The 2000 X I have has Warn locking hubs on them. Just to be clear, I'd need to switch them to 'lock' then choose either 4-Hi or 4-Low on the dash in order to engage the transfer case, correct?
View 8 RepliesI just recently purchased a 2000 Excursion and had some questions up in another thread. After doing some diagnosing....I have a couple of questions about the auto locking hubs. The problem I have is that even with the vacuum line disconnected from the knuckle and no vacuum...the hubs won't unlock in auto/2wd. I confirmed that the knuckle and the hubs will hold vacuum when I hooked my vacuum pump up to it and it held vacuum (the fitting should be clear as I heard the hub making some sounds). I'm getting ready to pull the hubs to clean and re-grease them. My question is that being they are still locked....will it be any harder to pull them off the spindle and after disassembling them/cleaning them.....when I re-install them....will they be unlocked by default after putting them back on the spline as they have been pulled apart and reassembled?
View 14 RepliesAnd the vacuum pump was replaced.
View 7 RepliesOn my new to me '03 Excursion (I've owned it for 1.5 weeks now), I'm starting to get through the 1st level of issues (Wandering - fixed, Speedo/ABS issue - still working on that, changing the rear diff fluid this week, hopefully).
Now, I want to look into why the manually locking hubs won't turn. When I brought it up to the Previous Owner, who was about as mechanically inclined as my Golden Retreiver, he said "these are auto locking hubs. I never turned those things before".
They are frozen in the non-locked position, so I have to pray that I never need to actually manually lock them.
Any lucky experience at un-freezing stuck hubs? I've started the liberal application of PB Blaster process.
Last weekend I was cutting wood and put my 2001 F150 into four wheel drive for the first time in a long time. I did it "just in case". Anyway, now my fuel mileage really took a nosedive. Is it possible one of the hubs did not unlock? If so, how can I test? Common problem?? 215,000 and going strong!!!
View 8 Replieslast weekend I was cutting wood and put my 2001 F150 into four wheel drive for the first time in a long time. I did it "just in case". Anyway, now my fuel mileage really took a nosedive. Is it possible one of the hubs did not unlock? If so, how can I test? Common problem?? 215,000 and going strong
View 9 RepliesBack in March while still plowing, my auto locking hubs wouldn't stay engaged. After talking to the local Ford service shop they told me that it was moisture in the vaccum lines and that it had frozen. They told me to manually lock the hubs and bring it in to be repaired when I had time. I made a appointment in the middle of May and finally got it in last week. Now the hubs are seized in the locked position and they will not warranty the work or parts because they say it was caused by the salt from our roads. Does this sound right?
View 5 RepliesI got new auto-locking hubs. The updated ones. As I proceeded to replace them, I pulled out old ones and when driver side came out, there was like 1/2 ounce of water that flowed out from where the auto-locking hub would sit. Strange. I had changed out lines, vacuum pump, vacuum solenoid and reservoir. All new and dry. I blasted both sides down with brake cleaner to clean off old grease, let dry and installed new auto hubs. So far so good. Will test the ESOF feature another time. I was wondering where this water would come from? Other side of wheel hubs are dry.
View 2 RepliesAs my truck stands it has OEM automatic locking hubs with a selector for auto or lock. So, why would some one buy manual locking hubs and cap off the ESOF vacuum line when the OEM ones perform the same function by being auto or locked?
I hope this makes sense because if I felt I wanted to go to manual style locking hubs, I think I could simply cap off the vacuum line and then switch the hub to lock if I wanted 4x4 because the electric switch inside the truck is actually what engages the transfer case and puts the truck into 4x4.
Is this thinking/theory correct or am I missing something here?
My hubs will not lock when put into 4x4. I disconnected all lines from the solenoid to both hubs and tested them for leaks... All good there. I put a gauge on the lines at both hubs one at a time while the other is still connected and get no reading when switched into 4x4. I checked for vacuum right out of the solenoid, and I get 2inHg when switched into 4x.
The vacuum pump kicks on every time I start the truck, even if I just shut it off and re-start right away. There is no delay when switching my ac/heater controls to different settings or vent locations. So I know there is vacuum. How much vacuum I should be getting out of the solenoid to the hubs?
2004 F350 6.0L....
Ok, So, Im 40 miles from home stuck in ice and snow in a hotel.. (my wife works close by- thought it would be safer than driving in the 10 inches of snow we got 3 days in a row) so, I go to pick her up tonight and I engage 4hi.. I hear the click and the light comes on.. but no clunk of the hubs locking.. I drop it in 4 lo.. it shifts in low.. but the hubs are not locking..
I hear a ticking sound as I drive and when I put it in 2wd it goes away. I turn off the truck, turn the wheel hard both ways .. get out and I can physically turn the drive shaft and I hear the ticking in the hubs. If I read correctly when the truck is off these should be locked?
is it possible the vacuum is not releasing? I also get the groaning when I start up of the air diverter.. that im told is operated by vacuum.. so I am guessing I have a vacuum problem??
