2005 4wd excursion. I have a leaking rear seal on passenger side.
I have the hub assembly off. I'm down to the spindle. My old seal came out in pieces. There's either a piece of the old seal or another seal on the back of the spindle.
Are there two seals? This what looks like a seal still on the spindle against the plate on the back...
While diagnosing an issue with my ebrakes I found the drivers rear axle seal was leaking coating the ebrakes in gear oil, replaced the seal. Decided to pull the differential fill plug and check to make sure it was full - drained a good bit out pulling the hub to replace the seal. To my horror this is what I find when I pull the plug. First photo is as it came out on the magnet - second is after a clean up. What is it? I am almost afraid to drop the cover....
View 14 RepliesPicture if you will...Removed tire, caliper and rotor. Removed hub, and knuckle containing the stub shaft/spindle with it's yoke for the U joint. You are now looking at the end of the axle tube, with the axle shaft in it, one end connected to the differential carrier, the other end has the yoke for the U joint on it. Just inboard of the yoke, is a seal. Apparently it's called a "dust seal" is there a bearing behind this, or is the first bearing all the way in at the differential? When I was doing my brakes, I noticed the passenger side u-joint is shot, and the axle wiggles around in the dust seal. Figured I'd replace the seal while I was doing the U joint. Also, how do I get the axle shaft out? Just pull, or do I have to remove a C clip from the inboard end? What is the right National part number for the seal? I have a 6/2000 Excursion.
View 2 RepliesIts been awhile since I have been on. Everything has been running great for me until I found my passenger side front axle leaking fluid. I'm sure something has been posted on here but I have limited access to internet right now and need to know what I am getting into to change the seals. From what I have found there is an inner seal in the pumpkin and then an outer seal and dust cover. Are both of these easy to change? Are there any special tools needed? Do I need to remove the gears in the pumpkin? If so, is this difficult and any special tools required for this?
Mine is a 2001 V10-6.8, 4x4 no mods at this point.
So this morning is just getting better and better. Was coming back in from getting the mail and noticed a small puddle under the passenger side tire/wheel area.
I never ever have a puddle of any sort in my drive way so...I start crawling around the truck and this is what I find. I can free spin the dust seal, but its all the fluid that has be worried. With less then 4 days till I have to haul everyone to the airport this is not what I need.
IF (man I feel stupid for asking) IF I leave it in 2 wheel drive how big of an issue would it be to drive it?
None of the parts will be in before I have to drive everyone out to the airport, this is the only reason I'm even considering this..
Plus would this explain a sudden lost of MPG?
Here's my problem while replacing brake pads i found that my axle has leaked fluid on the pss,side rear rotor and all over .. I been looking for any info on repairing it myself . I found Everything for every other truck just not for this truck.
It's 2003 F-250 w/5.4L all Stock rear axle has 12 bolts and gears are 7.73 ... I believe its a Dana 60. No tags or markings on the Axle to go by..
I live in the Freak-en woods here so i like to order all the right parts once and do over the weekend .. its my only ride so once apart im stuck here.... I did check the Vent Tube its fine..
Passenger differential axle seal is leaking again. It was replaced twice already. My mechanic checked the seal...its not damaged. Its not a excessive leak. Both times, the seal were replaced with OEM. I don't want to buy another one and replace it.
Its a 1995 Celica, 5SFE, 5-speed MT. 98k miles.
I have noticed a few drips coming from the rear axle input shaft where the drive shaft connects. It has only done it once and there is no residue on the trailer hitch so I know it didn't dump everything on the road. If change this seal, how difficult is it and do you have any information which might make it easier.
View 14 RepliesSo I have a 2004 Hyundai Elantra 5 speed. The driver side cv axle seal started leaking a few months ago and I finally got around to repairing it. Everything went relatively smooth until I got to replacing the seal...
The problem is, it will NOT fit over the cv axle. It just won't. When the seal is installed, not matter how much force I put on the axle it will not go in. Also, I even pulled the seal back out and tried to put it onto the axle out of the car and there is no way it is going on. This is the third seal (done the rounds to through the big name parts stores) and no go.
Now, some quick car back story, I generally do all of my own repairs, but over the winter in the midst of a family tragedy I had a friend (professional mechanic with a shop) do a bunch of work to the car. He replaced the boot and joint that goes into the transmission (he did not replace the entire cv axle assembly for some reason). What I am beginning to think is that he replaced it with the wrong part.
Now, what I am wondering, is this even possible? Is it possible that it could fit and work perfectly yet be wrong? This also appears to be what broke the original seal. The inner portion of the seal was totally blown out in a circle, but perfectly, like it was crushed or cut out, and I am wondering if this happened due to having extreme force applied to it (possibly when he reinstalled it?)
That, or is it just extremely difficult / next to impossible to get these seals on? Even with both parts out of the car, stretching and pushing down on the seal (oiled it up as well to see if that would work) with all my might yields no results.
