Still haven't found out the problem with excursion quitting it has stopped for good this time cranks but wont start, fuel pump and filter have been replaced shop said it was going bad, sent to dealer twice no fix.
2000, XLT, V10, 150k, 4X4 .....
2000 excursion V-10. I parked the truck, went back to start it and all my gauges blink, and the number one relay under the dash (interior light relay) begins clicking. The truck will not even crank. The relay will continue clicking (even with the key off) until you remove and replace the relay. Sometimes I will get absolutely nothing when I turn the key. I have tried jumping the battery, no change. Also tried starting it in neutral to trouble shoot the NSS, but it won't even click when in neutral. I checked battery connection, and followed the battery cables to look for a short but found nothing.
View 3 RepliesPeriodically my X doesn't want to start. Doesn't even turn over or crank. The weird thing is, sometimes it acts like the battery is too weak and the radio will flash on or maybe I hear a fast kink-kink-kink sound. Other times, it's just dead, like it doesn't even have a battery in it. Eventually it works again and cranks like a charm. Starts right up.
The ground from the battery to the fender looks good. I noticed the ground from the frame to the body was gone, so I replaced that. Didn't change a thing. I'm reading all the things it COULD be and I'm getting frustrated. I hate electrical problems.
2000 V10 Excursion XLT, 180,000 miles
I have a 2000 excursion with the 7.3 in it. When I turn the key it wont crank over but i can jump the selonoid and it will fire right up. I replaced the selonoid and I don't know what else it could be???
View 8 RepliesTried starting the Ex for the first time in two weeks and it won't start -- no starting problems before. Battery is 4 months old and fully charged. When I try to start it electrical power is there (gauges act normal) but no crank at all -- motor does not turn over. Its acting like a switch or some electrical connection is bad. I tried moving the gear selector around to make sure it is in Park....... also tried starting it in neutral but no luck.
View 4 RepliesMy Excursion didn't start the other day. It would barely crank. A new Interstate battery was installed about a year ago.
I jumped it and it fired right up. I went inside and left it running for about 20 minutes.
The next day I started it up and drove about 5 miles. I noticed whenever I was braking both the audio and lights on the radio would cut out.
It sat for about 4 hours and then wouldn't start again. I jumped it again and stood next to it while it was warming up.
I noticed the interior lights got dim, the radio cut out again, and then the entire gauge cluster went crazy. The needles were jumping around and would then shut off, then jump around again. Whenever I increased the RPMs the problems would stop.
I got home and it sat for about an hour. I tried to start it again and it would barely crank.
I'm trying to avoid a trip to the parts store to have the alternator tested since I'll have to jump it again... and worse, I could get stuck on the side of the road if it completely dies.
I'm guessing the alternator is shot. Could it be anything else?
My 7.3 won't start after sitting for almost 2 months, the wiring for the injectors was bad, and the first package was damaged, so I had to order a new one, and wait trough Christmas before I get the new parts. The valve cover seals have now been installed, and all parts fitted. Thieves stole my batteries so I had to buy new ones there as well.
When I tried to start it, it will crank, but not start, white smoke comes out of the exhaust, and glow plugs seem to be fine. One thing I did notice is that the fuel pump under the driver side of car was making a wired noise when turning on the ignition, it was not a constant hissing sound that I used to on my other cars. I poured a small amount of condensation remover in the tank, the tank is half full, but still no start.
After trying a few times, it did sound like it would get better, but that only lasted for a second. Strange problem, I think my fuel pump is acting up, but I don't know for sure yet. The fuel pump did work when I parked it. Could it be a fuse that does it? I checked the hpop to see if there was any oil there, and it was.
I am having a starting problem with my Excursion. It cranks but immediately quits as if the entire engine jams or locks up. I thought it was the starter so I replaced the current one with the original starter that I happened to still have from a previous starting problem. The problem persisted. What the problem could be?
View 12 RepliesI own a 2003 Limited with the 6.8 V10. I drove the truck on Sunday and all appeared to be fine, gas gauge was setting just under a half tank. When I went to start it yesterday, it would not start. Strong crank, no start. I checked my fuse and it was fine. Fast forward to this morning, since I had kind of depleted the battery with attempting to start, I put my little jump start pack on it and gave it a whirl. Truck started fine but the gas gauge was sitting on empty. I had five gallons of gas in the garage so I added that to the tank then drove to the local gas station to add more fuel. I put another 10 gallons in the tank so it should have roughly 16 or 17 gallons in the tank. Gauge shows 3/4 tank but miles to empty is right around 175 miles which would seem right with 17 gallons in the tank. I suspect the fuel pump. I don't really want to spend $500 on the Motorcraft unit but was wondering if the group believes the Delphi or the Bosch units are quality replacement parts?
View 7 RepliesHaving some problems with my truck.... First off I bought a 2002 excursion and drove it for one day. Then I was at the car wash cleaning up the truck. Then I saw the window fogging up so I turned the car off. Now it won't start.
