2003 X limited 2wd 6.0L ... My cruise control was working intermittently. Could it be the buttons on the steering wheel itself? there is a cluster that I see. Does it pop off to expose the connectors/switches? Can these go bad? Can I buy new switches for the steering wheel?
View 2 RepliesI had had intermittent issues with the cruise control not working in my excursion. most of the time it was fine though. after a recent 150 mile trip it stopped working half way through. i didnt worry about it too much..got back into town and checked under the hood. i found brake fluid running down the inner fender well! all over everything under the master cylinder. finally tracked it down to the cruise control switch on the master cylinder leaking. I pulled the plug apart and it was full of brake fluid.
Meanwhile the master cylinder was about half full, so i replaced it with the same switch out of a '96 parts explorer which is the same part luckily. also yes i have had the cruise control recall done. So if you have lost CC and you have a leak replace the switch! seems it can leak..and at a pretty good rate..alittle scary! glad i figured it out before my 800+ mile trip later this week/weekend.
I have a issue with my cruise control not working. The Ford dealer in my home town has had my truck for 3 days now and cannot figure out what the problem is. I finally went by the dealer and wanted to know what the deal is and how can this take so long to figure out when they have to of seen issue like this in the past. The tech that is working on my truck said he has traced wires,etc and think it has something to do with the after market JVC touch screen DVD/backup camera. My question is would this affect the cruise? I cannot find anything on the net that may point in that direction. The steering wheel controls work for the fan and temp controls but not the radio as its aftermarket. Radio adapter for the controls?
View 14 Replies2002 Ford Excursion cruise control inoperable. Problem began when cruise would come on intermittently. I would push the on button then set, at which point the green cruise icon light would either come on and the cruise would set or she would flash and not set. Sometimes holding the switch down worked, other times not. Now no matter what I do the cruise will not engage.
I have had the recall done for the cruise control by the dealership.
I have checked the fuse on the recall module, the 2.5 is in good shape and not blown.
I also found this guide to a self test (copied below). I used the test, turning the key on with the off button depressed yields a green speed icon light. Letting go and pressing on yields a green flash as well. But when I move on to pressing resume I get no lights at all, same if I continue through the other switches, no more lights.
Here is the self test guide -
*cruise control self test
Enter self-test diagnostics by depressing the speed control OFF switch while turning the ignition key ON, making sure the engine does not start and is not running. The speed control indicator on the instrument panel will flash once to indicate that speed control module entered the diagnostic mode. Five additional flashes at this point indicate a defective speed control servo.
Release the OFF switch.
Press the remaining switches in this sequence: ON, RESUME, COAST and SET/ACCEL. If the ON switch is not depressed within five seconds after entering the diagnostics mode, the module times out and the procedure must be started over.
The speed control indicator lamp will flash as each switch is depressed. Press each switch in the sequence immediately after the indicator light goes out for the previous switch. NOTE: There will be a slight delay when the last button is pressed and the lamp flashes.
A lamp flash with the last button (SET/ACCEL) indicates that the static test passed. If the lamp does not flash with the last button and there are no additional flashes of the lamp, the switch is defective. If the lamp does not flash with the last button, and additional flashes occur, follow the chart below for trouble codes:
2 flashes - BPP defective, circuit is defective, brake applied, CPP switch or jumper (if equipped).
3 flashes - deactivator switch is open or circuit defective.
4 flashes - vehicle speed signal is out of range or circuit is defective.
Immediately (.25 second delay) after the static test, the speed control servo does a dynamic test by automatically actuating the throttle lever from 8 mm (0.315 in) to 12 mm (0.472 in) of travel from the idle position. During the dynamic throttle pull, observe throttle movement to witness any binding or sticking of the speed control cable and correct connection of speed control cable to throttle lever. Make sure the throttle returns to the idle position.
Have this problem?
View 2 Replies1999 F250.. What would cause my cruise control to work sometimes and not others. it may work today and not tomorrow.
View 2 RepliesLooking for any pointers on fixing my cruise control Have looked around under hood but what it looks like. I've got the air working again,put Warn hubs on and have ordered the Hellwig rear sway bar,adjusted steering box i/2 turn....
View 14 RepliesThe cruise control in my recently purchased '01 Excursion isn't working. I've done a lot of searches and discovered there was a recall for a wiring harness: 2001 FORD EXCURSION Recalls
I called my local dealer and they stated there aren't any open recalls for this vehicle, so the previous owner must have taken care of it.
