Ford Excursion :: 2001 - Front Brake Sticking - No Power Assist - A/C Stays On Defrost - Brake Booster?
Jul 22, 2013
I have a 2001 ex. 4x4 6.8 v10. I have been having vacuum issues and brake issues lately. My front brakes seem to be sticking, some times they drag some times the don't squeeze when I step on the brake causing uneven wear and pulling when I stop. Also feels like I have no power assist. I also have a vacuum issue with the auto setting on the hubs, they don't engage I have to manually lock them and sometimes my a/c stays on defrost. And my cruise control doesn't work, the light comes on and love done the self check but it doesn't show anything is wrong. Could I have a bad brake booster?
View 5 Replies
Advertisement
long time ago i had to change master cylinder and the calipers on the fronts and the break fluid well i decided to test it out and see if they were working fter i was done with them then the light on the dash came on i thought its because the floating thing in the master cylinder was not floating which was not the case i dont think its the sensor i also lost my emergency break shoes never replaced em
01 f250 2wd 7.3l v8 diesel straight pipe 310,xxx
View 10 Replies
My wife was driving my 93 Volvo 940 wagon yesterday, and the brakes suddenly lost power, and brake lights went out. I have heard no hissing from the booster, and I have checked the 10 amp fuse on the relay beneath the instrument panel. Hoping (and praying) it is just one of the relays. I have a meter, but not sure which pins to use to check the relays. Secondary issue: the used radiator I bought did not have the cooling fan sensor, so I have my fan on a toggle inside.
When my wife pulled over because of the brakes, she did not turn the fan on. Yup. Overheated. Now the radiator leaks from the rubber/plastic plug where the sensor goes. Any pliable sealants that could withstand the temps? Cash is in very short supply right now. That is my main issue right now, trying to drive with no brake lights. No ABS light, and no brake light coming on on the dash. Bulbs are good. ABS light does not come on at all with ignition, but bulb tests good. Just hard brakes, and no brake lights.
View 7 Replies
A few years ago I (for him) replaced all 4 calipers, rotors, pads, etc....things were good. Just recently he replaced his Brake Booster and Master Cylinder (not sure what led to this), but long story short everything is back together and he doesn't have brakes.
My GUESS is that the system needs a good flush, new fluid, etc....
My problem is I'm unsure how to bleed the ABS system. A few google searched indicate I need a scan tool, but is there another way? Can I jump something.
So my question, how do I completely bleed the brake system on this truck?
View 7 Replies
I have a 99 150 4 wheel drive..5.4 ..auto...110.000 mile.....notice when driving in town in hot weather....when you are on and off the brake petal a lot....stop and go..etc.....the truck starts to hop or bounce....some....I got out ..and notice the right or passenger side front brake seems a lot hotter than the drivers side......but ...when it does that....the steering wheel doesn't pull to one side...when changing pads before ..notice no one side worse for ware than other...thinking it must be sticking brake calipers....they don't do this say on interstate driving even when on and off the petal some...
View 1 Replies
Yesterday, I noticed that my right front brake caliper seemed to be sticking. This morning I jacked up the front end, and could barely turn the right front wheel when it was off the ground. So, I have concluded that that caliper is sticking. So, here is the question(s): what is the best way to repair this (new caliper, rebuilt caliper, or rebuild it myself), do I need to do both sides the same or can I just do the one that is acting up, and should I expect to pay. I have some mechanical ability, but that Haynes manual doesn't make too much sense to me. Getting it professionally repaired is extremely inconvenient, I need to be back at school (300 miles away) Tuesday evening, and probably couldn't get it in to get it done before then.
View 12 Replies
Brake booster failures on 2011 and newer F-250's? I purchased a 2011 last august and the mechanic at the dealer I purchased the truck from stated that he had replaced the vacuum pump, vacuum brake booster and brake master cylinder on the truck just before I bought it as they were bad. Since then I have had two factory Ford vacuum Boosters fail on me. That makes at least three new factory Ford booster assemblies in this truck within the last year. What could be causing the problem? The truck is out of warranty and I am at a loss as to what could be causing them problem. Too much vacuum? Luckily the last two boosters have failed while sitting in a drive through and at a stop light, otherwise I may have had trouble stopping.