I had previously installed a new stereo, but had some problems, so I ran the remote wire to the fuse box, because the wire in the harness wasn't getting power.. So after a little trouble shooting we found out that the fuel pump wasn't working or was bad.
We replaced it, now it has pressure but will not start, will start with starting fluid but will not crank on its own. someone told me it may be a bad PCM? and a dealer can only replace it... I don't have tons of cash, as i bought this truck on 8/30/12 and this happened the day after i bought it.
The previous owner has paid or the fuel pump replacing but I don't think its right on my part to have him pay more money as this may be a mess up on my part with hooking the radio up to the fuse box... we have tried the fuses,realys, crank sensors...
I have a 2000 V10 4wd. I'm going to list what happened in time order to best describe this problem. Sometimes when key is off there is a clicking from under the brake proportioning valve and sometimes a 2 second long buzz. When this happens, the A/C blower motor can run with key out also. If mistakenly left on over night it kills the battery.
I also notice that sometimes while driving my airbag light comes on randomly and sometimes it dings with doors closed. Also a few weeks ago the overdrive light starts blinking every few days. A few weeks later it wont start. No crank. So I put in new starter because mine was looking pretty crusty. Still no crank, but if I jump connection on inner fender solenoid/relay, then it starts fine.
Next day I put in a new solenoid/relay on passenger inner fender. Cranks fine and starts fine for the whole day until it randomly begins cranking by it self. With no key in. It did this several times even after re-checking everything and cycling key switch to check for bad connection there. The trans starts shifting hard, like the line pressure increased and sometimes it growls a little when it shifts into 4th
I then figured it was the Digital Trans Range Sensor which only allows start signal to go from key switch to the inner fender solenoid/relay if the trans is in park or neutral. I tested the DTRS and it seems to be working fine. It only has power at the solenoid if its in park or neutral on the tan/red wire, but the wht/pnk wire has power even when not cranking.
Being I couldn't figure out why it had power, I cut the red/lt blu wire at the ignition harness and ran a wire from the key switch side to the solenoid. Cranks and starts fine for 2 days and no mystery cranking either. Then after my wife had it all day acting fine I go to leave work that night in the rain after working a 14 hour day..... no crank. I noticed the "THEFT" light blinking but I've noticed that before and never had an issue starting.
When I came back to work in the morning it cranked and started fine 3 or 4 times then crank but no start again. I reconnected the crank wire back to factory thinking I bypassed something necessary. No change. Still acting randomly. I just ordered a VSS for the rear axle and a new DTRS for the trans. Gonna put these in today and test. Next will be a key switch since I'm having things work with key not on and I have 8volts on my grey/yell Accessory wire with key off.
I found a relay that clicks when inserted in it's socket even if key off. Its located driver side by Firewall by the Brake Booster. It has a tan/red wire(same as activation wire on inner fender solenoid but doesn't effect starting.
I have a schematic of starting system but I can't post pics because new acct here. The starter wire is red/blue at Key Switch then wht/pink after Central Junction Box, then dk blu/org after CPPJ clutch pedal position jumper(mine is auto trans. thats why is has factory jumper) but then turns to wht/pink before the DTRS then tan/red out of DTRS and at solenoid(I'm not sure it goes direct from DTRS to solenoid but color stays). As mentioned earlier, the white/pink wire has power but it shouldn't unless cranking, so its either getting it from the CJB or from where it changes from dk blu/org to wht/pink. Is there anything between the CJB and the DTRS? If nothing then why does color of wire change, and what could be giving the wire power?
Just as a note, in case it matters....my interior lights don't come on when door is opened but when it is open it dings like the key is in even when its not.
Black Beauty finally gave up. Replaced battery, replaced fuel pump relay. Would only run with starter fluid sprayed into the air intake. She'll crank but not start. Here she sits at the dealership.
View 14 RepliesI have a 2001 Excursion 7.3 Diesel that is having a starting issue. Have replaced the batteries, has new glow plugs, common failing cam position sensor replaced once already. It runs great when it starts, no codes. It will crank, but not turn over at random times. Will do this for 3 or 4 tries...charge the batteries, go back later to start and it will on the second try. Turn it off, try again..and back to cranking, but not starting. Not fun having to worry about being stranded somewhere. Absolutely desperate at this point.
View 4 RepliesI have 2000 Ranger 4.0L 4wd, 5sp ...
Just in the last month or so as out temps have been dropping off I've been having troubles getting her started. It happens both when the engine is cold, ie first start of the day, and after starting when warm. It did it a couple times last spring, but then all summer and fall I didn't have any problems (warm outside air temps) but, now its happening again. I'd say any time the Outside air temp is 40F or less, I am worried it won't start. IF i get her to start, everything else is just fine and she runs like a top. Here are the symptoms and what I've done so far.