I just ordered '00 F250 SC 4x4 SWB XLT with the factory standard manual hubs. The hubs show up on the vehicle order confirmation as code "21M MAN LOCKING HUB". I can't find this code in the ordering guides anywhere but kbb.com shows this code as "Manual hubs delete. Required with 213 shift-on-the-fly". I want the manual hubs. I think ##### is incorrect. For my piece of mind, could someone who has also ordered the factory standard manual hubs verify that the code is indeed 21M. And for those who ordered shift-on-the-fly, could you verify that 21M does NOT show up on your order confirmation...
View 8 RepliesI am considering buying a 2001 Ford F250 Super Duty XLT 4x4 V10 engine tomorrow. I am hesitant because I cant get the 4x4 to engage. It goes into 4x4 low and high and the front driveshaft spins but it wont engage the wheels. One side locking hub locks but the other side the locking hub is cracked off and so I there is no way to turn to lock that side. I will of course replace the Locking Hub ASAP if I buy the rig but my question here is, if one side is locked should one side of the front axle spin, meaning if only one side Locking Hub is locked should that wheel turn and the other not? Both are not turning but as I said the driveshaft is spinning.
I don't know if both sides need to be locked in order for the front wheels to engage while in 4x4 high or low. Or if one side should engage if only one side is locked; the wheel that's locked of course..
2001 Ford F250 XLT Super Duty 4x4
V10 engine...
My 2009 F-350 4x4 has a front wheel option of Auto or Lock ; I think I understand the Auto option but under what circumstances would I lock the hubs and is it safe to leave them in the Lock mode when traveling on the highway?
View 5 RepliesI have a 2004 Hyundai Accent. The factory alarm goes off intermittently and the central locking engages at times without warning.
I took it to an Auto Electrician who checked it over but couldn't work out the problem. So i took it to the dealer who said it was most likely the bonnet sensor. I wasn't convinced but they went ahead and charged $150 to diagnose and adjust the sensor and said everything would be fine.
Within one day of being 'fixed' the problem has reappeared. I am getting sick of disconnecting a battery terminal every night....
I drove my pickup on mostly dry pavement the other day with it in 4WD and the hubs locked. I got a bit of shimmy/vibration which quit after about a mile. When I got back on ice, the 4WD wasn't working. I assumed the transfer case or locking hubs had failed. Today I got it up on jack stands, put it in 4WD, and locked the hubs. Everything seems fine. What might have happened when I couldn't get 4WD to function.
View 2 RepliesI know this is going to sounds lame, my wife can't turn them, they have cover over it that has to be unscrewed to get at 'em. It would be nice to shift in and out "on the fly" as weather condition change.
Is it a difficult change?
I took apart, cleaned and lubed my hubs. My question is: how does the vacuum make the gears work?
Does the vacuum force (suck) the nylon assembly to push the outer gear towards the center of the truck, sliding on the inner gear thus engaging the teeth so that the axle shaft turns the hub?
When the vacuum is gone, does spring pressure pushes the outer gear away from the center of the truck thus disengaging the teeth from the inner gear and allowing the hub to free wheel?
Is this vacuum source constant during 4wd and not present during 2wd or do I not understand how the system works? I have read about a “vacuum pulse” that locks the hubs and another pulse that unlocks the hubs and this confuses me.
BTW, I like the way the Auto lock works. I had a set of Warn Auto Lock hubs on my 78 CJ. They worked on the principle of a set of roller bearings that would lock (pinch) when there was torque coming from the drive shaft. There was no vacuum involved at all. The down side was that when you coasted, the front hubs would be in two wheel drive and so you would not get the engine braking on all 4 wheels. These ESOF seem to have solved this problem.
Oh, I should probably tell you that I just purchased my 04 F250 SuperDuty 4x4 with the 6.0 diesel, just had it a week. It has been 18 years since I owned a 4x4. Before this I owned an 87 F250 2wd with the 6.9 diesel.
My F350 4x4 won't go into 4 wheel drive unless I get out and take them out of auto and put them in locked position and when I have it in lock mode it seams to work like it's in auto mode, when I put the switch on the dash in 2wd, it seams like it's only driving the back wheels....
View 14 RepliesToday was the first time I have locked my wheel hubs in and used 4 wheel drive. However when I did all this i noticed that when I turn there is a growling sound but only when turning. It does not make the sound when unlocked and in 2 wheel drive.
View 4 RepliesI've noticed my front axles are rotating all the time even when the hubs are in auto and supposed to be unlocked when in 2wd. Is there a rebuild kit for these so they will unlock the axles or do I need to buy new locking hubs?
View 14 Replies