Ford Excursion :: 2003 - RAS Installation?
Dec 2, 2012
Trying to get myself up for the install of my RAS!
Have to finish watching the first set of games tho. (NFL Sunday Ticket)
Dec 2, 2012
Advertisement
Ford Excursion :: Installation Of Horn?
Or to put it another way - Yet another Hadley air horn installation. First up made a mounting bracket for the horns......to mount them on the frame.Then another bracket to mount the air tank, wiring and compressor. Finally fitted an illuminated switch to change from OEM horns to the Hadleys. This switch illuminates dimly with the parking lights and brighter when switched to the Hadleys.
View 12 RepliesFord Excursion :: Warn Hub Installation?
I'm running out of light and I need to find the Warn Hub installation thread.
View 5 RepliesFord Excursion :: Remote Start Installation?
With snow on the ground all winter here (usually), and the summers getting into the 90's I was thinking about getting a remote start system. I know Viper is the big name but I just want something to start it, not do a bunch of prima donna functions I don't need. I normally do everything myself but electrical is not my forte and I hear that a DIY person can't get much info because they think only installers should do it. Also from what I gather, it takes a relay due to the transponder key. I am thinking $200 max and I hear Best Buy can do it all.
View 14 RepliesFord Excursion :: Brake Controller Installation?
Well I have my new 8.5x20 trailer on order that has electric brakes and I'm looking to install a brake controller. I don't like how cheesy all the aftermarket ones look and love fords factory controller and upfitter switches. Looking for info on swapping these in the excursions and had it working? I've looked on the net for this mod and came up with nothing.
View 14 RepliesFord Excursion :: F650 - Dash Kit Installation?
I am i the process of installing a F-650 dash kit. I am going to relocate my DP tuner to a location next to the power source to the right of the heat/ac control section. I am going to cut out a section for the mounting bracket. My questions are:
1: What's directly behind that section?
2: If there is something directly behind it, can I remove just the front section of the dash or do I have to remove the entire dash from the windshield?
I am going to have to remove something anyways for the lower kit to be installed.
Ford Excursion :: 2002 - Rear Heat Installation?
I picked up an 02 ex value xlt with out the rear heat i was wondering if any of you have installed it in a truck that never had it. i work at a scrap yard as a mechanic and will hopefully have a truck come in with the parts i need, what it all entails. Any headliner out for some odd reason maybe you could snap a photo of the piping.
View 14 RepliesFord Excursion :: 2004 - Dually Rear Installation?
I am considering converting my Ex to a dually. I have located a 2006 dually rearend with the same gears as my rear. My Ex is a 2004 4X4 so I am interested in how easy the physical installation would be to put the 2006 rear in a 2004 Ex.
View 14 RepliesFord Excursion :: 2001 - Installation Of Automatic Headlights?
I recently bought an 01 Excursion Limited 4wd 7.3L diesel. I have several projects I want to do so this. I would like to add the auto headlights Ive seen on other trucks.
View 14 RepliesFord Excursion :: Installation Of Center Jump Seat?
I just ordered a ford center jump seat and was looking for some type of instructions for removing the arm rests on the captions chairs. I have herd of others just cutting them off, but was looking for a way to salvage them in case I cant live without all my cup holders.
View 6 RepliesFord Excursion :: Rear Brake Caliper Line Installation?
Routine maintenance gone wrong.
Installing rear brake line and failed to put on the rear washer and stripped out the bolt hole mostly. Will still unscrew and screw back in but not enough to stop a slow drip. Is there an easy repair or time for a new caliper? Thread tape is not brake fluid resistent.
If no repair, what brand should I go with? Are they all similar or MC better? Can get Fenco for $50 and MC for $100. A1 Cardone and ACD for about $75.
Ford Excursion :: Location Of Reverse Wire For Backup Camera Installation?