The leak was not there for the first month or so that I got the car back and then showed up. I have put about 5k miles on the car since I got it back. With Monday quickly approaching, I am wondering if I should just blow the crap out of my budget and pick up a new cv axle? I could at least have them pull one and let me see if the seal fits, I suppose.
My wife has been complaining about a noise from her 2005 expo.
As she drove the truck today I have narrowed the noise down to the right side of the half shaft. From looking underneath and comparing what I was seeing and hearing, the track bar is not centered. Its more in on the driver side and out on the passenger side. I had her to stand on the running board and shake the truck.
I can definitely hear a kinda cluck? It sounds like the half shaft going to the tire but at the same time the bushing on the outer tire rod end. I can't determine what it is exactly.
when you rock the truck you can definitely hear it. Its not like violent loud but i'd like to get it taken care of. I looked for some grease points but I don't see none..
2nd question for the grease points that I do see how much do I grease it? how many strokes?
I have a 2006 sonata 3.3 with auto trans I'm having trouble with fluid leaking from the passenger side axle seal. I have already replaced the seal with a Hyundai seal and it is still leaking. Not as bad as before but it leaks onto the exhaust and smells really bad. The transmission is not overfull...
View 2 RepliesOn my 2003 Excursion 7.3L, I notticed I'm leaking what I think is coolant from the passenger side rear hard line by the front spring hanger. I haven't pealed the plastic loom away yet, but I did see the loom is chaffed near the spring hanger. What lines are the ones that carry coolant, and can I just cut the hard lines and replace with a section of rubber hose?
View 3 RepliesI have a 2005 F350 XL Heavy Duty 6.0L truck that has 68,XXX miles. I recently changed the rear brake pads and about a week later the rear passenger side is leaking brake fluid. The fluid is slowly dripping from the bottom caliper bolt but i am not sure if there are seals in this area. the driver side is fine and the fluid is only leaking from the bottom caliper bolt not the top.
View 2 RepliesMy wifes car started leaking gear lube in the driveway. I traced the leak to the passenger side output flange seal. At first I thought the cause was a bad CV joint but when I tried to shake the axle, I noticed the whole flange moving...How can this be repaired? Does the whole tranny need to be removed or just the output pod?
View 4 RepliesI noticed the other day after my truck was parked on a bit of a angle there was diff oil from the passenger side on the ground. reading a bit on here i learned the axle seals are way in the front housing close to the front diff. and yesterday driving a heavy load around my front brake driver side got stuck on a bit and over heated and was smoking, couldn't even touch the rim it was so hot. anyway about this axle seal i got the hub off right now but cant seem to pull out the axle assembly through the knuckle but i see i have to pry and most likely wreck that seal. Looking for a link of piuctures or how to replace the axle seals in the housing.
View 11 RepliesI took the front axle shafts out a couple months back and remember NOT seeing any differential fluid in the axle shaft housing. But then when I took the tire off tonight.. I noticed diff fluid leaking from from the axle shaft dust seal ?
1. I didn't think diff fluid flowed up near those front dust seals ?
2. That's a brand new dust seal so I'm guessing some debri must be in the connection causing the leak ?
I unstuck my front axles yesterday and while under the car spinning the front axles freely and enjoying my easy fix, I noticed a rubber seal (a thick squared edge round rubber seal) sitting loose and spinning freely. Its next to the axle joint, right before it disappears into the housing.
I'm guessing this is a dust seal of some kind. There is no fluid leaking out...
I'm wondering if I can just press fit this thing back into place or do I have to take the whole front wheel assembly (hub, bearing, axle, etc) to get the seal back into place.
I'm wondering if it broke off from a larger seal or if this is the whole thing? You can see how the seal isn't sitting quite straight. It actually just spins around.
99, F250, 4X4, V10, 72,000 miles. I have had the front axle seals replaced three times in the past 3000 miles, and the right continues to leak. My mechanic screwed up three times?
View 6 RepliesWhen I took my Saturn L300 to the dealer recently for its regular oil change I was told that my right front axel seal was leaking and it will cost me $580 to replace. This seems awfully high to me. Am I getting fleeced by the GM dealer?
View 1 RepliesI recently had my rear axle seals replaced due to leaking. Does the rear diff fluid get replaced on that repair since the rear diff cover comes off? Trying to figure out when my next interval for changing rear diff fluid should be.
View 1 RepliesI have an 04 Limited, 6.0 PSD, 4x4 which I need to replace the front inner axle seals, the right side is leaking out the shaft. I have watched a couple of YouTube videos on how it is done but would like to get some first hand knowledge and recommendations.
First, how important is it to check the backlash before beginning the removal of the gear assembly? Do I need to remove the pinion gear as well or just the gear assembly?
How difficult is it to get everything back on place once the seals are replaced? I have not done this type of repair before and am concerned I might miss something.
I am planning to replace all the ball joints at this time also, this was the primary reason for this maintenance in the first place.