Ford Excursion :: 2002 - Sloppy Shifter Lever
May 23, 2015
I've been experiencing the ever so popular sloppy shifter lever in my 02 excursion. So naturally I started prowling around the site looking for answers to my issues. I have ensured both of the torx bolts are present and tight at the end of the shift tube on the bracket that connects to the shifter cable and have replaced the shift tube (It was worn out) and it worked great but has not completely fixed the issue so today I crawled underneath the truck to try and adjust the shift cable and have found that the detent in the shift linkage from the gear position sensor that runs to the shift mechanism (not sure what it's called) that is inside the transmission is really nonexistent, it is effortless to move it from P to R but from R to N is good and stiff like it should be but from N to D and D to 2 is effortless. I have zero experience with what creates the detent inside of the transmission and looking for a link or pictures or write up something that I can look over and attempt to educate myself on before I dive in to this blind....
View 14 Replies
Advertisement
I have a 96 ranger 4.0L shift lever was very sloppy and one of the torq bolt fell on the floor I used loc tite and tightened them up with no problem put everything back together and now it wont start. I think I checked everything even replaced the neutral safety switch, adjusted the tranny cable, checked fuses and switched around the relays maybe an ignition switch? I am running out of stuff to troubleshoot.
View 13 Replies
My mom's 95 shifter is slowly getting worse. Right now it's at the point where we have to hunt for gears just to put it into park or reverse or d/od. It's not stiff like the rest of ours, hers is all sloppy and loose. She says it's been doing this for a while, but i think it got worse when i pulled her cluster out to change the light bulbs. I say this because i couldn't get the needle cable un done, so i just let the cluster rest on it while i was changing the bulbs, which put a little bit of tension on it.
View 14 Replies
Having trouble with shifter not going into park. The linkage is sloppy. Is there a bushing kit or something to tighten up the linkage?
View 3 Replies
The Speed Needle works fine. But...the Odometer part quit some time ago. I can't tell what my fuel Mileage is now. How to troubleshoot this problem?
Things that might affect this problem; Transmission skids loudly when going in and out of 4-OD. It could be the Torque converter clutch?
The Gear shift lever is sloppy. Doesn't fill me with Confidence.
Brake fluid warning light is on most of the time. Fluid level is up hi though. Driver door mirror control switch don't work in one direction Who on this Forum has a Switch for me?
View 14 Replies
98 f150 4x4 5.4... So i purchased this truck about 3 months ago and now I am having problems putting it in Park. The column shifter is very loose and sloppy. Is there any way to rebuild this?
View 3 Replies
I have an '86 Aerostar with the 2.3 four and 5-speed stick. The shifter is sloppy, and it's often hard to find 4th when downshifting from 5th, and sometimes, it shifts hard through all the gears. Other times, it works fine. The manual says that this shifter was used from 86 to 89 only. Did they use the same one on Rangers? Can I buy a rebuild kit? Or, is this a sign of some other problem such as the clutch slave cylinder?
View 1 Replies
I have my GTi, a week ago I broke an axle. I was then convinced by friends the clutch went out. So I said screw it and bought a Southbend Stage 2 Daily. When I get it I go to install it, then find out I have a Broken half shaft. So after taking the tranny out to install the clutch anyways and everything goes alright for the most part. (250k miles so that's why I never returned new clutch)
SO I get everything together. Tires spins. Car goes all is good.
Clutch is super spongy as I need to bleed it. But my problem is the shifter knob is super sloppy. Feels like is a whole section lower. It's hard to engage second as I have to double tap it in with a good throw. Everything is right on the shift tower. And seems like it clicks right into all the gears. But the physical knob feels super sloppy and out of place. First, third and 5th are all super far up and seems like it double clicks after putting it into gear. Like if there was a gear above. Kinda weird to explain. I've done the home alignment on the tower and nob, but only have a bolt that was 4.71 mm. So the cables should be really close to being aligned right. But I can't grab second at high Rpms.
I also need to do my drain and fill. So would it be a drain and fill and clutch bleeding will fix my sloppy shifter? Before I did everything it was tight. Felt right.
View 2 Replies
1999 F-350 . My shifter lever is extremely loose, it will not go into park at all. I tightened the two torx bolts, adjusted the needle but its still bad. Im thinking the cable is loose, I saw that there is a small rod attached to the end. Is there a way to tighten it or do I need a new cable assy.?
View 5 Replies
My 2009 Ford Escape shift lever is stuck, not allowing me to shift out of park without using the manual override. However, when I slam my foot to the brake (rather than simply stepping on the brake), the brake switch relay, etc. all engage and I am able to shift out of park. Is this a brake switch relay problem, or is it possible that it has to do with the age of my brakes, etc?
View 3 Replies
2002 toyota echo ... I can't get the button on the shifter lever to go in. It isn't the overdrive button. The cable was replaced last fall but this seems to be a new problem ...
View 1 Replies
I am the original owner of a 2001 Ford Excursion with about 262K miles on it. I have thought about selling it more than once but I have finally come to realize that this is a very sturdy and reliable truck - so why sell it?