Is there any way I can verify that the warranty work was done? Can I visually inspect the harness? What else I can check to fix the cruise control? The lights on the steering wheel are illuminated.
I have a cruise control issue. I tried the self diagnostics test, and the "cruise" light would not come on. (Also read that 2001 did not have a self test, so maybe that's why it didn't work? Also, when I first start it, all the other lights turn on except for cruise.) I checked the brake master cylinder and it has the double fuse wiring with 2 good fuses. Not quite sure what else to test. I just bought the X knowing it had this problem, but didn't know how much I would miss cruise control until driving without for a week.
View 12 RepliesThe cruise control on my '05 Avalon Limited was working intermittently for a while. I'd hit the button to turn it on and nothing. Then a few miles down the road, I'd hit it again and it would work just fine. Today I tried to turn it on and nothing. Three different trips today and no luck.
View 1 RepliesMy fuel gauge is not working, nor is the cruise control, Had the truck looked at, was told the cruise was not working due to the fuel gauge not working?
Also when he hooked it up was told the dash gauge worked fine and the computer showed 60% which would have been about right based on mileage on the tank. My guess is that I need a sending unit?
I have a question on my '00 7.3. Cruise control just quit working. From reading the threads/forums I have gotten some ideas, but how about no dash light when turning the key to on? Nothing with the self test also. How can I troubleshoot the switch in the steering wheel? I could also have a bulb out in the cluster, but either way- no cruise function.
View 4 RepliesOne day it work and the next day it didn't. I checked the 15a fuse and it was good. What else should I be looking at?
View 12 RepliesThe ruck is a 2002 Ex limited v10 4x4. The cruise worked fine till my wife drove the truck! the green cruise light blinked a few times, now, there is nothing.I'm no good at electrical issues.
View 3 RepliesMany of you said it was the "ClockSpring" that needed to be replaced. But I already did that. A brand new clockspring on it. The horn only blows when the engine is off and when the engine is on the horn and Curse Control don't work. I have a 2001 Excursion. So What could the problem be? It works with the keyless remote. But just when you driving down the street and some bone head cut you off you can't just it.
View 5 RepliesI have a 2005 Excursion 6.0 ... .. A few months back the horn started sounding on its' own in the night, so I pulled the fuse... .. Then the Cruise Control stopped working. I have googled references to clockspring failure and these problems... ..
View 3 RepliesMy speedometer stopped working yesterday after i replaced the 2 cruise control buttons on the steering wheel. When i connected the the battery the horn started blasting and I went over tap the horn then it stopped. Then i noticed that the horn did not work anymore. I put back the original cruise control buttons and still did not work .So know instead of fixing the cruise control buttons, I broke the horn and the speedometer while the cruise control is still broken. I checked the fuses and they all are good. What can it be ?
View 6 RepliesI have a1994 Dodge 1500 Ram Hemi extra cab 4door. The brake lights on the bed of the truck not the high light will blink on and off and sometimes stay on the other day my son-in-law narrowed the truck and a trailer and the trailer also blinked but again not the high light. Also the cruise has stopped working about the same time this started. At one time it was infrequent now is most of the time. Wondering if it could be part of the alarm system or something else it is driving me crazy.
View 4 RepliesA few years ago I had the clutch changed on my 1997 F150. Afterwards the cruise control wasn't working. When I brought the truck back to the repair shop I heard the manager tell the mechanic to "attach the clip by the pedal" and that fixed it.
I just had some work done, had to replace the oil pan, and the mechanic had to remove the transmission. Now the cruise control doesn't work. I changed the Pressure switch but it didn't fix the cruise control. What that clip might be that fixed the cruise control last time?
I have an '02 F150 Lariat CC 5.4L. The truck is new to me and neither the cruise control nor the horn works. i have checked all (known) fuses and relays. I have tried the cc diagnostic, and the dash light DOES NOT illuminate. Should I assume that the dash light is not burned out? Is there a way to test the clock spring connections for continuity? and how do I access the connection
i checked the cc brake pressure switch and have continuity there.
I did the diagnosis,on my non working cruise control on my 2000 f250. The cruise light came on when, I, depressed the off switch and turned key on. I depressed on switch,cruise light came on.
I then depressed the resume, coast, and set switch, as described in the diagnostic procedure,suggested,and no light came on. Do the switches for the cruise control are bad.
I have checked the fuses at the power distribution box under the hood and checked the fuses under dash,all are fine. I just replaced the switch at master cylinder, as it was leaking and it had the recall switch replacement, too.