I have a 2000 excursion 4x4 v10 with 90k. The past few months I've noticed a tug or miss fire at low RPM (2000 AN UNDER) the past week its gotten worse, some occasional rough idol and the missing is getting worse. Whats wrong?? I don't want to take it to ford yet! No Check Engine Light yet...
View 14 RepliesI recently bought a 00 Excursion v10 2wd everything looked right no major problems. I noticed it has a rough idle and i thought it could be the EGR i went under the hood and there's no EGR in sight. I plugged the OBD reader to see if it would give any codes since the there was no check engine light on and wanted wanted to make sure it worked, It showed a P0304 code its Cyl4 misfire i checked plugs/coils and i noticed there's a little insert inside Cyl4 plugs hole in the head that it has the plug screwed on. I decided to change all the plugs and the coils and i still have the rough idle and code i can hear a ticking noise around the engine in the passenger side.
View 7 Replies2000 4.2....Last year I had to replace the coil pack when it started running rough and had a code for a misfire on cylinder 3. It is doing the exact same thing now, same code, same cylinder. Is there something wrong that is causing this?
View 5 RepliesI have a 2000 LC that has a few symptoms - intermittent misfire/running rough at these times it has:
dark smoke
uses 3 times the fuel
loss of power (to normal)
will pick up revs slow without running rough and runs normal at high revs.
dies misses and then picks up revs slowly when accelerator is pushed fast to the floor from idle.
Hyundai mechanics checked computer and it coded change spark plug leads this did not fix the problem, and have no idea.
About 6 months ago the car was doing the intermittent thing when it died and liquid was heard splashing on the ground. I found the main petrol line connecting to the pump had come completely off. After replacing all problems ceased and the car ran perfect with full power etc.
I've checked the fuel lines none appear to be leaking etc.
Okay so last year i bought a 2000 celica gt manual with 50,000 miles, and currently has 67,000 miles. A few days ago I started to notice the engine was running rough and then about 10 miles later the chack engine light came on. I promptly went to the auto parts store to read the code. I was informed I have a cylinder 1 misfire. Naturally i replaced the spark plugs with NGK iridium, reset and rechecked engine code. Same code. Next i swapped the coils from 1 and 2, reset and rechecked. same code. I then swapped fuel injectors from 1 and 3, rest and rechecked. Same code. So now i am a bit stumped.
Only faulty equipment prior to this incident would be 2nd gear synchronizer. Only applicable above 5,800 RPM.
I have two issues with my 2000 6.8L gas excursion. Neither seem to be causing any harm...
1st issue - While its raining, or even just really humid, on a cold startup, my truck runs rough. it almost feels like it wants to die, but doesn't. After about a 1000 feet down the road, it runs normal.
2nd issue - I've started noticing that almost always, I here a whirring type of sound coming from the back. It is not from the brakes, as they are new and the sound is best heard at a complete stop. The sound lasts for about 3 seconds and then repeats after a few more seconds. At first I thought it was the coolant circulating through the pipes that run to the rear heater unit, since the sound sounds a lot like fluid flowing through a pipe. However, my coolant level is normal and the system is tight and I have not had to add any since the only major overhaul in January. At idle, the engine sounds like it isn't idling at a constant rpm, but more like a slight up and down in rpm, but the amount is so slight, it doesn't register on the tach. The only other thing that comes to mind is the fuel pump. Is this sound a sound of imminent failure of the fuel pump? Or is it normal? The truck otherwise runs great at any speed and pulls my boat as well as I would expect it to.
So I just had both cats replaced and now the car is running very rough and trowing out mis-fire codes. What could cause this? Going to disconnect the battery to reset the computer to see if that might work.
View 8 RepliesI have had some slight rough running with a cold engine and stumble <2000rpm. Finally it tripped a CEL which was read as a misfire code.
The mechanic swapped the coil and plug(recent) and no change. He did a compression test and air blew out the exhaust. So.......the car needs a valve job which entails motor removal and fixing the head and reinstall. He rough estimates this at $2000 and rate is $65/hr.
He mentioned looking at pistons and may be a bit more if rough.
This car well maintained (170,000 miles 2005 Legacy turbo wagon with manual)...
