Ford Excursion :: 2000 XLT Pulls To The Left
May 15, 2015
I have a 2000 XLT, V10, Auto, 4" suspension lift on 315/75R16. It recently started pulling to the left and has been getting worse. At <5mph the steering wheel will pulse to the left almost a quarter turn if you let it go and hold there. At actual driving speeds it feels like a constant pressure. The tire appears to have a wobble to it when driving, I know this because my wife drove followed me in it so I could observe.
It also turned easier to the left than to the right when I jacked up the front end and both wheels spun with ease. I have checked the tire rod, drag link, ball joints, and wheel bearings. They all checked out. The last things I can think to do would be to check the steering stabilizers, I have the dual inline set up, or swap the front tires and see if the problem moves from left to right.
View 7 Replies
Advertisement
2001 Ex 7.3 4x4 with 4" lift (6" with 37" Pro Comp tires)
All new front end steering components.
All new Shocks (bilstein)
All tires properly inflated to same PSI
All new brake rotors, calipers, caliper mounts, and pads.
When under hard acceleration the vehicle pulls to the left and I have to compensate by steering to the right. Under deceleration the vehicle pulls to the right and I have to compensate by steering to the left.
I am about to change all four brake lines to Braided Stainless Steel lines, replace all leaf spring bushings with polyurethane, and install a rear anti-sway bar. I'm going through this methodically enough or am I just building a brand new truck one part at a time?
View 14 Replies
My 2000 ranger in 4x4 high never did this. And in 2wd it doesn't pull at all...
When in 4x4 high it pulls hard to the left ?????? is left not working? It has automatic hubs ...
View 3 Replies
My 2003 F250 6.0 pulls to the right when driving at any speed. In order to keep it going straight the steering wheel must be slightly tilted to the left, not much but a little. When the brakes are applied hard it will go to the left slightly if you are not holding the wheel good. Neither of these are terrible, just a nuisance. I'm worried about uneven tire wear too. One front wheel bearing was replaced a few weeks ago. It had this problem before that and still does after. Does this sound like an alignment or maybe something more?
View 13 Replies
2004 accent manual shift. car drives well, but when i step on the gas, it sudenly pulls to left. when i release gas, it goes back to straight driving. motor mount??? anything else come to mind??
View 1 Replies
I have a 2000 Excursion 2wd. The left front wheel or something up front is making a rubbing sound when I turn to the right. Checked the brakes, they looked fine. Pulled front rotor off and replaced the wheel bearing just incase. Still making that same noise? I can't see any sign of something rubbing either on the frame, brakes lines, or control bars?
View 3 Replies
02-F150-4.2L-102k. Truck was rolling down the road at approx. 35 to 40 mph. A speed bump/table appeared out of nowhere and was hit before beeing seen. Immediately since this event, the truck pulls to the left while applying the brakes. It pulls very hard and is fine while rolling down the road. Is there some damaged steering component or did one of the calipers go out from the jolt?
View 4 Replies
So I've been noticing the truck pulls left when under braking. So, I replaced the front calipers. Now, it still pulls left. When I got home I felt the discs on all corners and found three about the same, barely touchable, and the front left a little warmer. So, it seems its braking more, but its brand new. So, what should I do? They are also pulsing a little.
View 14 Replies
Just as the title says I'm getting a good pull to the right when braking. Little background, truck has 155k, rotors and pads replaced 10 days ago, new tires today. Now with the new tires the pull is more pronounced than with the old tires but has been there, which I thought was just worn out rubber, apparently not.
All caliper pins are greased and moving freely, and for kicks I replaced left pins to see if some how they were fouling up, they weren't, still pulling. So my question after searching is maybe the last two culprits are bad caliper or bad hose? I just wanted to bounce this off the board and see if I am on the right track to fix this issue.
View 4 Replies
Just replaced break pads and rotors. Inner pad on left side was gone leading me to believe slides were not working properly. Pulled apart, cleaned and greased everything, and replaced pads and rotors. Calipers seem to be working fine. Now when I break hard, the truck pulls badly to the left. When I break softly, it seeks normal. My front end is a bit out of whack and veers just a bit to the left. Do you think this is my issue with the breaking ? I'm getting new tires and an alignment soon but was just curious.
View 3 Replies
My 2012 f350 6 lift when I push the brakes it pulls to the left kinda bad and the steering wheel is off to the right..
View 4 Replies
Truck pulls to the left while braking, pretty bad. So, pulled the front right wheel off thinking the pins are stuck again as last year. Bottom pin was fine, top pin pretty gummed up but not froze so I cleaned it up good, used thin layer of the good stuff, put back together and test drove........same thing. Pulls left upon braking just as bad as before. Caliper pistons seemed fine, didn't take much to compress them either. Would a right rear cause this?
View 14 Replies
Had mechanic check suspension components, alignment is fine, nothing looks damage or needs to be replaced. Tires are 35 inch and practically brand-new...
View 3 Replies
I've been replacing my steering components over the past month and have fixed all the previous issues other than this one that's got me stumped. After I make a hard left the steering will pull left (very hard) until I either turn the wheel right or hit a bump. Sometimes when going immediately from a left turn to a right turn (or vice versa) I can actually feel a slight pop as it starts to pull.
