This past week I changed out the front wheel bearing hub assemblys on both sides. I'm curious if completely disassembled one of the units? If so what did you use to get the large nut with the 4 notches in it off?
View 2 RepliesI have been having towing with the X. I have been getting a growl lately sounds like the front left wheel bearing. Today I jacked it up and did the wiggle text. I have a very slight wiggle in both wheels. Is a slight wiggle normal? I know the bearing on the left is more than likely gone as the growl goes away when I jerk the steering wheel. But I haven't heard any noise from the right side yet.
View 14 RepliesMy Excursion has proved to be a reliable winter vehicle, as was the intention. A few weeks back, at 116,000 miles, the right front wheel bearing started to squeal around left turns. Not very loud, so I didn't think it was all that bad, just an indication it was going. I jacked up the front of the truck anyway for good measure, and found a tremendous amount of slop in the bearing. Yeah, the bearing had disintegrated. Time for a replacement.
I bought a new replacement hub off of eBay, and proceeded to start tearing into the thing. Should be an easy repair... Right.
The repair itself is actually straightforward, but I had a few little snags get in my way. The one I'm facing now is that the new hub did not come with replacement studs, and the old hub's studs will not come out. Yes, I tried using a torch (and failed). I got one removed, only to find it's a fine thread and possibly Metric. Either way, it's not something that they have at Lowes.
Where to get more of these, or what the size is so I can order some from McMaster?
How can you tell when your wheel bearing/hub assembly is going bad? I am hearing what sounds like "metal-on-metal" and I've already changed the brake pads, but the sound still persists. I was thinking about changing out the brake rotors since I did notice an inch long score on the rotor when I was replacing the pads. I don't want to spend a couple hundred dollars on rotors to find out it was my wheel bearing/hub assembly all along.
View 8 RepliesI have 2012 Impala and hit a pot hole blowing out the left front tire but rim was not damaged, replaced the tire. Now the shop tells me that the wheel bearing has been damaged and the hub/bearing assembly needs to be replaced. I've never seen this happen. Is it possible that the bearing got damaged?
View 11 Replies2001, F250, 4x4, 432,000 miles...
Seems this truck eats up bearing assemblies. Its like every 2-3 years, I'm having to replace one side or the other. And we talking like 30-40,000 miles....
BTW.... although I'm not out doing much 4x4 driving, this truck does do a lot of dirt roads, probably over 50%...
I'm attempting to replace a front wheel bearing and hub assembly on a 2004 Chrysler Sebring. I've removed all the hub bolts and all other more external components. I've tried hammering the assembly, reinserting the bolts partially and hammering those, a slide hammer, liquid wrench...
View 9 RepliesI have removed knuckle assembly and pressed out bearing hub assembly, I have the new bearing hub assembly..... I live in Iowa so there is corrosion on the knuckle assembly - I have removed enough that the new bearing assembly will go in....
My question/concern : With the corrosion removed the surface of the knuckle where the bearing will seat is not uniform all the way around. The bearing hub assembly will go in and will require pressure to do so but will the bearing last? I can buy a steering knuckle but do not want to if I don't have to.
My wheel bearing in the rear went..as its roaring when driving and shop told me wheel bearing needs replaced. I am a bit handy. Is it a big job to change a rear wheel bearing on a 2002 ford escape 3 litre. What tools would I need...don't need a press for wheel bearing on this model, not sure....
View 1 RepliesNeed to change an 02 front wheel bearing. Can the the bearing be replaced without taking hub off? It slides or presses in.
View 4 RepliesNot my video, but I have the same exact sound coming from my passenger side wheel on my 03 V10 4X4, 130K. Passenger side only, no noise from the other side.
YouTube .....
Before I spring for the Timkin, does this sound like a bad bearing? No play in the wheel, but it's a clicking sound.
So on my girlfriends 2000 echo I get the classic bad wheel bearing noise/vibration on the front left (driver side) wheel. Worsens under load (right turn) and goes away when unloaded (left turn). I've replaced left side bearing, CV axle, brake rotors/pads and the noise still persists. My next thought is maybe the ball joint but humming/vibration tells me something out of rotational balance. Bearing in the transmission? I don't know. I'm stuck.
View 5 RepliesI have a 03 explorer with approx 160k, I am experiencing a thumping noise while driving. It gets worse on right turns and gets better on left turns. initially i thought LF wheel bearing so i ordered a hub assy and replaced LF. noise is still there. I guess, thumping noise caused by wheel bearings, i know its usually a grinding kind of whirring noise.
The noise doesn't seem to change with accel/decel so I don't think it is driveline related (diff, drive shaft etc.) should i bite the bullet and replace the rf as well??? I should also mention that there is also a shake in the steering wheel that seems to coincide with the thumping (i.e., my hand shakes along with the thumping, and the shake gets worse when the noise does)...