When I crank I will get a couple cylinders to fire for a second or two then it falters out behaving like fuel starvation. Then I crank again right away and nothing fires... just cranking over and over. If i wait a minute and crank again same symptoms or it will fire right up. Baffling!
I thought Idle Air Control valve and sticking fuel pump relay, so I threw new parts on, but no fix.
About 75% of the time if I turn the key on, hear the fuel pump running, turn key off and on, hear the pump again x3 and then attempt the start it is successful.
Unfortunately, I don't have a code reader, or fuel pressure test equipment. The check engine light is NOT ever on. DO I HAVE A FALTERING FUEL PUMP??? I've heard thats tough to change out.
I got a 2000 7.3l with 400,000 miles on it that decided to just not start anymore after I parked it for a couple days. Its always been a hard starter due to needing glow plugs but I can deal with that. it doesn't even try to fire anymore. I replaced the CPS (my tack bounces when cranking). The ICP has oil in the plug so I just unplugged it for now till I replace it.
I pulled the IPR and cleaned it really good and bench tested it with 12 volts and could here it clicking so I put it back in. I can get under the drivers door with the key on and hear the fuel pump running. I gain oil pressure on my dash gauge when cranking. I check all my fuses. my WTS light comes on . I just don't have any fancy scan tools to make this easier. Also just cause I was feeling lucky I just went out and bought 2 new batteries for it yesterday so we are good there.
Found icp sensor with oil in plug and codes p1211 and p1212. Icp sensor reading 0 pressure. Changed out icp sensor. Still cranks no start check oil level in hpop resverior, check with brake clean spray nozzle and no oil on it. Filled resverior with oil. She tried to start. Had to put the charger on her and she finally lite off and came to life. Questions, how would that resverior empty out? Was it because I pulled that sensor? Is there s check valve in that resverior hanging up?
View 2 RepliesI have a 2000 F350 7.3 ... A couple weeks ago I noticed that it was taking longer to start then it should be. Now I have to cycle the key switch 3 or 4 time to get it to start. There is a clicking coming from the relay block under the radio. Sometimes the truck will start sometimes it has to be rolled off. I have recently replace the starter and alternator. I have had the batteries tested and they are good. I replaced the two small relays in the block under the radio, one is for the fuel pump and the other I understand is for the door locks? I also read on here the large blue one is for the turn signal so I have not changed that one. After all this I still have the same problems.
View 9 RepliesWe just bought a 2000 F350 knowing it has some issues. The #5 fuse (generator/secondary) under the hood consistently blows fuses the second it's inserted, meaning there's a dead short. Truck will crank but not start. As well, theres a 5 amp fuse under the dash, which when inserted, keeps the instrument cluster on as if the key was on, even with no key in the barrel. We cannot hear the fuel pump running, the fuel reset switch is fine, all ignition wires at the column are showing 12 volts at the right times. What could be wrong? I'm a 12 volt specialist, but not a ford tech.
View 6 RepliesI've had a lot of problems with this truck and strongly believe the pcm is bad so i bought a used one now it wont start. Just to let you know i did put old one back in to see if it did run with it and it did. I spoke to the dealer they say I have to bring it in to program it for the PATS. I know its got to be programed but does it have to be the dealer.
View 10 RepliesI have an intermittent problem with my 2000 Ex V10 with factory remote start. Sometimes when I put the key in to start the truck, I get nothing. I believe the theft light flashes but I am not entirely sure. Sometimes after a few tries with turning the key it will start. If I hit the button for the factory remote start it always starts, so I have never gotten stuck anywhere.
This issue could happen 2 or 3 times in a row and then not happen again for days or weeks. It's been going on for a couple of years now. What to look at. There is no telling when it will happen again though.
BTW, I have stomped the brake pedal and I have moved the gear shift when it happens and sometimes on retry it starts and sometimes it does not. When I just keep trying the key sometimes it eventually starts too, so I do not think it is the safety in the brake pedal or in the shifter, but I could be wrong.
I recently caught up on some maintenance with my truck, changed the turbo pedestal seals, replaced both batteries, brakes, e-brake cable etc and installed new 10k hid headlights. its a single cab 250 with a 7.3 and zf6 4x4 with 133k. a couple days ago I turned on the headlights and the truck died, restarted no problem and would die the next 5 times I tried to turn them on, then it worked fine. yesterday I got in my truck to leave for work and got no wait to start light, no glow plug chatter, no fuel pump running. turns over just fine but no fire.
I got a ride to work and tried it when I got home, fired right up. I pulled the pCM, checked it out, no weird smells and my TS chip wasn't corroded or anything like that, worked fine. drove to 711 to get a 6 pack and it did the headlight thing again. I removed the HIDs because this all started after I installed them and reinstalled my silvanias and it didn't die when I turned them on. this morning went to leave for work, same no start condition. I disconnected both batteries for 30 seconds to reset anything and same problem. I was about ready to light it on fire this morning.