Ford Excursion :: 2000 - Trans Dies And Bogs Down With Any Shift Change After Long Freeway Run
Apr 10, 2014
Tranny died 12000 miles ago and shop rebuilt tranny with new torque converter.
Problem then and now is after long freeway run 60+miles it dies and bogs down with any shift change. If it is placed in 2nd it will bogg down and die. If the tranny auto shifts it also dies. If it cools or just sits it will run again for a while. This does not happen always so it is hard to duplicate it.
Truck is not towing or even loaded most of the time and only once was it loaded when it died, the first rebuild. Truck has 249000 miles, ex v10.
So any clues as to what the shop missed last time and is it worth rebuilding again. Truck is only worth a bit more than the cost of shop time.
View 6 Replies
Advertisement
I have a 2000 6.8L V10 Ex, and I'm currently working through the last thing on my "to fix" list. The truck has 37" tires (Nitto Mud Grapplers), and at freeway speeds the speedometer is off by 10mph. If it reads 60mph, I'm really going about 70mph.
I thought the solution was to order an SCT flash tuner, so I purchased one with tunes from 5startuning:
**1. SCT 7015 - X4 Flash Device with Choice of 5 Star Tuning Custom Tunes - 5 Star Tuning
I choose the correct Revs per mile for my tire (560), but the speedo is STILL 10mph off at 70mph.
No changes that I made to the tire size or axle ratio made any difference. It always read the same amount off. The SCT X4 flash tuner wasnt able to change the speedo on the 2000 Ex's.
[URL] ....
My question is this: If both of those tuners plug into the exact same port, and use the same parameters, why is it my X4 tuner can't change the speedo, yet this other tuner is able to? It doesn't make any sense to me. If the X4 truly cannot change the speedo of certain model years, there should really be a disclaimer about it. Feels like a bit of a rip off since the only reason I purchased it in the first place was to correct my speedo...
View 4 Replies
2000 X V10 4WD... 178K. Truck was not well maintained for most of it's existence. Drained both the TC and Drain pain and replaced the oil filter. Tranny oil looked like crude and a lot of tiny specs of metal - it shimmered in the sun... needless to say - I'm pretty sure it had never been changed.
Now - issues since I've gotten it done... Tranny has been slipping... I figured that I may not have filled it enough and after adding a few quarts, it seems to have stopped. Slipping was initially just when going from a stop.
Now it's having a problem where the engine dies when I shift from one position to another... For instance - from Park to Reverse, the engine RPMs drop as the clutch engages - but they drop from about 900 RPM down to about 500. And 50/50 chance the engine dies. Going from Park to Drive, the same thing but maybe drops to about 700 RPMs. Tried it in 2nd and 1st gear. Has happened in both. I've tried shifting to OD first before going to 2nd to 1st or vice versa and seems to behave better.
Should I flash the ECU and have it relearn the shift points? Did I overfill? Between the TC and Drain Pan - about 16 qts came out. I've been checking the dipstick - no frothing or bubbles. When running and in park - it actually shows low. Seems to drive fine once it's on the road. The engine cutting off when it's put into gear is really unexpected.
View 13 Replies
My TC motor picked today of course with the snow to go bad. Luckily I hobbled to advance right as they were about to close and got one. I laid in the snow and changed it. Needless to say I got soaked beyond belief. Anyways now it changes in and out well but still seems way to loose in the rear. Not sure if something else is malfunctioning or if these things are like that. Right now I don't feel nearly as safe as I did in my expedition and that was without even using 4hi or low just the A4WD. The excursion is sliding everywhere. My tires have great tread but are highway tires so maybe that's the issue. They are Dura Grapplers. I'm going to try throwing some weight in the rear to maybe gain some traction.
View 2 Replies
I have a 2000 X 7.3 diesel with under 100,000 miles. I drive it about 10,000 miles a year, all towing. However it does get used everyday driving a student to the bus, a distance of about 10 blocks. There is an engine block heater which I use all winter but the engine never warms up on the ten block run. I do service the engine twice a year, every six months. What damage am I doing and what can I do to prevent any damage?
View 14 Replies
I have a 2000 Excursion with a 7.3 diesel. I have 245k on the clock. Engine and transmission are original. I have an overheating issue when I am towing and pull a long grade. It's not as bad as it was before but it still happens and I am tired of turning off the AC and putting the heaters on full blast to support cooling when it is 90 plus outside. A list of things that I have done so far.
