Ford Excursion :: Addition Of Backup Sensors On Chrome Bumper Without Drilling
Mar 17, 2016
I'd really like to add these to The Beast, but don't want to drill through chrome. My bumper has some plastic running along the top (see pic). Just looking for info for the same bumper mounted the sensors there with success.
View 9 Replies
Advertisement
My Excursion had a mangled rear bumper when I bought it recently. I just bought a salvage one to replace it. I had it installed today. I want to salvage the backup sensors in the old bumper along with the license plate lights. How do these come out? They seem locked in there to me.
View 3 Replies
Is it possible to turn off the backup sensors on my X ?
When I am towing these things drive me nuts!
View 14 Replies
Just started doing this. Sometimes I can get them to turn on in I hit the button enough. Switch going bad?
View 12 Replies
I can't find any info about this "always on" reverse light issue. My searches show that most people with the problem only have it when they put it in to revers. Mine's broken but the light is on all of the time indicating it's not working.
I can go through the sensors, but I think the system only recognizes sensor failures when the car is in reverse. What's my first/next step?
View 14 Replies
Ok, so it seems I have 3 bad backup sensors on the 2002 Ex. Background information for those considering a repair:
I put the Ex in reverse, key in run and can hear "fast ticking" from only one sensor. Sensor removal is easy (at lease on the two outside sensors). Two tabs on the black housing in the bumper hold the cylindrical sensor in place. Release the two tabs and work the sensor out. I haven't tried to remove the bad inside sensor yet as there is a lot less room to work there.
Once removed, a single tab on the wiring harness connector holds the sensor in place.
Here is the problem I have. I can't get the sensor to LOCK back into the connector. I have backed the connector against the bumper and pushed on the sensor with all my strength and I cannot get it to lock back into the single tab on the connector.
Is there a trick I am missing? I am ready to try vice grips but I fear I will damage the connector.
View 7 Replies
Looks like a great option the Job 1 trucks missed out on. Looking into the feasibility of it. This is my first Ford so I am not really sure how the factory plans these things out.
View 14 Replies
Any good way to install and mount a light bar without drilling into the front bumper or grill? I have a 32" LED bar I want to mount between the top of the bumper and bottom of the grill, but the mounts aren't ideal for where I want to put the light.
View 9 Replies
How are you going to remove the chrome strip on the rear bumper. Mine got damaged and I need to replace them with a new one.
View 5 Replies
Looking for a DIY for this part? It is part number 5 in the illustration.
View 5 Replies
I have a 2002 f350 that I have changed relays, control unit, checked fuses with no change. The hazards work normally. I'm ready to drive it off a cliff. I was told that it could be a bad ground. But no one can tell me where the ground may be. I have looked at the wire run from back to front with no problems found.
View 1 Replies
I was searching for instruction how to replace the chrome trim that appears to be a seperate piece of trim on the rear of the Phaeton. Mine has some issues on the passenger side and would like to remove it to have it either repaired or replaced.
View 11 Replies
How to remove the chrome trim around the fog lights and the chrome bars beside them I have a 2014 SE
View 2 Replies
I'm going to be installing an 8" lift on my excursion and I would like to add a rear sway bar.
I cannot find any info on the hellwig if it works with lifted excursions or if I need extended links, which I also cannot find for an 8" lift
I found front sway bar end links for 8" lift but the rear is really frustrating me
View 11 Replies
What sensors are in the front bumper? I slid out on black ice into a snow bank and it crushed in the bottom grille and as I'm clearing out the snow I noticed a sensor dangling with a broken harness that I was wondering what it was for. I have a nonFsport bumper with LED fog lights and both fog lights are operational.
Drivers side close to the fog lights
View 5 Replies
I just noticed today that my backup camera now shows part of the rear bumper and perhaps some of the chrome. There's also a strange, small, somewhat circular thing in the upper right corner of the screen. With my Matador Red exterior, I'm sure I would have noticed it before today on the backup camera.
View 8 Replies
How to remove the rear bumper, I have to drill some holes to install some back up sensors. I rather not but I don't know if anything is behind there.
View 1 Replies
So I've seen a lot of people on here wrapping the mid section of the front bumper black to give it a more aggressive look.
For those that have done this, will I need to cut a hole for the sensors or will the sensors still work with the wrap covering them?
View 9 Replies
My back up alarm hasn't been working all the time. I checked for the clicking sound when it wasn't working & could hear the clicking. The light is on all the time when its acting up. Is there a control box somewhere?
View 9 Replies
I'm having an issue with my backup sensors when its cold (40 and below). The issue is, they don't work. When I put it in reverse the sensor light on the dash comes on signifying they're off. I push the button to try to turn them back on and it stays on with no change. Once the outside temp heats up they start operating as normal. How to fix this?
View 10 Replies
The backup alarm sounds when I put the truck in reverse when there is nothing behind me. I found posts about people not getting any sound at all but none like mine. I'm guessing I have at least bad sensor that 'thinks' there's something in the way when there isn't.
View 5 Replies