My reverse camera goes over the mirror, its a mirror when not in use and a camera when in reverse. The way this one is set up, the camera taps switched 12 volts at the rear of the car (tapped trailer connector for these) and the video signal runs forward (ran under headliner to center console to mirror). The monitor needs 12 volts, ground, and + 12 volts when I shift into reverse. I just read a half dozen threads where people suggested tapping into a black wire with pink stripe in the driver's kick panel. Just checked, no such wire on mine. I do not want to run a wire back from the taillight, this seems backwards since the power goes from the front of the truck to the reverse light in the taillight I just need to find the right wire. I checked the reverse relay and the fuse in the fusebox and they are both 12 volts when the truck is on, so they must be prior to the reverse switch.
View 14 RepliesFord Excursion :: 2002 - Installation Of Larger-screen Flip Down DVD System?
I just bought a 2002 Excursion limited. It has a tiny flip-down screen in the roof and a VHS player in the back of the center console. I would like to install a larger-screen flip down DVD system, but do not want to chop things up. In other words, what options are out there for a stock-appearing setup with larger screen?
View 6 RepliesFord F-150 - 1997-2003 :: 2000 - Tachometer Installation To The Dash
I have a 2000 F150 2WD 4.6L and been thinking of installing a tachometer to my dash. I did it to an '88 Ranger easy, It had A coil, distributor and regular spark plug wires. How would I go about this project I would like to undertake?
View 2 RepliesFord F-150 - 1997-2003 :: Power Door Lock Installation?
F150 - 2003 ... Do some of these trucks actually not have power door locks that operate both sides? Or, is there something wrong with my newly purchased truck's door locks? If so, how hard is it to put in an aftermarket electric door lock?
All I need is for both the things to lock from one door. I haven't had to manually lock all doors in a vehicle I have owned for over 30 years, and it is hard to teach an old dog new tricks.
Ford F-150 - 1997-2003 :: 1998 - Installation Material For Bug Shield?
I bought a used bugshield for my 98. I know how to install it but it didnt come with installation materials. What screws, washers and so on do i need?
View 3 RepliesFord 7.3L Power Stroke (1999-2003) :: Engine Won't Working After Re Installation?
So I posted a while back about fixing all the leaks I had and what I was going to do. I finally completed all the repairs and reinstalled the engine and it won't start. Cranked a bunch and checked oil level in hpop its good so I pulled plugs in oil rails there is oil present there, cracked the yellow valve on fuel bowel there is fuel there. unplugged the icp sensor and cranked more still no indication of wanting to start.
View 14 RepliesFord F-150 - 1997-2003 :: 1999 V6 - Inline Trans Filter Installation
I'm doing a trans service soon on a 99 F-150 (4.2 v-6 with a 4r70w) and want to add a Wix inline filter. Is the rubber section on the cooler return line 3/8"? I'm also thinking of swapping the stock trans cooler with one from a 2003 7.3 superduty.
View 2 RepliesFord 7.3L Power Stroke (1999-2003) :: Installation Of Remote Start System?
I've been looking for a remote start system to install on my truck it has no remotes of any kind now. I've been googling most of the day and i can't seem to find anything except something that hooks to a edge tuner of some kind.
View 6 RepliesFord 7.3L Power Stroke (1999-2003) :: Installation Of Fuel Pressure Gauge?
I bought an Autometer 4763 gauge that didn't come with the correct fittings to plumb the sender into one of the extra ports on the back of the bowl. I went to the Ace hardware store right across the street and they didn't have anything (not surprised) and then Napa. They couldn't find a fitting to match either. He found that the plug threads are 7/16 20 tpi and the sender is 1/8" NPT. He suggested getting a 7/16 20tpi bolt, drilling it rifle-style, and then tapping it for a 1/8" NPT. The alternative, and what I ended up doing, was to use brass fittings to tee it off one of the supply lines to the heads. I ended up going that route but wanted to know if I should have looked harder for the right fitting.
Here's a pic of what I have now. I've test fit it, and it seems to work although I will need to insulate the hard lines because they rub due to the offset.
Ford 7.3L Power Stroke (1999-2003) :: Fuel Pressure Gauge Installation
Looking for pics of where/how they mounted their fuel pressure gauge? I'm getting ready to install one.
View 11 Replies