Ford Excursion :: A/C Gauge Reading - Leak In Low And High Pressure Valve?
May 20, 2017
These are my gauge readings at 70 degrees Fahrenheit. According to an AC conversion for gauges calibrated in Pascals, 35-40F converts to 241-276 KPa, 140-160F converts to 1000-1103Kpa. The gauges are in Mpa which by conversion is 3 decimal points to the left so .241-.276 and 1-1.103 Mpa. Here are my gauge readings at 68 degrees ambient temp. Rear air is same as an ambient temp on max ac and the front is pictured. There seem to be virtually no pressure differences which I would interpret as a novice that there is ) freon flow.
There is freon in the system with the high pressure being approx correct but the low side is too high if I understand correctly. Basically when at highway speeds at 75 degrees yesterday the front AC was cold and the rear was outside vent temp only. There are slight leaks in the low and high-pressure valves. I have a Mastercool replacement tool but they did not send a fitting for the high-pressure valve. What these readings mean as far as what may be wrong?
View 14 Replies
Advertisement
I have been having an intermittent (2 times in the past 2000 miles) oil pressure gauge not reading. As I own a 6.0L I understand that this is just a pressure switch in reality and if the engine was starved of oil the HPOP system would kill the engine. The first time the oil gauge went out it was raining out. The second time was after going through a carwash and getting the underbody wash. At this time my battery light also came on for a few seconds.
Both problems seemed to go away after an engine restart. Today it is snowing lightly and my battery light came on again. I happened to be monitoring the battery voltage and FICM voltage via OBD II using Torque app. At no time while the battery light was on today did the battery voltage drop below 13.5V. The FICM was also stable at 48.5+/-.5V.
As the battery voltage read by the PCM is not actually dropping and the previous oil pressure gauge and the fact that my left blinker indicator is out I am thinking I may have electrical issues with the gauge cluster. I have never had these issues while driving in dry weather. Where do I start troubleshooting this? Also I am going out of town for the next two weeks and my girlfriend was going to use the vehicle. Is it OK for her to drive?
View 1 Replies
I have a 2002 Ranger V6 3000 with 100K miles. Can I add a higher viscosity oil since my pressure gauge is acting up. I changed the sending switch twice but the gauge still acts up occasionally. I was thinking of adding 10/ 30 on my next oil change. I do live in the area where the air temp is quite high in the summer. The truck runs well except for the oil gauge, in my opinion, is giving false readings.
View 14 Replies
I have a 2001 Ranger 4.0, 4x4 that just hit 100k and the oil pressure gauge doesn't show a reading for about 1 minute after startup. Also, the check gauge light comes on. What do I replace to fix this and is it something I can do myself? I am mildly handy. Would you worry about fixing it or just let it go because it's obviously getting oil pressure.
View 2 Replies
Just changed the fuel filter in my '04 6.0, no issues worked just like normal, filter primed truck started, great. Well now my fuel pressure gauge is reading dead 0, I know that can't be right because the truck is running, but noticed my fuel mileage seems about 2 mpg lower all of a sudden. Had R&R Injectors installed about 40k ago, figure it's just a bad gauge but wanted to check and see before messing with the frickin wiring. Also, have had a lot of pressure buildup in the coolant tank, has had head gaskets and studs, anything else it could be besides head gaskets? Have had a lot of wiring issues with this truck from the previous owner....
View 14 Replies
I have a 2001 Excursion Limited V10. 146000 miles 2 wheel drive. I have had it about a year and this is my first winter to really have experience with her.
When the outside temperature is very cold and the engine is cold from sitting all night, at start up, the oil pressure gauge reads nothing and the oil pressure/temp idiot light is on. Only does this during the first very cold start up or after sitting and engine getting very cold again.
I can drive just a short distance (2 blocks) and both gauge and light go to normal and stay there for the rest of my drive. I am using a quality 5/20 oil and filter and the level is good. Warmer days it has never happened. Truck runs fine, smooth idle, no "limp mode". She has not had any recent work done. All the other dash gauges read fine.
There is something about really cold temperatures that have to be causing the issue , I think. ??
View 5 Replies
Can I read oil pressure on my scan gauge II ? If so, how do I do it?
View 14 Replies
I was recently given my first Volvo. Its an 88 240dl. While driving my temp gauge climbs up to the red and sometimes hovers inside of it. It normally climbs up at stop signs and comes down on straight always then climbs right back up close to red. When the gauge was in the red i stopped the car and popped the hood open to see that the engine was not actually overly hot.
first i replaced coolant. nothing
then i replaced the thermostat. nothing
flushed radiator. nothing
Today i finally had enough and decided to switch out the water pump with a new one hoping that it would solve the problem seeing as it still had the factory one on. It did nothing. the gauge continues to climb up. I did replace one of the two senders in hope that it would fix the gauge reading but nothing.
View 4 Replies
I have a 2006 Jeep Liberty 3.7L that has a temperature gauge on the dash that reads an overheat when driving. The oil looks normal, there is no white smoke, no bubbling from reservoir. I have replaced the following:
Radiator
Thermostat
Water Pump
Coolant Temperature Sensor
Coolant Reservoir Tank
I am not leaking any coolant and the reservoir level has been fine. I have let the vehicle idle for 20+minutes, with no overheat. When I drive it around, the temperature gauge will read an overheat. When I stop the car and pop the hood, the engine is not overheated and both rubber hoses to/from radiator are flowing the coolant. The only thing that will bring the gauge down is turning on the heater full blast. Could this be the gauge itself being bad? Could it be a short in a wire somewhere? I had thought maybe a head gasket, but have no symptoms of a head gasket.