With that said, there are a few items that I need to address. The most important right now for me is to get the steering adjusted some how to eliminate the looseness. It is especially noticeable when driving on the interstate, I guess because I am traveling faster.
I am not a skilled mechanic but I do want to learn more about performing some of the simpler maintenance items since I have lost faith in the auto repair shops.
View 10 Replies
My Gen iii four has a small light that shines down from ceiling and illuminates the shifter area. Can this light be turned off while driving?
View 19 Replies
I have an 01 Ex, 6"lift, 35" tires, 185,000 miles. I have gradually gotten to this point where the steering is very loose. I can roll the steering wheel back and forth with out "catching" the wheels & with the bigger tires, they catch grooves in the road & pull the vehicle side to side. I took in to a reputable 4x4 shop & he suggested the steering gear box was going bad. So I had them replace that. That did solve about 50% of the problem. So what is the next thing to look at??? Ball joints?
View 12 Replies
As it turns out, my shift cable wasn't bad. The transmission lever coming out of the transmission doesn't want to move very easily. When in gear, it shifts fine as it should, so I'm thinking something is bad with the lever. Problem is, I don't know what could possibly be causing it.
View 8 Replies
I recently bought my first EX and I finally had enough of looking at this
The transmission shift lever indicator not being in the proper position needed to be fixed!
After some searching, I realized what the issue was and was quite surprised that the "fix" is replacing the entire shift lever indicator assembly. Seems overkill but right on par of with the way the world works nowadays.
The other solution I found was by a company called Dorman. They make a Shift Indicator Cable Bracket, which is the only part that was damaged in my case as you can see here. The white part pointed at by the arrow is supposed to be attached to the rest of the white plastic.
I looked around the garage thinking I need some glue. And something to reinforce the freshly glued parts. That should have been much more difficult as I don't regularly fix tiny plastic parts BUT I quickly came across this old external hard drive cover.
Broke some tabs off, trimmed them to size and poured glue all over the place.
This is what I ended up with.
Now my OCD can focus on something else
View 2 Replies
I have a 2002 Camry 4 cyl LE with a 4spd automatic transmission. Recently I have been experiencing slow long shifts from 1-2 and 2-3. It's as if it is coasting in neutral for a couple of seconds before finally engaging the next gear. I experience this sensation only after the vehicle has cooled down. The transmission will start to shift like normal within 3 miles of driving. I have only experienced this recently as the weather has started to drop.
I have not changed my transmission fluid much as it is a synthetic and Toyota claims it will last the life of the car. I did a drain and fill at 90K mi. The car currently has 150K mi on it and after experiencing these problems I did a drain and fill, drove the car 10 miles and repeated with another drain and fill. This seemed to have worked on the first day after doing this but now it is back to the slow long shifts. I am thinking of cleaning the strainer and taking the car in to have the transmission flushed. Is there a way to tell if my transmission is failing?
View 8 Replies
Last year, July, replaced Trans.modulator..All went well. Now..sloppy shifting, occasion heavy thump changing gears when slowing. Trans. people say All good according to their programs.....but they also feel the same problems. Its an internal problem, they say, too expensive to tear down.Drive it until it dies. ( 161 K on the odometer.....otherwise is perfect. I want to do a flush, then drop the pan, change the screens, tighten the bands and replace Trans. fluid.
View 1 Replies
Overdrive off button hasn't worked in a couple years and there is no power to the switch so I figure the wires across the column are damaged. Even after replacing the button a couple times the ends were always falling off so I'm ready to replace the entire shifter arm assembly. I also need to replace the bushings since the arm is loose.
I will also be installing yet another turn signal since the one from Rock Auto didn't last long. The new one will be from Auto Zone, which said the shifter arm is a dealer only item.
View 5 Replies
4x4 wont work, when I shift the lever on the floor it doesn't engage so i bought two new solenoids.. didn't work, have power on both solenoid connections. If I unhook my vacuum lines from the solenoid, I can push the Actuator rod in making my 4x4 work. I've gone threw everything.. have vacuum, have power on my solenoids. Just nothing works when I shift into 4x4 on the floor.
View 3 Replies
My daily driver is a Ford pickup. But we recently acquired a 2003 Excursion.
-5.4L V8
-3.73 rear end
-2WD
It is an Eddie Bauer, and despite its age and 150k miles, it is in really nice shape. It runs and shifts very smoothly. So far, we've replaced the rear glass hydraulics, put 4 new tires and a wheel alignment on it, replaced one brake line from the front to the rear, replaced a cracked rim and one missing wheel hub cap. The driver's seat base cushion leather is ripped, but I procured a replacement leather seat cushion cover which is brand new and a perfect match to the original two-tone leather.
Otherwise, the radio works fine, A/C front and rear is ice cold. The shifter linkage is very stiff and not accurate. I'm guessing the switch selector on the outside of the transmission is failing?
The driver's side power window does not work, and the reverse sensing system has only worked once. The switch always says "off" and if you push it, it won't stay in the "on" setting.
But anyway, here it is .....
View 11 Replies
