Ford Excursion :: 2000 - Front A/C Blower Not Working
Oct 29, 2013
I have a 2000 EX and my front A/C blower wet the bed yesterday. I have checked the fuses under the dash and under the hood. I removed the blower motor and supplied 12vdc directly to it. Works like a champ. I metered the harness connector with the ignition on and the fan speed switch at all speeds, I get a range of 8.1 to 8.9vdc. I metered the fuse terminals as well and get a steady 13.2vdc. Before I rip the dash apart, what is the most common to fail the Blower Resistor, Fan Speed Switch, or Blower Motor. Or, do I have a completely different issue?
View 5 Replies
Advertisement
My front ac blower fan is not working. I changed the resistor because seemed to be popular answer for fix but nothing I took blower off and straight wired it and it worked so that should rule out blower motor. Right? Swapped relay 103 and nothing...
View 8 Replies
I'm on my second blower motor and fourth blower motor resistor since purchasing my 2000 Ex approximately 3 months ago. The fan returns after replacing the resistor but ultimately, fails after 2-3 weeks. What can I test, what can I do? The weather is changing quickly here in NOVA and being without a reliable heater is a non-starter for the family vehicle.
View 7 Replies
Put a new bulb in the right front turn signal, still doesn't work (parking light works though).
View 10 Replies
My driver side on my 00 x works for the the front 2 windows but not the rear and no other door switch works the windows ...
View 8 Replies
Ok, I've read about the blower motor resistor, and everyone says you should have HIGH speed on the fan.
2002 Excursion with digital display.
I turn the truck on, then turn on the blower. A small puff of air comes out then shuts off completely. I can hear the direction doors opening when i change between foot and face A/C.
Is this the blower resistor that needs changing?
View 3 Replies
Bought my 2000 X from a guy a week or so ago, and am now fixing all of its little "quirks". A/C blower would only blow on high, diagnosed it as a faulty blower motor resistor and got a new one. Pulled the old one out and the wiring plug that plugs into it is fried!! 3 of the plugs are stuck in it from the resister itself and there is obvious signs of shorting. What my next step should be? Im considering getting a new plug and splicing the wires back into it, but that just ignores the obvious shorting. How to fix the short?
View 3 Replies
Have an 05 Limited Excursion v10 where the front blower motor will cut out randomly. The rear blower will work without issue even when the front is not working. When the front is working (98% of the time) all speeds seem to work and can adjust to all heating/cooling positions. After searching the forum I thought the likely culprit was the blower motor; which I replaced this pass weekend but coming home from work it cut off again, clearly the issue is not resolved. I know the ford resistor are known to be prone to issues but symptoms do not seem to point that direction. Also it is does not happen with any consistency, happens at idle just as frequently as the expressway. What else to check and how to check before I have to give in and take to dealership...
View 2 Replies
Recently bought a 2003 E350. The front heater/ac blower motor isn't working. I found the control switch melted and bought a new switch. Before installing it, I need to do some diagnostics. I checked the blower with a couple of jumpers ant it turns and blows. I think that leaves the blower motor resistor. Where it is on a 2003 E350? I also need to check the relay. I have a power distribution box at the front left under the hood. Is the relay there? The box is not labeled like my GM products. Which is the blower motor relay? Finally, which fuse controls the blower motor? I read it might be a 40 amp fuse. If so, that might narrow it down.
View 6 Replies
My blower motor in my Jetta recently stopped working. When I turn on the blower it works for 10 seconds or so then slows down and dies. Is this a blower motor or resistor problem?
View 1 Replies
I own a 99 Suburban 1500 5.7. The front blower motor stopped working on all speeds so I replaced the resistor, it still did not work. I then replaced the speed selector switch and it started working fine. Three days later I smelled a slight electrical burning smell and the fan stopped working again. I plan on replacing the switch again to see if that is what went bad. Whats causing this to happen? Maybe the motor is going bad and causing the switch to short?
View 6 Replies
I have a 2000 ex with the 05 front end. My headlight on the right side stopped working I have the high just no low. I replaced it and still no go. I suck at wiring so what to look for..
View 3 Replies
Low beams work fine. When I push the Multi-Function lever on the column forward to activate the high beams, I have no lights at all. When it is in low beam (middle) position, low beams work fine. When I pull back for click to pass, only the low beams are active. No high beam indicator in instrument cluster. I have:
1. Replaced both headlight bulbs
2. Replaced the multi-function switch on the column. Checked test pins on switch (MF) they are hot when in either high beam position or click to pass position
3. checked fuses (interior)
#8 - power on both sides of fuse
#16 (15a) High beam headlamps, instrument cluster. ***NO POWER ON EITHER SIDE***
4. checked fuses (engine compartment)
#10 - power on both sides
#21 - Power on both sides
#23 - power on both sides of fuse
View 14 Replies
Just bought a 2000 Excursion PSD 4X4 last week. So far, I have really enjoyed it. There is just something special about these beasts.
I have had trouble with the liftgate lock not working. I tore into the liftgate and found that the actuator works just fine...the lock mechanism is just a little stubborn. I have soaked it liberally with wd-40. There is a lot of dirt road dust in the liftgate body.
View 3 Replies
Have a 2000 excursion V10. Cruise wasn't working when I bought it. There are no lights on the dash that come on and I changed the switch on master cylinder. What to do. Fuses are good
View 2 Replies
I have a question on my '00 7.3. Cruise control just quit working. From reading the threads/forums I have gotten some ideas, but how about no dash light when turning the key to on? Nothing with the self test also. How can I troubleshoot the switch in the steering wheel? I could also have a bulb out in the cluster, but either way- no cruise function.
View 4 Replies
The water level is up, the heater hose is hot on both sides of the heater hose bypass valve, the MtrCrft thermo is pretty new, but it blows cool air out the vents even after a half hour of driving. It was working great last week and then nothing. I guess you can see the blend door moving if you pop the glove box out?..........haven't tried that.
View 14 Replies
The overhead council temp/compass/ mpg on my 2000 xlt stopped working, who has fixed this already?
View 6 Replies
On my 2000 Ex my overhead console screen does not work. I have searched and found a few F series ones but nothing about the removal of the huge console. Is it pretty much the same process?
View 4 Replies
My rear A/C and heat are not working on my 2000 X. I don't have an owners manual for my truck, so if there's a rear A/C fuse somewhere either under the dash or under the hood?
View 2 Replies
I have a 2000 Ex V10 with 170,000 miles and the passenger side headlight stopped working. I changed out the bulb and when that didn't fix it, I changed out the harness.
The driver side headlight works fine as well as all of the other lights. What to look at next.
View 5 Replies
