Ford Excursion :: Cruise Control Will Not Work / Deactivator Switch Is Open Or Circuit Defective
May 24, 2012
I bought a 2002 Excursion 2wd V10 at an auction with 105,000 miles. I've been working through the little problems and I'm down to one last small item.
The cruise control will not work. I found a thread to diagnose the problem. My diagnosis is:
After doing the self test I received: 3 flashes - deactivator switch is open or circuit defective.
What does this represent and what shall I do to correct it?
View 11 Replies
Advertisement
Just got my first X(and Ford) a couple days ago. Anyways, the cruise control doesn't work. I checked the CC switch on the master and it tested fine and I installed new switches on the steering wheel.
When I do the self diagnostic test with the steering wheel switches they all test fine, and on the last button(set) it lights up, but no other flashes. What does that mean? In 1 thread it stats that 0 flashes is the speed control servo.
View 14 Replies
So noticed my cruise control does not work when I turn switch to on position the green light in cluster does not come on what are some problems that I could look into and also any example of using turn signal Bulbs in the head lights as drl lights instead of it running off of the actually headlight bulb?
View 9 Replies
I just discovered my cruise won't "SET" (light goes out after 1/2 second) anymore after having the brake light switch done yesterday.
View 2 Replies
The cruise switch on my brake master cylinder is bad and causing the cruise to not work. I have it bypassed with a jumper wire and it works fine. is there any reason not to do this?
View 11 Replies
I have an 02 f150 5.4 and since I got it it hasn't had cruse control. I went to a local ford dealership and they ran the vin and didn't find any recall on it. Under the hood on the master cylinder there is brake fluid coming out of the brake control switch. Would I have to do something with the harness too?
View 9 Replies
I'm at my wit's end trying to install cruise control in my 2009 Corolla. I thought it was a relatively easy install, but then after putting the airbag in place, I find that the horn no longer works. I test out the cruise control, and the green "Cruise" lights up on the dashboard..but it doesn't actually work.
View 9 Replies
Where to decipher engine codes? I pulled a P0001 Fuel Volume Regulator Control Circuit Open code .
View 11 Replies
My Phaeton has been running perfect since I got it. Yesterday I took it to the dealership to get fluids topped off and a wash. We have had a break in the weather the last couple of days, so I took my w12 on 465 and got it up to 120 before I chickened out. It continued to ride perfectly. This morning when I went out to start my honey do list the service engine soon light was on, it is still running perfect, but when I stopped by local auto store and had them pull the code it says "thermostat heating control circuit open". My middle temp stays at 200, when sitting still the left temp gauge goes almost to 200 however when driving it falls to under 160.
View 24 Replies
My scanner reads P0001 Fuel Volume Regulator Control Circuit Open. My truck shuts down without warning, runs great otherwise. I've changed 2 grey CPS units and now have the Black IH one installed. What the Fuel Volume Reg.is? Is it the IPR on the HPOP?F250SD 7.3 225,000 miles.
View 10 Replies
I have a 2002 7.3L and keep throwing a P0683 code (Glow Plug control module to PCm comm circuit). I have looked though all the Forum posts I could and it looks like the GPR, or the GPCM, or harness are at fault. I know my truck has the GPCM ... does it also have a GPR? I am not getting ANY individual GP failure codes, but the damn thing is having a hell of a time starting in the cold.
1) How do I determine if the GPCM is bad?
2) If I have a bad ground?
3) Bad connector to GPCM connection?
4) If something is wrong with the wiring harness itself
Last night I unplugged the harness from the GPCM, cleaned the connectors, added di-electric grease to improve the connections .. made no difference.
View 4 Replies
I finally got around to trying to fix my inop cruise control. Did the self test and got a flash code 2, BPP switch. I replaced the switch but its still inop and still have flash code 2. Got my meter out and started checking system.
I found the fuse in the deactivation switch recall harness was bad. I removed the harness and plugged the two remaining connectors together and the cruise works. I returned home and unplugged so it wouldnt short out. The connectors are clean and no signs of fluid.
Says on jumper harness that the fuse isnt serviceable and to replace with 9F924 harness. Well the fuse is serviceable and the harness ohms out good. Is there a need to buy a new harness or would I be ok with a new 5 amp fuse?
View 10 Replies
I have a 2001 ford focus SE and l can't get the cruise control to work anymore, is the problem a fuse and if so where is it located or a problem with brake pedal?
View 6 Replies
I own a 2013 C-Max hybrid and I notice that during long drives if i engage the cruise control, I don't get as many EV miles as I do when I have my foot on the gas pedal and take it off when i have reached my desired speed. Does EV mode not work in cruise control? My feet start to ache a bit with constantly having to press and release the gas pedal just so that I can generate some EV miles.
View 3 Replies
I had a reputable repair shop briefly check out the cruise control on my Aerostar cargo van. They said it is not because of a vacuum leak. What is most likely the problem?
View 11 Replies
On my in laws 2000 explorer the cruise control does not work. When driving and activating the cruise control (on, then set), the cruise-control dash light comes on for a fraction of a second and goes off again. Tried it at freeway speeds.
Any clue ? I heard there is a separate brake switch for the cruise control and one for the brake lights. The brake lights operate normal. Could it be the other switch ? If so where is this switch ? Under the dash or under the hood ?
View 7 Replies
The cruise control switch on my 2000 Ranger just broke. It looks like you have to remove the airbag to access it. How is that accessed? It looks like there are 2 plugs on the back of the wheel that need to be removed.
View 9 Replies
Ok replaced the front brakes, tie rod ends, and all ball joints today. Also flushed old brake fluid and replaced with new. Now my cruise control does not work. Light on the dash momentarily flashes when I try to set the speed. I have checked all the fuses and the connections and everything appears normal.
2001 Ford F150 5.4L 4x4 off road pkg stock height and tire size.
View 7 Replies
I recently got an Escape and I am having a issue with the cruise control. That being, it doesn't work. The control module under the hood is all hooked up, the linkage the the throttle body and all. No broken cables.
The brake lights work as intended, and only when the brake is applied. On the inside, the dash-light cruise indicator works fine.
I ran the diagnostic by holding the off button and turning the key on. The cruise light flashes and I begin the sequence. I noticed I was pushing the brake out of habit while running the first few tests. They all returned 2 flashes upon completion of the diagnostic. All other buttons were registered.
Now the strange part, when I took my foot off the brake and did the same test, the final result is three flashes of the cruise light. I understand these flashes represent a fault, and I am having a hard time as I cannot find one.
What do these results mean? I'm thinking the brake being applied gives a fault surrounding the fact that cruise is disabled when the brake is applied.
View 3 Replies
I turn my cruise on and then attempt to set it , nothing happens , doesn't set, no light , nothing. I hit coast and the light comes on but still doesn't hold. Should the light come on when cruise is turned on or set? I checked the master cylinder switch and it's not wet. I also did the self diagnostic test and got nothing but the initial first light blink.
View 4 Replies
New problem with my 99 f-250 superduty supercab 4x4. Cruise control does not work. Checked all fuses and all are good. No cruise light or speed cont light . Where do I start? What do I need to look for? Where do I look?
View 4 Replies
