Ford Excursion :: 2002 - Running Very Rough And ABS Light Continuously Flash
Jun 30, 2013
I bought my 2002 Excursion 6.8L about 2yrs ago, no less than a week of having it I started to have all sorts of problems. (insert nagging wife here) the biggest of problems was the darn thing started to run very rough and the ABS light cont to flash, then the truck just died (engine stopped, EXTREMELY scary in a intersection) I replaced the VSS in the rear diff.. acted a little better for a while then..no luck. I called around to every ford dealer in town. I need more break light fluid to there isn't enough grease on my wobbler pin?
So I got the initiative to simplify what I was seeing and hearing. I found that there was an OSS sensor on the tail of the transmission...drove my very intense self up to the dealership and bought myself a new OSS sensor. I got home and replaced it, then I drove my truck under the largest shade tree I could find and replaced all the coils and spark plugs. (Insert bloody knuckles and curse words here) Job Done. I thought to myself if this doesn't fix it then I don't know what to do. (I couldn't sell it)...again the point being...the truck has never ran better, gas mileage has doubled and the true power of the v10 has been restored. I found 4 different types of spark plugs in it and 3 different types of coils...?
View 3 Replies
Advertisement
Had the two batteries disconnected on the 2002 Excursion (7.3). Once reconnected, the door actuators all repeatedly lock. They all click every 5 - 10 seconds. Sometimes they click every second for about 5 seconds.
I can't actuate ANY of the door locks on the truck, the switches seem dead. Also, the "door open" LED in the dash is lit. The "THEFT" light is blinking fast as well.
I've disconnected the batteries again several times to see if I can reset whatever is going on. I am keeping a spare key in my pocket because I will get locked out otherwise.
View 3 Replies
The X has been running great, well good enough, lately with no issues. I left work the other morning, and apparently the X didn't want to wake up that early. As soon as I started it up, the check engine light came on and it was running like crap. Had a bad hesitation all the way home. It feels like it is misfiring, but only under load. It doesn't do it if I brake torque it or Rev it up. Only while driving.
The codes I am getting are in the P035x family (typed that way for future searches). P0353 and P0358 are the codes I am getting (along with 4x4 codes for the vacuum solenoid...but that's the solution to other problems not relevant to this!). Being codes for the primary circuit, I popped the hood and checked out the connectors. Both connectors are fine, and tightly connected. I did notice however that cylinders 3 and 8 have other than OEM coil packs on them. These are the only 2 cylinders with those coil packs (they are white and the other 8 cylinders have black coils).
I don't want to just throw parts at it, and I'm not getting a hard miss fire code, just the 2 above. I might try to swap the coils with other cylinders tonight and see if the codes move to those cylinders. It has run like this a few times, but never set a code, and turning it off and back on has "fixed"this in the past.
And just for complete disclosure, while looking for where I saved a password, I found notes from August last year where I pulled codes, and these two codes were present then, with a cylinder 7 hard miss fire code. I replaced the c7 coil with motorcraft cleared the codes, and P0353 and P0358 went away and I haven't seen them since. The plugs are brand new and only have about 1000 miles on them (changed them in September when repairing the misfire and I don't drive it much).
View 11 Replies
My girlfriend has a 2002 F-150 with the 4.6 V8 and I was going to change the spark plugs for her. She said it started running rough and it threw a code and check engine light. She took it for a scan and they told her the number 5 plug was mis-firing. I'm fairly handy and bought a set of the recommended Motorcraft plugs from Rock Auto, AGSF32PM. It also matched the number in the owners manual so I thought I was pretty safe.
Funny thing, when I took the old ones out, they were AGSF22WM's instead. My thinking is they are a colder plug than the supposedly original equipment, but I don't think they've been changed before. They looked well used but the color was good. The truck has about 135K on it.
Long story short, and to get to the question(s), Would there be any reason the factory would have put a different plug in the engine than what is listed? Am I asking for trouble going with a hotter plug than what's been in there (pinging or timing retardation/loss of power)? Am I just overthinking the whole thing and need to put it back together and drive it?
View 9 Replies
The sensor on the dash by the windshield has fallen. I assume behind the dash. The DRL flash intermittently. So I turn my headlights on. How do I find this sensor that has fallen out of place. I assume that's why they flash ?
View 1 Replies
My O/D Light flash some times, no codes thrown. What could cause it?
View 9 Replies
My car is idling rough and the Service Engine light blinks on/off continuously. I ran the codes and they are P0301, P0401 and P1258. What this could be? I changed the plugs, wires and ignition coils about a year ago. Catalytic converter was replaced around the same time but the O2 sensors hasn't been changed. Could that be the cause?