View 3 Replies
The power brake booster on our 2007 Toyota Highlander is broken and needs to be replaced. We asked our mechanic whether there are any brake-related recalls for our Make/Model/Year, and he said 'no'. Is this just our particular bad luck, or have others experienced similar problems with this SUV? It was scary. My husband was driving on the highway and needed to make a sudden stop due to a traffic slowdown. The brakes didn't respond, and he needed to slam down the brakes several times to get the brakes to work. No warning, the brakes just suddenlt stopped working.
View 8 Replies
2000 Ranger, see my sig.
Just had to swap out the pads on my truck yesterday. The pedal was pretty mushy and I was getting shaking in the steering wheel when the brakes got warm. Shaking wasn't all the time, only after they had been used quite a bit - say after city use and the brakes had to be applied suddenly. So I popped off the tires and swapped out the pads and replaced the brake fluid - flushed it.
On the driver side front, the pads barely had any real wear and the anti-rattle clip was all messed up. It was installed properly, but it looked like the pads had smashed into it. The rotor appeared to be warped, or at least out of round - but just barely. You could see it wobble slightly in one spot if you spun the hub with the caliper removed. The caliper itself was sticking slightly.
I didn't see any evidence of damage, the brakes flushed just fine although the fluid was incredibly dirty (because I haven't done it in a long while). On the passenger side front, the pads were worn down to the level I would have expected given the mileage. The wear was even.
My question ultimately is this - is the out of round hub the culprit here? Might there be something else going on like a caliper problem? Ultimately I plan on having the rotors surfaced - one of them certainly needs it and with new pads I might as well do it anyway.
View 5 Replies
I know this has been talked about many times and how to solve the issue but thought I would ask some other questions too. Earlier in the summer, I did grease the slider pins as preventative maintenance. I don't drive my truck all that much and when I used it yesterday, (about 30 minute drive) I came home to burning brake smell. I'm wondering if enough heat would cause the caliper to go bad? Should I just grease the pins again or change out some parts?
View 6 Replies
My Sonata suddenly started having front right brake sticking issue. It will happen only after an extended distance of frequent drive & stop. Something like Houston daily ride. So, after the traffic jam mysteriously clear and you can get some speed, starting at 40MPH a high grinding noise from the front (Ceramic brake pads) and the car feels very heavy. The sticking phenomenon will disappear if you wait a little with avoiding using the brakes.
I am going to check it today. So far I know that the sliding pins are not the issue. I recently cleaned them and lubricated them. The front right brake will get hot while the left are just in normal temperature. The brake pedal is getting higher while the sticking is about to happen and happening.
My first guess is the Flexible brake hose. Or maybe a bad caliper. I think if the master cylinder was the issue, I might have more than one sticking brake wheel. I don't know how common it is to have a bad ABS unit causing this issue. It feels really like a build up pressure caused by a valve effect of interior deteriorated brake hose.
View 26 Replies
One of the pistons in my driver side (UK) front brake caliper is sticking, so I've bought a second hand caliper just to fix the problem until I come to sell my pri in a month or so.
View 15 Replies
2005 Toyota Solara my front driver side caliper was sticking and heating up a couple months ago... replaced the caliper and the rotor... still had the same problem. I would drive it, it got hot and stuck, after I parked for a little while it slowly released. Talked to a couple of mechanics and they both said undoubtedly I had a bad flex hose and it was collapsing with pressure and then will release... I changed the flex hose and flushed the fluid and it was immediately fixed...no problems.
Drove the car for a month, went to South Carolina and back and then a couple days ago the same thing started happening. Talked to a mechanic, he told me that the new caliper may have gotten fried from over heating before I changed the flex hose... Got a new caliper today (warranty) exchange... changed it out and still have the same problem. When it sticks I can release the pressure by opening the bleeder valve so it seems like the flex hose issue again... my only thought now is maybe the new flex hose is a bad one and someone mentioned the proportioning valve.