Newer water pump and thermostat.
New tensioner.
Installed a new trans pan with about 7-8 larger capacity.
Used some magic juju juice to clean out colling system.
Installed a coolant filter. I am on my 5th filter. The first one didn't last 500 miles before getting stopped up.
Switch to Delo ELC.
I recently had the upper hose off and when I looked inside, I didn't see any scale or build up. I also read about some of the trucks of that vintage didn't get a trans cooler. When I looked, I saw a cooler but it doesn't look like it is plumbed through the radiator.
I want to install a large trans cooler. I don't want to replace the radiator just for the sake of replacing it. Also, look at the pic of the water pump with the thermostat sitting in it. Is the thermostat supposed to be resting all the way down? I keep wondering about that.
View 14 Replies
I bought a 2000 Ranger 4x4 3.0L auto today from the neighbor guy sight unseen with a "bad tranny" for $400. I'm very unfamiliar with the Ranger family, but long story short:
When moving the shift lever, the trans doesn't engage. It needs to be engaged from underneath. Do the cables tend to stretch, or break? I can't find any adjustment on it anywhere.
View 5 Replies
I have a 2000 excursion V10. It will die in gear forward or reverse the overdrive light flashes and cel shows code p0720. I have new plugs and COP on all 10 cylinders. I have replaced the differential speed sensor and the sensor on top of the transmission. I have a basic code reader it shows at the time it dies the vehicle speed is 70 mph while the speedometer shows 0. When I unhook the abs module it still has code p0720 but it does not die. I am replacing the abs module?
View 8 Replies
I have a 2000 Ex limited 7.3 4x4 with 196k on it. I bought a new snow plow two years ago and the first season, my transmission went out during a plow job. It had about 175k on the truck and I bought it with 155k with no real knowledge of any work being done to the transmission. So, I had a local transmission shop rebuild the transmission. The owner has done plenty of transmissions for my family in the past with no issues. Once I got the truck back, the reverse was lagging. I didn't recall it being that way, so after month or so, I took it back in to him. It was about 7 seconds to shift to reverse.
He replaced a solenoid and valve I believe. That supposedly fixed the issue and got it down to about 3-4 seconds. I drove it for a month or so then took it back when I was plowing and the reverse went out. He dropped it and went through it. He said the check ball went through the backing plate. He repaired and now I am driving it, but still not happy with the reverse lag and it's out of his warranty period. It's irritating day to day, but when plowing snow, it'll drive you mad! I'm no transmission guy, and not sure why it's all of a sudden different than it was prior to rebuild.
View 4 Replies
I have a 1985 ranger 2.3l efi and it bogs and dies while while driving, it can sit and idle all day long but when you go to drive it, it works great for 3-4 minutes then out of nowhere starts bogging sometimes I can keep it going a little longer but in the end the truck always dies . I know I'm loosing fuel pressure , I hooked a gauge up to it and drive it down the road when the truck died it showed 10 psi , from here I'm lost . It has a new fuel pump in the tank and I can hear the other one running when I click the key on , Also two new fuel filters .
View 3 Replies
2000 Excursion 7.3 unk transmission
Quick run down on the situation. It has been terribly hot here bumping 105 degrees. I was told by a man he could see fluid leaking and it was trans fluid. I checked it and filled it up and got it to the shop.
Next day they said it was not leaking and that it probably overheated. They recommended an after market trans cooler. They put it in and off I went. 60 miles later I got fluid all over the rear of the truck. I filled it up again and got it home. Shop says I need a new trans.
View 9 Replies
My pickup always bogs down going up a grade, seems like its flooding out and it starts running real rough and vibrating bad, I have to let off gas and pull over .
Been to shop several times, no one seems to know what's causing it.
View 11 Replies
OK, so my 2000 FWD 6.8L Ex has 128k actual miles on the odometer w/ a stock 6.8L from a wrecked later model truck with ~115k actual miles on this 2nd engine from what I was told by the PO/2nd owner (I have no reason to doubt him and I verified the history with the original owner). So I'm guessing that the 4R100 is original without having ever been rebuilt.