98 5.0 last week i was driving around for a few hours and everything was fine. Did some work in the garage for a few hours and had to run to the hardware store. Started the truck up and she ran like crap. Engine shaking like a misfire. First thought plugs and wires. Well by then it was late and Easter was the next day didn't get to it till Monday. Well after the change still crappy running.
So I changed the fuel filter and cleaned the mass air. No change. Checked for spark on the coil packs all have spark. Checked the PCV all good there. Checked for vac leaks none found. During that I noticed a small hole in the EGR tube I repaired that but still running like crap backfiring out the exhaust, engine shaking badly at times. I also changed out the FPR on the fuel rail. No change of course.
As of today I changed the coil packs. Again no change. Only code it throws is a EGR high flow after I fixed the hole but was having problems before that.
2003 Ranger FX4 Flareside
4.0
Automatic
145,000 Miles
Here's my issue: My Ranger has been running like a dream until yesterday.
I took off on a parts run for my sons Ranger. I got to a stop sign and as I stopped, it started missing and barely running. I nursed it back home and checked the flashing CEL. It was giving me a misfire on #3.
Since I had been planning on changing the plugs and wires, I dove in and got it done hoping that was the cause of the misfire.
Started it up, same thing. I went to the next obvious item: coil. Replace it, still running like crap. Gave up for the night.
Today, I thought I would dig in using the tips here on the forum. Did the spray down...no errant spark anywhere. Tested fuel pressure: 65psi no drop in pressure on acceleration.
Started pulling wires off the coil one by one. Four of the wires resulted in running worse. 2 had no effect. #3 and #6. The coil was producing plenty of spark on all 6 ports.
At this point I was sure it had to be 2 bad injectors. Since I couldn't get injectors tonight, I moved them around after cleaning them a bit and tried my wire test again. The problem stayed on the back 2 cylinders!?!
I tested for voltage on the back injector plugs and I am getting voltage. I also used a stethoscope to listen to all of the injectors. The back 2 seem to remain silent. I have also unhooked the battery for 20 minutes to reset the PCM. Still missing and running rough....
Here's a list of what I have done:
Autolite Double Platinum APP5144 plugs. .062 gap
Autolite Pro Series wires #97051
BDW E97P Coil
New air filter
What should I do next? I really don't know where to go next.......
I just bought a 2007 F150 XLT with a Triton 5.4 with 80,000 miles on it. My problem is this, the engine seems to run ok ( a bit rough) until it gets up to running temp and I have driven about 10- 20 miles then most of the time, it starts to act up.
When I am driving it is fine, but when I slow down and come to an idle about 500rpms, it sometimes runs very rough, sounds like a diesel and shakes violently. It feels like it is doing damage. Sometimes it stalls. If I rev it back up immediately it will smooth out.
In speaking to some friends they've suggested things from plugged oil channels, (affecting the cam phasers? All the way to it needing new chains, phasers and guides. I don't want to spend a ton of money doing an improper service repair only to have the issue show up later . But there seems to be a lot of different answers to the same problem. Is the dealer going to be able to diagnose something like this fairly well? Or should I try to narrow it down a bit first?
My wife's car suddenly started running rough. 2005 Taurus, 6 cyl, 3L, OHV, 83K miles. CEL came on and code came back as "P305 - cylinder 5 misfire detected". As a side comment, her tachometer has been fluctuating big of late as well.
View 2 Replies1990 Ford Aerostar. When I start runs really rough and has excessive fuel consumption and the exhaust smells like gas and has a misfire my friend says its the coil pack going bad im not sure. I love my ford aerostar dont wanna get rid of it.
View 5 Replies126000kms on 03 explorer 4.6 truck started. Running rough at idle and under load.... Code came up for cyl 8 injector. Replaced injector... problem still there. Switched cop and plug with another cyl and plug.... same code and cycl 8 is definitely not working. Would a generic problem always affect i cylinder. I even checked wire clip on for injector... it appears ok. There is power to injector wire clip.
View 5 RepliesI have a buddy at work who has an 04 f350 6.0 that is running very rough. we put a scanner on it and disabled the injectors and 1,7,8 have no change. He checked the FICM voltage and is getting 48 volts on crank and run. He checked the wiring for anything loose or rubbed but nothing seems wrong.