View 9 Replies
I am getting an occasional (though increasingly frequent) 'brake pad' noise from one or more of the rear brakes on my NHW11. Initially it would only manifest for half a minute or so per trip (and would disappear after some braking) but it is now more or less constant. It is a light 'rubbing' noise which you would expect from worn brake pads.
View 4 Replies
I noticed today (smell burning brakes) that my left rear brake is sticking on my 1999 2WD F250. I hear that this is a common problem? Is it usually a defective Caliper or emergency brake Issue? I had my rear brakes done 50k ago with rotors and rebuilt calipers (first set went 130k).... I don't think it was a total clamp down infrared temperature was 275 degrees on sticking brake and 75 degrees on the ones that were not sticking.
View 9 Replies
Have 50,000 mile on my 2011 F350 6.7 and up until today the truck has been flawless. This is my weekend vehicle and sees very light duty hauling fishing gear to my boat (100 miles hwy) and pulling my 7x12 enclose trailer with goose decoys. On a couple of occasions pulling my 29 CC from marina to my home and back. Took truck in for oil change and tire rotation, service advisor informs me I have 2mm on rear brakes and 3mm on fronts. Not sure why rears have more wear than fronts. Schedule to have brakes done for today and now find out that front right caliper is sticky and they want to replace both front calipers. I cannot believe that a 2011 SD F350 with 50,000 miles and of that mostly highway needs brakes let a lone calipers are going bad. Service manger tried to tell me that brake fluid should be replaced every 2 years, to which I responded that I have Ford perform all scheduled maintenance. He went on to say that this is not scheduled maintenance, wtf bs is he telling me, if it is necessary then it would be scheduled maintenance. Truck gave zero indication of stuck caliper, no sound and no excessive brake dust on wheel.
View 14 Replies
My 2001 F150 has the ABS light on. I can startup and it runs thru the continuity test, light off, in park, no problem. Push on the brake pedal, no problem. Put it in gear and the light comes on, before you start to roll. Should mean its not the speed pickups, i checked them for ohms and 5 volt supply to each. I ran the scanner and got P0703 on the extended codes.
That normally means bad pressure switch on the brake booster. I knew that would effect cruise control and external leaks can be a problem, but could that be related to the 703 code ? Both "brake" related ? I am tempted to buy a switch and install. I do have the factory recall harness on the switch. And check for continuity thru the switch. Has continuity, but only a few ohms, not sure what it should be.
View 9 Replies
My 97 F-150 (4.6 L) has developed what sounds like a vacuum leak under the driver's side dash somewhere above the pedals. I can't see anything obvious. It changes sound with various positions of the brake pedal, and I can make it stop with hard acceleration for a few seconds. The brake pedal feels the same. I'm assuming the problem is probably my brake booster, right? Or should I be looking elsewhere? If so, how hard is it to replace?
View 3 Replies
I owned a 1980 Chevy Citation 4 cyl AT. Much is known about the rear brakes locking up with those with MT. There was a recall. On my automatic, however, the power brake assist would often fail resulting in a couple crashes for me. There was an investigation into this in 1983 but I can't find what the outcome was - what the actual culprit was.
View 4 Replies
Have a rusty brake booster? My truck is an 07' with 55k. Brakes work great, but the booster is rusting all over. Should I replace? The lower steering shaft doesn't look so great either.... I'm trying to attach a picture, but I'm having some issues.
View 3 Replies
A few weeks back my rear drivers side wheel started smoking severely...when I stopped you could smell the brake material, feel the heat coming from the wheel, and lots of smoke. I speculated it was the parking brake that got hung up. I jiggled that cable around and then went around the block - no issue. Note: I did not leave the parking brake on.
It happened again a week later, but not as bad. I took it into the dealer today. They said heat was evident as it burned off a sticker on the disk or caliper hsg area. They have not determined yet if it is parking brake or caliper?
View 14 Replies