I've had zero issues with the drivetrain up to this point, this truck has always run like a top and been very reliable. This afternoon in drive time traffic the overdrive light started flashing and at the same time I noticed that the transmission was shifting really hard (snapping into the next gear) and not in a good way. I was in stop and go traffic when it was shifting weird like this. At one point I make it up to 55+ and I noticed that the O/D light had quit flashing and now it was shifting like it normally does. Then back into stop and go driving the O/D light starts flashing again accompanied by the weird hard shifts.
Next thing I'm sitting there with my foot on the brake fully stopped waiting for traffic to start moving through the traffic signal when out of nowhere and no indication of anything being amiss the engine quits and I get dash lights including CHECK ENGINE and THEFT. I cycle the key off and then try to restart it. It took nearly 10 seconds of cranking to get it to start up however once started everything is back to normal and I have NO trouble lights illuminated including no O/D light and it's back to shifting normally. I continue on in stop and go and highway speed driving for the next 15 minutes like nothing ever happened, transmission is shifting like it always has. The truck has been turned off once and restarted since that incident, yet no other indications of any issue. What's going on?? What to check into?
View 14 Replies
I also tried jump starting - get same same result. Engine cranks, turns, and then sounds like it is just about to start up normally but it just dies completely. It seems to want to start but just can accelerate the engine high enough to keep it running. Almost like it's flooded on a carb motor.. 2000 V10..
View 7 Replies
I just got a 2000 accent. The problems is that sometimes when I shift into 2nd and 3rd is notches sometimes. But it does not do it when i shift down. Also if I shift fast it will occur less often as when I shift low. When my friend drove the car it didnt do it for him. So maybe it is how i drive or something. I make sure the clutch is down all the way.
View 7 Replies
I have a 2003 Hyundai Accent that is generating a p0713 code. I have replaced sensor and used SP3 fluid. I noticed if I clear codes everything is fine until it shifts into OD. When codes are cleared the car will not shift into OD until it hit about 60mph. The code is generated and then it shifts fine. I would not worry about it put it will not pass IM with the check engine light on.
View 1 Replies
Simple enough the truck starts then after about 30 seconds it bogs down and dies. I am getting these codes.
705 Transmission Range Sensor Out of Position
708 Transmission Range Sensor Circuit High Input
720 Output Speed Sensor Insufficient Input
743 Torque Converter Clutch Circuit
745 Pressure Control Solenoid Malfunction
1747 Electronic Pressure Control Solenoid A- Short Circuit
Sounds to me like the converter it locked up. What do you think? Its a 5.4L
View 3 Replies
Just changed transmission fluid and filter at 175,000 on my 2000 V-10 and now I have a whinnying sound and shifting that does not feel sure footed. It worked fine before the change. Fluid is synthetic and filter is Ford Motorcraft. Did it just go?
View 14 Replies
I have a 2000 Excursion w/ V10 and I have an issue with the transmission form time to time. some times it does not want to shift out of first. if I pull over and turn it off for a few minutes it will be fine for a while and it doesn't do this all the time. A few nights ago it did this so I pulled over and turned it off and it still did it but then it started shifting on its own just fine till we got on the high way which is started shifting in and out of over drive going around 60-65 MPH. didn't want to go too fast not knowing what it could or would do. it did this for a few miles then it started working fine. next day it did the same thing not wanting to shift out of first then started working fine. drove it around last night and it all worked perfectly. The CEL is on but I get a no communication text from the scanner so that is another thing I need to look in to. I'm guessing it is an electrical issue being when it works it shifts fine and it does not slip at all.
View 14 Replies
It is a 2000 excursion its got codes # 135 155 443 743 755 1747 And overdrive light is flashing really....
View 14 Replies
About three weeks ago driving. My truck would not shift come to find out it was a fuse that blew. Well I pull over and replace the fuse it starts right up I get about a mile from my house and it blows again so I shut off my x and then replaced the fuse. Will not start...
Now I am getting a Pats code 1:6 and my obd2 reader says no link on my x. It used to read it all the time. I am trying to figure out what I can check to fix this problem are there any relays. Oh also my check engine light does not come on when I turn the key but my truck does crank. does this mean there is no power to my ECU. I did replace my ecu and it did not solve the issue.
View 8 Replies