View 1 Replies
Drove fairly fast (160km/hr or 100 miles/hr) then took an exit down a ramp and had to stop at a red light. Noticed all of a sudden that the engine was running bit rougher and then noticed the yellow engine light blinking. I know to turn off the engine immediately when this occurs but then all of a sudden engine light turned off and car was running smooth again.
Car has been reliable for 7 years - proper maintained, synthetic oil, 171000km, timing belt changed, burns very little oil, good torque. Should I have it checked by the dealer (fantastic fair vw dealer)?
View 3 Replies
I own a 2002 Passat 1.8T. The oil pressure light came on a few weeks ago and I took it in to be looked at. The oil pressure at idle and at 2000 rpm's was fine so they thought it might be the Oil Pressure Sender. Picked up the car and lo and behold, the light continued to come on. Took it back for service. This time the oil pressure levels were lower than spec so, they changed the Oil Pump, tested the pressure and all checked out to be within spec. 15 miles into my drive home, the light was on again. Not sure what to look at now. What to do next?
View 3 Replies
Having this issue for a while. Finally have time off work to dig into it some more. 00 ex, v10. Intermittently flashes o/D light and shifts hard. I replaced 2 out of the three speed sensors. One at the output and the other on the axle. Only active code is the p0720 output shaft speed sensor circuit. Last weekend removed and inspected harness, did not electrically measure it tho. My question is: intermittent problem? I drove it today to see if it was still doing it and it drove like a dream! Haven't had the battery disconnected or anything, just sometimes it does it and other times it a smooth ride.
View 14 Replies
I have a 2000 excursion 4x4 v10 with 90k. The past few months I've noticed a tug or miss fire at low RPM (2000 AN UNDER) the past week its gotten worse, some occasional rough idol and the missing is getting worse. Whats wrong?? I don't want to take it to ford yet! No Check Engine Light yet...
View 14 Replies
The X 6.0 was running rough at 1700 rpm and cold it barely ran at all. The dealer did full compression test - pass with no issue. Fuel pressure regulator was bad, they replaced it. They also replaced the fuel filter. That didn't work, so back to the dealer and they diagnosed that the injectors were not optimal for about half of the cylinders. The recommendation was to replace the injectors and they gave me their quote...time for some DIY.
So, I dive in; order and install Warren rebuilt stock injectors (new down tubes and dummy plugs as well). I also went ahead and replaced both oil cooler and screen as well as the EGR cooler with an aFE improved design. I also noted the Turbo was throwing oil into the intake so I replaced the turbo with the PowerMax. Additionally, I replaced the FICM with a BulletProof unit set at 53V. Heck, I went ahead and installed an XPD coolant filter system as well.
Got the X back up and running this weekend and she runs nice, smooth and with authority. So far so good.
This morning I start her up, notice that she isn't running as smoothly. I drive and now the X is not running with that real authority (not as much power but she runs) and I note that some roughness is once again apparent at 1700 RPM.
Obviously, all of this work didn't take care of the root of the problem. What else could cause this issue? Will Rev-X take care of it (I'll get some of that ASAP)? How did she run so well for a few miles and now the problem is coming back?
I have the PHP FICM programmer and am looking to install that next but I doubt that will eliminate the root problem. I don't want to get frustrated so I'm trying to approach this systematically.
View 14 Replies
So I bought an 04 3 months ago everything seemed good all deltas were good had a small leak nothing serious. I had the egr deleted then i did the mistake of flooring it 1 morning at top end and the mech is telling me threw a valve. The truck was stumbling and running ruff with white smoke. looks like cycl. 7 took a hit and shows 10 psi of compression. The injector are in working order and so are the rockers. the bill is 3500 all in for new gaskets and oil cooler head work, arp studs and labor.
View 8 Replies
I have been chasing down what was a perceived vacuum leak...
My Ex (V10, 4x4, 217K miles) started to have an intermittent rough running/no power situation very randomly. No codes on the scanner, and no real apparent cause or condition to pin it down. I noticed what sounded like a like throttle ping...figured it was a vacuum leak someplace in the spaghetti under the hood.
I began to run down the possibilities. I have recently had the entire suspension replaced and upgraded all 4 corners to Power Stop brakes. Figured it might be something related like the classic lines to the hubs.
Replaced the vacuum lines to the hubs - ran OK for a bit, then rough start/idle/no power.
Replaced the vacuum switch for the hubs - ran OK for a bit, then rough start/idle/no power.
Replaced fuel filter - ran OK for a bit, then rough start/idle/no power.
Ordered a new vacuum reservoir...
While waiting on that, changed all 10 plugs and coils. Not. Cheap. Ran OK for a bit, then rough start/idle/no power.