View 14 RepliesHere is my situation : I have a F150 1999 4x4 ext cab with 326 000 km. A little while ago I got a P0401 code so I decide to clean the TB first and at the same time change plugs and wires since they were overdue. The same code came back and a misfire. Ordered EGR valve, DPFE sensor and selenoid. Realize that I had ordered crappy plugs by mistake. I change all plugs. Had to wait for the EGR valve and others to arrive. I drove the truck for a while since I did not have the time to change the valve and others, during that time the misfire did not come back. Yesterday I change the EGR and others. Today I get a truck that runs really rough and got new codes , P0305 and P0174. I'm really confused now on what should be my next step, should I change the coils, can a P0305 cause a P0174. Should I change vacuum hose going to the EGR , selenoid and DPFE.
View 12 RepliesI have a 2003 ranger and have had ongoing problems with misfire cylinder six and have had three different mechanics diagnose the problem as a bad ground. I have replaced all plugs, wires, coil pack, injectors and am constantly pulling the plug on cylinder six, cleaning and often replacing, I also disconnect the battery so it resets the check engine light and it runs fine for about 100 miles and starts running rough again and on goes the check engine light. I have 134000 miles and have maintained it since new.....
View 4 RepliesMy 740 (1990, B230E, non-turbo) has been running rough at low rpm. Once above 1800 rpm or so it's fine. I've changed the Distributor cap and rotor arm (they were both shot), but the problem persists. I'm thinking injector relay or ignition stage amplifier next, but I don't want to just through parts at it.
The plugs were changed 3 months/1,500 miles ago. The misfire is intermittent.
The X 6.0 was running rough at 1700 rpm and cold it barely ran at all. The dealer did full compression test - pass with no issue. Fuel pressure regulator was bad, they replaced it. They also replaced the fuel filter. That didn't work, so back to the dealer and they diagnosed that the injectors were not optimal for about half of the cylinders. The recommendation was to replace the injectors and they gave me their quote...time for some DIY.
So, I dive in; order and install Warren rebuilt stock injectors (new down tubes and dummy plugs as well). I also went ahead and replaced both oil cooler and screen as well as the EGR cooler with an aFE improved design. I also noted the Turbo was throwing oil into the intake so I replaced the turbo with the PowerMax. Additionally, I replaced the FICM with a BulletProof unit set at 53V. Heck, I went ahead and installed an XPD coolant filter system as well.
Got the X back up and running this weekend and she runs nice, smooth and with authority. So far so good.
This morning I start her up, notice that she isn't running as smoothly. I drive and now the X is not running with that real authority (not as much power but she runs) and I note that some roughness is once again apparent at 1700 RPM.
Obviously, all of this work didn't take care of the root of the problem. What else could cause this issue? Will Rev-X take care of it (I'll get some of that ASAP)? How did she run so well for a few miles and now the problem is coming back?
I have the PHP FICM programmer and am looking to install that next but I doubt that will eliminate the root problem. I don't want to get frustrated so I'm trying to approach this systematically.
I'm having an issue with a 2008 Passat 2.0T. Engine ran rough one day and check engine light came on! I get the VagCom out, scan the ECU and get misfire on cylinder #2 and #4. Car has 109 000km. Plugs were never changed so I order some new OE Bosch platinum iridium plugs. Go for test drive after having change the plugs and I still get misfire on both cylinder number 2 and 4.
I know coil on plug are prone to be weak on those engines so I go ahead and order 4 new coils which are pretty low cost which is good. Once install on the car I go again on a test drive. car ran really smooth and no check engine light came on. I said fine! I fixed the problem only to discover the day after that the CEL decide to come back on I scan again and this time only get misfire on cyl #2 with fault frequency of 39.
I suspect my injector to be bad but before I decide to remove the intake manifold and spend another 2-300$ in parts. Any way to test my injector with VagCom in order to see if that really is my problem. Also heard the PCV could be a problem but i hardly doubt it would throw a fauly code on just one cylinder.
My 04 1.8t is running rough with the cel on. i scanned it and cyl 1is misfiring. tried changing plugs. seemed to work while idling but as soon as i accelerated it started running rough again.
View 4 Replies