Ford Excursion :: 2002 - Just After Ride Spring Swap?
Jan 2, 2017
I want some honest opinions on whether a spring swap is worth the money and time to make the ride better and less harsh of ride. I currently have a completely stock 02' 7.3 4x4 Excursion with 204,000 miles. I have been reading a lot on the spring swap and really want to know if it's worth it for the sole purpose of ride and keeping the front off the bumpstops. I don't tow enough to justify it for that reason , and could live without the lift portion because I use it for a daily and family hauler. I experience some sway but not terrible ,but I do believe my shocks are shot as well and I have hit the front bumpstops a few times over railroad tracks.
View 14 Replies
Advertisement
I work at a ford dealership in detroit, im looking into doing a v/b code swap, and just had some questions. my current stock excursion springs are completely shot. so i need new ones so might as well do the swap. do i need to order or get anything other than the v code springs, and the b code springs, new u-bolts, and modify the b code springs? i do not need shackles or anything to have the ex sit level when im done..? just making sure before i get involved. have viewed many topics on here about it and just want a definitive answer. 2005 excursion, v10. i actually wanted to go with the X's in front, but i dont know how to make those level in back.
View 14 Replies
I thought I had come across a chart here that showed you the different spring ratings and the expected height change difference from stock, for each engine option.
View 7 Replies
My leaf spring swap is almost complete... its been almost 3 weeks with all the conflicts of life but its getting near completion. Just have to do front passenger side now.. Tomorrow and it should all be done.. hopefully... Any ways... my preliminary numbers are 40" front (ground to fender) and 41.5" rear.. Might be 1/2" to 1" off since I haven't finished the job AND the truck is sitting on dirt. Any ways, What size wheel/tires can I fit on there now? And will I need a spacer with that size?
View 1 Replies
So this may be a really dumb question, but here goes. I have a new to me 2001 v10 gas 4x4 ex. It has obviously been lifted in the past. The springs seem totally shot as the back end is quite a bit lower than the front and drops dramatically while towing. I am adding a helwig and have a wd hitch but have not set it up yet. So my question is can i do the spring swap? It would seem that i would need to address whatever changes are made from the stock ride but im not sure. I like the current lift and would be fine keeping it and adding the lift from the new springs.
View 14 Replies
I have a 2002 4x2 xlt stock height with 100k miles. I've installed a rear sway bar, air assist bags in rear and bilstein shocks. I am looking for a smoother ride. It doesnt take the large bumps and train tracks very well. It feels like if the front end bottoms out. Ive been reading here on the forums about the rancho 9000 adjustable series giving a better ride, but most of those are for the 4x4 ex's they sit higher and more travel on the front end. So I am wondering if with rancho's make a smoother ride but not the front end bottoming out, maybe a 4" lift with the rancho's would give me both a smooth ride and no more bottoming out.
View 11 Replies
I have a 1992 Aerostar Sports edition. My clock spring went bad like 6 months ago. I couldn't find a replacement anywhere. Not even at the Ford. I went to different junkyards and couldn't find the same exact one. Since I wanted to change the steering wheel anyway, i got the steering wheel and the clock spring from a 1999 Ford Explorer Sport at the junkyard. The clock spring fits perfectly and so the steering wheel. My only problem is that clock spring harness is different. I have no problem with the steering wheel side since both the steering wheel and the clock spring came from the same car. But under the dash is a different story. I have the manual for my Aerostar with the wiring schematic for the speed control system (cruise control) and horn but i just can't find the one for the 1999 Explorer. I got one for a 1996 Explorer and have the same wire colors than the clock springs i got from the 1999 Explorer. But i want to make sure I got the right schematic to feel confident I'm doing the job right. I can also use another version for the 1992 Aerostar because mine is a little confusing.
