and 9.5" in the rear. It has a 2" spacer under what I imagine is the stock front coil spring and a 4" block below what do not appear to be stock leaf springs (guessing because the anti wrap spring is not present).
I'd like to get the front end to sit about 3" higher than it currently is to better match the rear. Lifts of any type are foreign to me. What front springs (and other components) do I need (and what brands would you recommend based on hard earned experience) to make this thing work?
Just bought a 2001 v10 ford excursion limited with 127xxx miles. I have a few questions.
1. I can't get the front tires to rotate while parked and stepping on the brakes. I thought it was caused by the 35 inch BFG goodrich all terrian tires and a lift kit i dont know how tall but apparently i'm just a sucker. From the searches i did, i think the problem is that either the power steering or brakes doesn't have sufficient pressure to power both at the same time. what is the fix to this?
2. I found metal shaving in the rear differential. For lack of picture, the best i can describe it is that it looks like shaving off an ice block. Also, the fluid is gray and consistency of sludge. I searched and some said the shaving is normal and others said fix now. Which is it? I assume that the rear differential fluid needs to be changed.
I have a 2013 F250 6.7 Crew Cab Single Wheel. Stock 20" Michelin tires and stock suspension. I have almost 20K miles on it. I just rotated the tires again and noticed that the rears are worn down on the inside. The fronts look perfect.
View 11 RepliesI destroyed my front tires about 3 months ago, I thought the tracking was out because the inside of the tires were all chewed up, so I bought 2 new ones and had the tracking done. Well today I took the .:R to the Tire Barn for a rotation and they informed me that there's wear on the inside again.
IWould it prevent any more damage to the tires if I replaced the front control arm bushings and had a new alignment done? Ideally I would like to replace the control arms but I can't afford that right now as I'm about to buy a house.
'02 SC430 with just over 30K miles. She is wearing out the inside edges of the tires. We have had the car aligned twice in our one year ownership. Are these cars prone to this kind of wear and/or going out of alignment? Would this be a spring/shock/strut issue? I assume the original components are still on the car so maybe she just needs replacement parts due to age. She has low miles, but she is 11 years old now.
View 14 RepliesHow much air pressure should you run on 305/70/16 tires?
I had tires rotated and the shop had them at 35psi. That was just too low and didn't drive well. I have about 42psi right now and they drive better.
I've heard everything from 35-50psi.
What do you run?
Four months after I bought my Prius III last year, we discovered that the left rear wheel was so out of alignment that it ruined the tire in 5,000 miles, and then also ruined the one put in its place during regular tire rotation. Toyota replaced the entire set of tires, and I checked the alignment this fall and again this spring when I took off the snow tires.
Everything looked fine. Nevertheless, when I rotated the tires today, the tech reported that ALL FOUR tires were substantially cupped on the inside, after only 6,000 miles on this set of tires. Road noise has become much higher. It doesn't make sense that all four wheels got similarly out of alignment in just two months.
Had the tires balanced, still shakes. Had them balanced and tires rotated on the wheels for optimum placement. Still shakes, no visible bubbles for tread seperation. What to check next?
View 6 RepliesI have an 05 Excursion Eddie Bower. Ordering new tires tomorrow and trying to figure how large of a tire I can fit on my factory rim without any issues My Excursion is completely stock!Going with the BFGoodrich All terrain K02's. I was going to go with 315/75R16's. Is that too big? Will I have rubbing issues? Will that fit the stock rim without any issues? Or how about 285/75R16's if the 315's are too big?
View 14 RepliesMy Excursion only has 74000 miles and I just replaced the original shocks with Monroe Reflex and combined with my Goodyear Silent Armor tires was running beautifully. Then after a "deal" from Ford, I replaced the Goodyears with LTX-MS2's and had the alignment checked since my Goodyears did have a little cupping after 45000 miles. They also checked all the front end components and said that everything was in good shape! Upon driving it home, the Excursion steering was extremely loose and I was ready to return the tires and get new Silent Armors, but I figured that there probably was something screwy with the alignment that they just did. So I brought it back, test drove it with the tech at 75 mph and he decided he needed to recheck the alignment. After the realignment, it drove beautifully, but after reading the posts on various forums regarding the proper toe-in on the front, I am questioning whether the alignment is set properly?
After the 1st alignment (in degrees):
LF Camber .3; Caster 3.0; Toe .01
RF Camber -.2; Caster 3.2; Toe -.03
Total Toe -.03; Steer Ahead .02
LR Camber .1; Toe .12
RR Camber -.03; Toe .16
Total Toe .27; Thrust Angle -.02
After the Realignment (in degrees):
LF Camber .3; Caster 3.0; Toe -.03
RF Camber -.2; Caster 3.2; Toe -.04
Total Toe -.07; Steer Ahead 0.00
LR Camber .1; Toe .13
RR Camber -.3; Toe .18
Total Toe .31; Thrust Angle -.03
The stock 265/75/16 tires need to be replaced and I was considering swapping 285's on the stock wheels. Will I notice an increase in fuel consumption? I realize that calculating mpg will need to be adjusted due to larger tires since the speedometer will be slightly off.
View 14 RepliesSo just bought an 2001 Excursion XLT 3 days ago! Truck only has 43k. The motor is 6.8 V10. So driving home the other night I noticed all the lights inside and out are flickering!! No battery light at This time. So here's what I did so far had the battery and alternator tested and everything passed. I've read some forums and heard the alternator may pass and still could be the issue... so bought a new one well even with the new one no luck. BUT if I unplug the alternator while running the lights no longer flicker.
View 14 Replies