The order of repairs thus far has been: new power steering pump, new inner & outer tie rod ends, professional alignment, new steering box with both lines. The shop and I both agree the ball joints are good. I've jacked my truck up by the frame and removed the wheels to check for steering/suspension play but have not been able to find any. 180k miles on the chasis.
View 6 Replies
Well just called it quits from working on the truck tonight. Had some issues with my brakes going to the floor and pulling to the right some, so I went to auto zone and bought all new pads. Didn't think it was time yet because I just replaced the rotors, pads, calipers, maybe 20,000 miles ago. When I got home and everything pulled apart I looked at the pads on the truck and they still had 60% life. I looked closely and noticed that the guider pins on the caliper bracket (front drivers side) were seized. I figured this is what was causing my truck to pull. Looked on the passenger side and it looked similar. Went back to auto zone and returned the pads and bought new brackets for both sides. I got the drivers side replaced and working and all seemed well. I got to the passenger and had a hell of a time getting the pistons on the caliper to compress so I could get it off. Once I finally got it, I noticed the pins on that side were not seized. I bought 2 sets of guider pins so I took the old ones out and greased up the new ones and installed them. Put everything back together and took the truck for a drive. Everything seemed normal at first, but once I got on the highway and hit the brakes, my truck pulled to the left. HARD.. Im assuming this is because of the pistons on the passenger side caliper I was having a problem with, not having the piston compress all the way causing my truck to pull. While I was looking at the caliper, I also noticed what '"looked" like a grease fitting, and also a bleeder valve a few inches away from it. Am I crazy, or is that fitting for bleeding the brake lines also...?
View 5 Replies
1999 F250 SD 4x4 7.3 PSD ... My truck has 198K miles on it. It pulls to the left as I drive it. So I took it to a shop to have the alignment checked. They told me that the front outer tie rod was bad and needed to be replaced. And of course they said they needed to put in a set of caster camber bushings to do the alignment. They quoted $400 to change the tie rod out. I said I would do that. They gave me the print out from the alignment but reading it the only thing that was out was the toe. Left tire was toe out and the right tire was toe in, which to me would cause it to pull to the left.
I got under the truck and the steering link, piece that goes from steering box to right side/tie rod, is not tight...I can move it up and down and it clunks when I roll it up. I have a clunking noise when I drive it and go over bumps also. Could this be the clunking noise? Also, if I replaced the ends of the steering link, that would tighten up but possibly push the steering back to the right some to straighten out the tires? I have read alot of threads talking about the clunking being tied to the sway bar bushings being bad but the clunking I get by rolling the steering link up and down sounds alot like the noise I am hearing.
Also, when looking at the axles where they go into the knuckle, there is a loose plastic ring on both sides. Is this part of the dust shield or an oil seal?
View 5 Replies
So my 01 has been parked in the garage for about 2 months. Normally on battery tender but it accidentally got unplugged and I didn't realize til yesterday when I went to start it. So I got the battery charged up and put air in my rear drivers tire since every time it sits it goes flat. Well I did all this I so I could take it to get tires today.
Driving to work and its shaking pretty bad at highway speed. Don't recall it doing this yesterday. Never really did this before either. The truck also pulls hard to the right. Its done this for a while so I'm not sure if it's just the tires or needs alignment or something else. Or all of the above.
I'm mainly concerned with why it was shaking. The front tires don't look low however I will check the pressure on my lunch hour today.
View 13 Replies
My passenger rear door handle opens at almost end of the pull if that makes sense. This is different than the others. Is there a way to adjust it?
View 2 Replies
I put on a new set of tires (X Radial) at Sams Club with installation plan which includes balancing. I also brought the car to the dealer to have alignment (front I guess) done. The car goes a straight line no matter what except it always pulls left if I release the steering wheel when I brake from a high speed.
View 7 Replies
Well, I tried this Death Wobble Kit on my Ford F350 Super Duty from a company called WC Motorsports. Had it installed at a Ford Dealership. DO NOT BUY this kit. Missing parts right out of the box. Also makes a horrible clanking noise after install. Piece of junk. Possible fix to one problem only to have multiple other problems:
1. Clanking Noise
2. Truck pulls to the left
3. Have to cut the factory subframe. (Never a good idea)
4. Changes the degree (not recommended by Ford)
View 10 Replies
2000 jetta vr6 145k.
So when I bought this car it was not driving and hasn't been driving for a year or so, needed time chains and the whole 9 yards. Did that, everything is up and running as well as new brakes all around, snow tires until I can afford some all season.
While driving, only in gear, the car pulls to the left. Even with a touch of the gas pedal it's pulling left. As soon as I let off its going right. If I coast in neutral it holds straight like an arrow. I have replaced the bushings for the dogbone and trans mount with polyurethane thinking with the high mileage it would be the culprit. The control arm bushings seem to be ok, neither side has any play, no wheel bearing play, no tie rod play....so I'm stumped.
View 13 Replies
