Looking for a diagram of the steering column? I am looking to see what is behind the ign tumbler that sends power to the ign switch module. I believe a problem might be there . this is for a 2000 x limited 7.3.
View 1 RepliesI have a squeak that developed in the steering column whenever I turn the wheel. It is as if something lacks lubrication. It does it in all steering positions. I guess next step is to open it up and see if I can get closer to the source so I can hit it with WD40.
View 6 RepliesStarted truck and turned the wheel far to the right and shut the truck off to get better access to the grease zerks. Now the entire column, ignition is locked up tight. I can't turn the key, remove it, anything? Thoughts? I'm stuck
View 14 RepliesLooking for the wiring diagram for the circuits on the steering wheel? For some reason, when I hit my cruise control on button, the horn honks...
View 6 RepliesLooking for a link to the fuel pump wiring for a 2000 V10 Ex? I'm trying to pinpoint my no start issue and want to make sure I don't miss anything. I think it goes from 20 amp fuse under hood to inertia switch to relay under hood to pump? 20 amp fuse has power but at the inertia switch I have no voltage, just approx 35 ohms resistance to ground on both outside wires. Does the inertia switch close a ground or should it have voltage?
View 10 RepliesI am in need of a wiring diagram for a 00 ex with factory auto dimming rear view mirror. It only has 3 wires and I think I have them figured out but would like to make sure before making a pigtail to install a mirror I have that has 6 wires.
View 7 RepliesNeed good diagram of all parts associated with the front suspension and axle components. I mainly need the axle components but looking for a good link or pic of the diagram with labels. I am rocking a 2000 Excursion V10 with 4x4. I have found some that are close but not the exact set up I have.
View 4 RepliesI removed the rear radio controller from the back of the console and installed a power inverter in its place. It fit great and everything went smoothly. I should have known it was too easy... I now have no sound coming out of the rear speakers. I assume there is a way to jump the wires to allow the speakers to work, but I'd need a wiring diagram. Right now I have the controller hooked up and buried in the console, which I guess is fine. It's just annoying.
View 10 RepliesI've got 2 amps/ subs I'm trying to install. I've got a couple of questions. How have you ran your power cable? Is there an opening or access that is pre-existing or did you have to drill an area in the firewall? With the factory head unit, which wire do I need to tap for the turn on wire? Also, just a side note. The second row headrests have been replaced with monitors which I plan on removing. I'm assuming they have some type of power cables already ran for them? Would they have the turn on wire as well? I haven't had time to see how they're wired up yet. If the wires are large enough I may just add a fuse in-line and call it a day. I guess it depends on how they are wired in. But if I can use the pre-existing wires there for either the power or the turn on wire it would make the install a lot easier.
View 14 RepliesWorking on the dang ram 3500... I am needing to add a relay, however, i need to strap the coil of it with a diode to protect the frigging cluster (the new dodges aren't very mod friendly!). My question is, should I add a second diode before the relay to protect the cluster against back emf, or will the one strapped across the relay coil be enough?
Since I am sure you're curious now, the cargo light (light that lights up the bed) gets its power from the gauge cluster of all places. I need to add a relay to the cargo light circuit to drive some other lights, and I am worried the back emf from the relay coil will fry the cluster circuitry.
Looking for a wiring diagram for the interior lights? 2004 EB.
Gotta chase down the problem, no interior lights coming on, switch or gem...
Ive got a 2004 excursion Eddie bauer and I've got the non-towing paddle mirrors with power adjustment, heated, and turn signals. I want to put the 2008 style towing mirrors on that have power adjustment, heated, turn signals, and have the marker lights but not power fold or power telescope.
How I can wire these new mirrors to my factory wires? I understand that the marker light may have to be separately wired in, but all of the other functions I want to wire in to my existing wires.
I have a 03 for excursion and I am pretty sure i blew the relay for the fog lights today but looked in the glove box and everywhere for the owners manual and cannot find it anywhere in site... Looking for a diagram or can take a picture of where the fog light relay is and post it on here and which fuse or relay it is ?
View 14 RepliesCurrently I have a license plate camera wired always on connected to a 7inch lilliput monitor infront of my center console on that hump in the floor. The monitor is connected to a 12v plug on the dash. In this configuration, I have to reach down and turn the monitor on whenever I want to reverse and im hoping I can make it turn on whenever I go into reverse. Right now, if I turn it on then turn the truck off, the monitor stays on with a bright blue no signal screen which forces me to turn the monitor on, then off, every time I reverse if I want to use it.
Any way to make the monitor turn on/off when I put my Ex in reverse?
My park lamp circuit is dead. I have tested with a multi-meter and there IS power at the fuse. However, no power at the plug. I have pulled the bumper and found the plug for both the rear taillights (the park lamp circuit WORKS in the taillights) and the trailer wires. Confirmed it is dead there as well.
Both bundles go into the frame rail at the fuel tank, but I not sure which is which where it comes out at the firewall. A web search did not reveal a diagram and the Ford repair CD I have does not list Excursion diagrams.
Need a wiring diagram that will show me how the rear window defroster circuit works in my Excursion. I have the EATC, which may or may not be related... not sure. So the diagram would probably need top be from 2002-2005. Obviously I ask because mine is not working (and neither are the mirror heaters since they are activated by the same switch - I think???). I've checked fuses to no avail...
Mine has never worked since I got this Excursion put together last year. I have read some previous threads that mention two different rear hatch glass defroster grids, one being a higher output grid (and different resistance?) than the other. Is there a chance my system is looking for the higher ohm grid, but my window grid is the lower ohm unit and therefore not activating the timer? I only ask this because my electrical system is M/Y 2002, but my back hatch is from a 2000 M/Y.
Also, I get no indicator light when the switch is depressed. I have tried 3 different switches just because I had extras... no luck.
I think my steering column bearing is bad up at the top end. I got the steering wheel off and the coil spring wire thing without too much drama, but my Haynes manual stops there, it doesn't tell how to go any deeper into column. How to proceed? Almost forgot, this is a '97 F150....
View 2 RepliesSteering column recall ? The ford sites don't have much info yet. What is involved steering column replacement ? Computer reprogramming to sove the issue of the steering ?
View 1 RepliesMy `88 Aerostar needs a replacement steering column. I believe everything can be swapped over therefore color of steering wheel does not matter. Cruise control buttons and tilt are a must. I would like to find one that is tight(er) and not sloppy floppy like mine is slowly becoming (143k miles).
View 1 Replies2000 Ford Expedition, XLT, 4WD, V8, 5.4 Liter. Had heater core bypassed, changed, am re-assembling, but need diagram for where all hoses connect on block, etc.
View 1 RepliesI recently bought a 1993 Aerostar. When I go to drive it after it rains as soon as I turn the steering wheel a good deal of water comes from the bottom of steering column right into my lap! Why this happens and what I can do to fix it?
View 2 Replies