1999 explorer Eddie bauer. Front wheel bearing nut size? 33mm?
Looking for a torque spec procedure. Need to replace an abs sensor. Sensor alone was 120 bucks so just bought the whole hub assembly with sensor. Might just put the whole thing on.
Is there a good thread for a complete socket size portfolio on the explorers. Thinking sizes over and above normal socket sizes found in your typical socket set?
My wife's Explorer 4x4 has a noise in the front at around 100km/h. It is not detectable below 90km/h. Its not noticeable from a standstill until around 100, then you hear it a little. I find I can make it more noticeable if I vary my speed from 110 to 105 up and down, then its easier to hear. Once you get below 90 km/h you cant hear it at all.
I have a broken leg right now, and I normally do ALL my own work so I'm a little-limited mobility wise at the moment.
I'm suspecting a wheel bearing. I put the Explorer in the garage and my son jack up both wheels on the drivers side. I started the engine and SLOWLY accelerated up through the gears to 100. I know the hazards with this as I've done it with other vehicles, but this was the first 4x4. Then we jacked up the passenger side (after lowering the drivers side) and did the same thing. I could slightly hear/feel the rumble when the passenger side was jacked up.
I did drive the vehicle on my outdoor ramp/pit so I could use my crutches and get underneath to have a look. I grabbed the cv axles and they feel solid. The propeller shaft was replaced last year, and the cv axles look brand new. (bought the vehicle off a friend two years ago.).
So, are my suspicions correct, is it the pass. side wheel bearing? The Explorer has 294000kms. Never did test it on corners as I didn't want to swerve back and forth on the highway with the amount of traffic.
What is causing the right front wheel bearing to keep going bad on my 06 f-150 2 wheel drive....
View 1 RepliesI'm working on a 02 explorer. The front end is howling so I replaced the left side and no change. The howl goes away when braking. Is it the right side then or something else? I replaced both front brakes pads so it's not that.
View 2 RepliesRepeat Front Hub Failures -- 2WD Try this situation -- Purchased 2006 F-150 XL with 57,000 miles. Truck built on 05/24/2006.
Sept 2011 68,621 miles -- Left front hub failure -- Wheel bearing grinding -- Done by Bell Ford in Phoenix.
2013 -- Left front hub failure -- wheel bearing grinding -- done by independent shop.
Sept 2014 -- Left front hub failure -- wheel bearing grinding -- done by independent shop.
Sept 2016 -- Upper & lower control arms, struts, strut mounts, springs replaced -- Quality part used -- Complete front end alignment -- Brake job front and rear.
Nov 2016 -- New performance exhaust system due to exhaust leaks.
Dec 2016 -- Failed automatic transmission -- Remanufactured FORD transmission installed w/ 36 mo warranty. Sanderson Ford gets an A+
March 16, 2017 151,000 miles -- Left front hub failure -- wheel bearing grinding! Verified by jacking up truck and spinning left front wheel -- GRIND! This is coming from down in the hub. This is a 2 wheel drive truck. Yes, you counted correctly, this will be the 4th replacement on the Left side!
NO Towing! NO Overloading! Wheels are 2006 XLT style Aluminum rims with P235/70R17 Michelin XLT M/S (Defender LTX) tires all around.
It only hauls maybe 200 to 300 pounds of electronic equipment at the max, once in a while. This is driving me crazy! I always use FORD PARTS for the HUB ASSEMBLIES. Really loosing faith, the front right hub is OEM original - NEVER CHANGED!
I had my front driver side wheel bearing blow on me, out of nowhere, while doing about 70mph on my '03 Supercrew 2wd. it really destroyed my spindle and rotor. i replaced everything from the spindle out (rotor,pad,caliper,caliper mounts, bearings,etc). I packed the bearing really good and put it all back together. Well, it happened again, same thing. Doing about 70 and it just blew out of nowhere. Why it could be happening??
View 14 RepliesI have a 94 Explorer. I recently swapped over from auto to manual hubs. I followed a detailed write-up that I found online. During the process I repacked my outer wheel bearings. Ever since then I hear a grinding noise coming from the front wheels. Sounds like the bearings aren't seated properly. The guide that I followed instructed to torque the spindle nut that sits next the the outer wheel bearing really tight in order to seat the bearing, then loosen it back up and hand tighten it. But when I loosened the spindle nut the wheel bearing would pop back out. What is the best way to get a wheel bearing to stay seated properly?
View 2 RepliesIt's time to replace my axle bearing and hub assembly. Looking at RiffRaff site they show 3 different models. Early 99, fine course and course. I think I have the course thread but just want to make sure before I order. My truck is a L99 and I don't have the abs sensor. Looks like all 3 have come with the abs sensor. Do I simply not connect the sensor? Here's a pic of what i have. Course thread?
View 3 Replies