View 9 Replies
I have had issues for over a week now first problem check engine light not sure of the code but the mechanic said it was the spark plugs and vaccum leak hose (which I knew about the hose). $205.00 later replaced all 6 plugs and hose. Now today on way to work I'm getting that hesitation when in lower gear such as stopping and then accelerating it jerks some it was doing this alot before replacing the plugs.
We did a diagnostic code reader and it said the code P2402 I did read it could be my gas cap which I don't have a dealer gas cap on there now I did about 1 yr 1/2 ago but got a lock key gas cap instead. I have been doing some reading I would need to replace leak detection pump which apparently costly in repair.
BTW car has 119,000 miles I commute far from work 5 days a week. My car is very important part of my life! I did also read someone stated there was a recall on Mazda 6 wondering do I need to call the dealership to see if this is actual recall and I can cross my fingers get this fixed on them.
View 3 Replies
I have a 2009 Jeep Grand Cherokee. One of the tire valves has a slow leak. I figured I could get a new valve. But, instead, the guy reminds me that the valve has the pressure sensor built in. He could put in a regular stem, but then the light on the instrument panel would never go out and I'm assuming I couldn't get through inspection like that.
View 17 Replies
Truck has a high oil pressure leak, only leak i have found is in the high pressure rail, I cannot get to it till sat, or sunday. So I have to let the oil cool before I can start. Any way testing to find the right temp for Oil to thicken enough to Build? I've been here for hours and its went from 180's to about 100 now...
View 3 Replies
I have a High pressure oil leak somewhere, and where it can be. I tore the oil rails out and replaced the nipple cup seals last night. I got it all back together and air tested it and sure enough a leak is present. I have no problem paying for your time (I always provide good beer). I can rebuild gas motors all day long, but these diesels has me thrown for a loop. The frustration I am experiencing is crazy at this point. All the injectors are new, and the dummy plugs and standpipes were replaced as well.
View 11 Replies
Just had the tires rotated , then shop tech backs the X out of the shop, parks it and then hands me the keys. I hop in and turn the key , the truck turns over , but starts to shudder and buck, and fuel pressure gauge reads 0.
View 3 Replies
So a couple weeks back I'm on expressway home and I look down and and temp gauge is pegged out overheating I immediately pulled off and shut it down and towed to a buddy of mine's shop he flushed it filled it up w antifreeze and checked for leaks and couldn't find one. I drove it for about a week and got out to for a quick stop , Ex parked on a slight decline and came out to prolly half gallon of coolant on the ground..I limped it to my buddies shop as it was not running hot .. he has checked it out but can't find any leaks, even after having it run 30 or so minutes..
View 6 Replies
Just had dealer repair shop complete power steering fluid flush in Jan 2013. Vehicle now has lost all power steering fluid (April 2013) and dealer repair shop has told me it is due to high pressure hose failure - need to replace & then verify pump condition (dealer repair shop not sure if pump bad until hose replaced to test) for repair bill.. I was told this was not related to repair shop power steering flush because this hose not removed for flush or part of that procedure (at which time a transmission flush & spark plugs replaced (minor tune-up) . Just wondering if any pro mechanic can respond with advice about the relative close time frame these two events & if there may be a probable related reason?
View 4 Replies
After having my oil changed at a local place, the oil pressure gauge showed "high." hoping it would go away, i drove for a week. it didn't... took it back to the shop and they said it was a little full which would cause it to show high pressure. That was earlier today. The gauge however has not changed. Still shows high oil pressure. I need to drive 400 miles tomorrow and am not sure if it is safe? Perhaps just a bad sensor??? I need to know if i can hit the road or not.
View 5 Replies
I've got a 03 x with the 6.8 2wd 4r100. It was flaring pretty bad for a while going into lock up, about 2 months ago the flare went away now NO lockup. Its taking more pedal to get moving and alot more slip, once you reach cruising speed tranny goes into high pressure. Told to replace the selonoid pack, got one use from a tranny shop from a tranny that lost reverse, got it home took mine out and found out the new one is not PWM and mine is, I tested my selonoid by putting 12v to pin 1 and 4 and nothing (on the pwm pack) did it to the new pack and it works. My question is what will happen if I put the non pwm in my tranny that originally had pwm pack in it?
View 2 Replies
I have a 2003 Ford Excursion with the high pressure line leaking. My guess is that the original line had a rubber hose and was replaced with a 3/8" ID high pressure hose. My problem is that I can not get the 3/8" ID replacement hose over the second larger bulge on the line going to the radiator cooler. What am I doing wrong?
View 3 Replies
My 03' 6.0l hpop only makes about 1700 psi at wot, at hot idle the ipr is 25.1 and the icp is about 580. It runs pretty good but it seems the crank time to start is getting a little longer sometimes, other times it fires right up. It makes no difference if its hot or cold. Do pumps get weak or do you think I have a leak?....
View 1 Replies
I just replaced my injector cups a month or so ago and also injectors with some lower mile injectors. but now 3 weeks later still not getting any pressure at icp. I have dead headed pump got 3k plus but when i block off ether head i get no pressure. i have pulled injectors and checked for orings and they are fine...
View 2 Replies