My old clock spring had two harnesses. One for the airbag which I am not going to use (i don't like airbags) and a second one for the cruise control/horn. This harness had four wires. One thick black one that goes to the casing of the ignition switch, and three smaller wires (BK, LB/BK, and Y/LB). The clock spring from the 1999 Explorer has six wires on that harness. One thick black that goes to the ignition switch and five more smaller ones (BK, LB/BK, DG/O, Y/LG, and R/BK). Going by the two schematics i have them figured out (i think), but want to make sure.
View 14 Replies
What model year(s) 2nd row bench seats that have a factory LATCH system will fit in a 2002 Ford Excursion to replace the seat that is missing the anchors that are between seat bottom and seat back?
View 14 Replies
Any success story on converting 2003 or 2004 f350 with leaf spring front end to the 2005-2007 f350 coil front end is it possible?
View 8 Replies
A couple years ago I did the V Modded B spring swap on my Excursion. The rear was quite a bit higher than the front so I added the 3rd leaf from the old rear springs to the new front and that worked but it is still a bit higher in the rear. I regularly tow one of two different trailers 3000 lb and 5000 lb and occasionally a 20" car hauler 6000-8000 lb. The smaller ones barely squat the rear of the truck. I recently added a Plow and would like to raise the front so it is level with the rear. I need to raise the front about 1-1.5 inches. What front shackle do I need?
View 14 Replies
I'm looking at a pair of springs from a donor truck f250/350. The number on the spring is (rpn 0612 2c34 ca). How to decode this? I know it has an overload top spring. I'm looking for a two inch lift over stock springs.
View 5 Replies
The local shop here suggested getting a set of F350 springs and they would take them apart and a leaf to the front and rear springs.
View 2 Replies
Here is my current situation. No cruise, Replaced clock spring because the air bag light was also on. Still no cruise, checked fuses, they are fine, replaced bulb in gauge cluster. Still no light coming on at all, so I can't do the self test. Do you think my steering wheel switches are bad? Is there anything else I can check?
View 14 Replies
Just had a front spring snap on my front drivers side on a road trip to the cottage. Found a place one hour away that can do new replacement front springs. The question that I have is that he can get F450 equivalent springs a lot cheaper than F350 springs. I do plan on adding an aftermarket bumper at some point in the future. What should I order?
View 14 Replies
I got the new ones, (as mentioned in another thread) and they're the same as the old ones. Well, the one that's still in one piece.
I guess I'm missing something very simple, but as easy as it would be to cut the old one out...how do I make room between the lower leaf and the other leaf pack to get it out?
I about hung from the lower leaf and it didn't move quite enough to give the room to remove the bumper.
View 5 Replies
I am in the middle of the 7.3 to 6.0 swap and wanted to confirm the in and out lines of each cooler. All the links to the websites that were writeups seem to be dead.
View 3 Replies
Replaced front leaf springs to procomp, now i got a clunking noise from right leaf spring rear eye(and a little bit from the left).
Can it be that:
I've tighten them to much? Wrong way (big eye is in front)? Got about 4" lift in front and haven't received rear leveling kit yet so the angel is wrong?
View 10 Replies
Measuring the stock suspension length from bolt hole to bolt hole for me? I want to lift the front of my 05 an inch or two with longer hangers and just want to make sure the ones I have now are stock length.
View 14 Replies
I am looking to swap the worn steering wheel in my Excursion. I would like a wood and leather like the Navigators have. Any tips on doing the swap?
View 14 Replies
I'm thinking about swapping from captains chairs to bench seats in the 2nd row of my 04 Limited Ex with tan leather. I'd like to mount an amp or 2 under it.
View 10 Replies
Finally pulling the trigger on some springs so I can get this work done, Tousely prices were great on the W's compared to local dealers. Here are some questions.
1. I am planning to go with the W springs up front.
2. Can I still use the B for the rear mod, or do I need C's to keep it level? (Or F's)
3. Do I need blocks in the rear, or just the springs on the axle?
4. Do I need the 2" shackle up front?
5. I have dual Fox shocks that came with the ex when I bought it. The prior owner said they ran a little rough. Are they able to be re-valved, or is it cheaper to go with Bilstein?
View 14 Replies