Replaced IAC - ran OK for a bit, then rough start/idle/no power.
As I was getting ready to install the vacuum res, it just croaked. it would turned over like it wanted to start, but wouldn't catch.
Of course.... So, now it had to be towed and yes, the fuel pump puked and that was that. I've never had one do anything but just quit suddenly before, so lesson learned. Evidently these pump can act up for a bit before they die.
View 4 Replies
So Friday before last my ex laid down on me while i was headed to work. So I parked it in a walmart parking lot and caught a ride to work with a friend then had it towed home that evening. Problem i was having is it started running really bad, miss firing, smoking, and sounding real rough, but I wasn't getting any trouble codes. So after both uvch's, icp, ipr, icp pigtail, checking fuel for water contamination and pulling my hair out, i decided to check the oil and found it to be 4 quarts low. Talk about feel like a knuckle head.... While it was down it did receive a new water pump, a diesel site 203* thermostat, new billet thermostat housing, Gooch's Radiator Flush Procedure, and some fresh rotella etc.
View 5 Replies
My 2002 Ford Explorer 4L V6 is running rough I found out why I just don't know what the piece is called because I need a replacement. Mine fell off and fell down the engine and melted quite a bit. Also the part number on my piece doesn't work anywhere, that I have typed it in. Mine has a Ford part number of 1L2U-9F764-AC. Also need to know the proper Ford number. I have a picture I found online with an arrow pointing to the piece I need.
View 1 Replies
When I first start my excursion in the morning, it starts fine, idles fine. If I don't let it sit for about 5mins plus i have this issue. I will start off and it has no power at all. I can barely get up to 20mph. It doesn't seem to want to change gears, I don't hear the turbo spool up. Then all of a sudden it will go to next gear, turbo spools up and it has power again. It is like I said a 6.0 power stroke, its a 2004 excursion with 214k miles.
View 11 Replies
I have two issues with my 2000 6.8L gas excursion. Neither seem to be causing any harm...
1st issue - While its raining, or even just really humid, on a cold startup, my truck runs rough. it almost feels like it wants to die, but doesn't. After about a 1000 feet down the road, it runs normal.
2nd issue - I've started noticing that almost always, I here a whirring type of sound coming from the back. It is not from the brakes, as they are new and the sound is best heard at a complete stop. The sound lasts for about 3 seconds and then repeats after a few more seconds. At first I thought it was the coolant circulating through the pipes that run to the rear heater unit, since the sound sounds a lot like fluid flowing through a pipe. However, my coolant level is normal and the system is tight and I have not had to add any since the only major overhaul in January. At idle, the engine sounds like it isn't idling at a constant rpm, but more like a slight up and down in rpm, but the amount is so slight, it doesn't register on the tach. The only other thing that comes to mind is the fuel pump. Is this sound a sound of imminent failure of the fuel pump? Or is it normal? The truck otherwise runs great at any speed and pulls my boat as well as I would expect it to.
View 5 Replies
I have a 2002 Ford Windstar. Just replaced a TPS, went to town was coming back home, and all of a sudden it started to spit and sputter while in gear. But, in neutral she runs alright. I use mid-grade gas. I put in two cans of Seafoam in the tank. Wrecker operator smelled the exhaust and told me the it was too rich. My question is and this sounds stupid, could the previous owner. Had never replaced the fuel filter or if they did replaced it, that it was installed backwards. I drove it almost 20 miles before it died. I figured that the fuel in the gas line emptied and it refuse to go. And since it only runs good without strain on the engine...
View 7 Replies
Since having dealer work on my brakes: replaced booster and brake light switch. While at the deal the changed all the fluids. Now my EX has been intermittently stalling when stopped in drive with AC running. When it stalled the OD light was flashing. Now we have noticed that the EX is sputtering when stopped while in drive and may stall. Also, itermittently seeing the the ABS light come on. Today it stalled and now the CEL is ON.
View 14 Replies
My ranger just started running very rough. Like misfiring, but I think it may be the fuel pump. It starts and drives...but it surges then drives normal, as if fuel is being fed, then starved, then force fed etc. My father asked if I had trouble starting it and to be honest in the last 6 months it was a little harder to start on several occasions. On a few occasions it required more cranking. But that was only a few times.
I tried putting in a fuel injector cleaner and 93 octane gas but it is still running even rougher now. I changed out the fuel filter under the rail about a year ago (maybe 8000 miles ago at most). My father thinks the fuel pump is shot and he laughed because his went on his expedition and he said it is inside the fuel tank and there is no way to get at it without dropping the tank. Is that true? 2002 ranger xl 4cyl
View 7 Replies
