Ford Excursion :: 2000 - 4WD Won't Engage?
Feb 9, 2016
I have a 2000 excursion v10 with 66k miles on it. This past weekend i went to engage my 4wd and it would not work. the light on the dash is on and i think i heard a click but no luck. A buddy told me to tap the transfer case motor with a hammer but am a little skeptical. another friend told me to check the vacuum switch with the vent/ defroster but i am not sure that holds true with my yr/model (i did a test where i left the vent setting on face/feet then turned on the 4wd. the airflow seemed to remain as set). About a year ago i removed, regreased and repacked my front hubs.
View 10 Replies
Advertisement
I have a 2000 Excursion 7.3 4x4 with 237k miles on the original 4R100. Yesterday afternoon I went to back out of a parking space and the truck wouldn't move. When I put it in R, the transmission will engage and upon pressing the gas pedal it acts like it wants to move but will not budge. It rolls forward with no issue or noise. It will not roll backwards at all - not in neutral and not in reverse. The transmission shifts fine but with some hesitation to engage each gear. I have noticed some slippage but nothing crazy.
I 1st thought something might be wrong with the rear end but after some research I think it might be the transmission.
View 12 Replies
I am a new manual 4wd system. i have a 02 excursion. i have tried to turn my hubs but they don't seem to move. i am unsure how to engage the system.
Should I put the hubs in the lock then put it in 4 wheels hi or low or the other way ....
Now from reading some of the forums it may sound like my locking hubs may be frozen and need replacing ....
Any good set of locking hubs and can i rebuild my sock ones for spares. its there a step by step on how to replace the locking hubs ....
View 6 Replies
The Transfer case motor works fine changing from 2H to 4H and back to 2H. Verified the drive shaft is locked in 4wd. Drive shaft is free when switching back to 2H. Hubs work fine and no problems on the vacuum side. Garage is 50+ degrees.
Very occasionally I can get into 4 Lo. (Neutral - complete stop - brake pedal depressed). My main question is could the Transfer case motor be bad if it works in and out of 4H with no problem? I have not seen any answer to this question from my searching. Also, could the dash switch be going? Last summer this started and now seems to be getting worse. This weekend I could only get into 4L one time. Where to start checking (motor on transfer case or dash switch or other)?
I have tried rolling slowly, backing up etc... Problem is I can easily hear the motor work when going to 4H and going to 4Lo (when it is working) most times when it is switched to 4Lo, there is complete silence like there is no power to the motor at all. Tapping the motor does not work. I pulled the electrical connectors off the motor and all pins on both plugs look clean and new.
Thought to first check the dash switch but not sure how to check it. The motor could be also a problem? Is there a way to remove the motor and check it?
I want to get this fixed by the spring since I use 4Lo every weekend when launching the boat. (Never has been deep enough in the water to get close to the Transfer case)..
View 3 Replies
Looking at another Ex but the owner says the transfer case does not engage. Says it can be locked into 4X4 by crawling under it and engaging it manually by removing a motor [Servo motor ?] Does this mean I would need a new transfer case or just the servo motor ? I know mine did the same thing last winter. It would go into 4X4 and then pop out.
View 10 Replies
I had to make a few trips up and down the snow covered driveway. I moved the dash switch to 4wd high for each trip and then back to 2wd when I was turning around at each end. On my final trip back, I got stuck while turning around in 2wd. I tried switching to 4wd high and low but could not get either to engage with rocking back and forth.
The dash light did not come on and only the rear right wheel was spinning. Shifting to park or neutral and turning the switch to 4wd did not change the results. When I finally got myself unstuck, the 4wd still wouldn't engage when driving in a straight line.
What could have broke or stopped working? Bad vacuum line? Bad fuse? Could I have still initiated 4wd by manually locking the hubs? If so, is the process with the dash switch still the same even when manually locking the hubs?
View 14 Replies
I have a 2005 Excursion with 6.0 PSD just turned 80,000 miles. About a year ago, the vacuum hubs on the ESOF system became intermittent, so I changed then out with WARN manual hubs, which proved to be 100% reliable. Today, I got in the truck to move it, and engaged 4x4 High, as it had snowed last night and my inclined driveway was slippery. The hubs are locked, I get a lighted "4x4" idiot light on the dash, but the front wheels are not providing any drive power at all. I can hear the transfer case shift motor moving the gears, and if I select Low Range, the transfer case does change over to Low, but still no drive coming from the front wheels. I'm under the impression that the only things left to fail would be for the propeller shaft to be lying on the ground (it's not), the differential is not working, or something is wrong with the spindle shafts. Nothing has happened to the truck, and I have not heard any strange noises. I parked it 3 days ago, and everything, including four wheel drive, worked fine at that time. What may be going on here?
View 8 Replies
And the vacuum pump was replaced.
View 7 Replies
I bought a 2001 Excursion Ltd 4 years ago. A previous owner put Warn Premium hubs on it, which I would have eventually done myself.
I got stuck a couple of weeks ago and tried to use my 4wd. Nothing.
A friend suggested I replace the Transfer Case Motor as it can go out if you don't use it. I got that done today but I still don't have 4wd.
I can hear the transfer case shift and see the drive shaft spinning, but the front tires don't spin.
I thought it was the PVH solenoid, but discovered the Warn locking hubs don't use the vacuum and it has been disconnected/plugged.
View 14 Replies
Just a little background, my Ex is a 2000 V10 4x4 with 217,000 miles. I've owned it for a little under a year. Very clean truck, and well maintained by previous owner. Now the issue. Starting about a month after I bought it, it would occasionally hesitate to engage drive from park. I checked fluid and it was full and clean. I had a buddy recommended that I check for chafed wires in the steering column which I did and found nothing. It seemed to get better for a while but now it's back. It's doing it more than half the time I put it in drive and sometimes takes 10-15 seconds to engage. So am I probably looking at a new trans? Or, is there anything that can be done to save the old trans?
View 1 Replies
Monday I started my truck after leaving it in the garage while on a 8 day vacation. Shifting into reverse led to almost no movement at all. After a few seconds, I shifted back into park and then reverse again and got a solid reverse right away. I may have noticed sluggish shifting into reverse previously, but not this noticeable. What could be the culprit?
2001 Excursion 7.3 4x4 .....
View 14 Replies
Everything I've seen in the forum refers to alarms activating and how to turn them off, my problem is the opposite. Last year I performed a simple injector cup procedure on my 2000 7.3 Excursion which took about 3 months, during which time I had my batteries removed. When I finally buttoned everything back up I noticed that my alarm does the "chirp", but that I can leave a window rolled down and open any door without it going off. How to get this to reset? I can hit the panic button and get the alarm, but as a security feature it's not working.
View 6 Replies
My reverse lights and back up alarm will not engage unless i hold up on the shifter while in reverse the only thing i found was a adjuster for the indicator....
View 14 Replies
My Excursion is having an issue with the 4x4 system. The. 4x4 selector switch on dash lights up properly for 4x4, but the auto hubs don't actually engage. The hubs will lock only if I manually lock the hubs. I can hear relay click, so I don't think its electrical. The hubs had new o rings installed when I did front ball joints a few thousand miles ago, and the 4x4 worked fine up until today.
View 5 Replies
I have a problem with my AC that is driving me mad. The compressor won't always engage, especially when accelerating. I browsed the forums and came upon this link; SpringerPop's Compressor Clutch Air Gap , very useful. With the AC on, when the compressor didn't engage, I just hit the clutch plate with a wood pole and the compressor immediately turned on.
So its definitely not pressure related and as far as I know, the relay and wiring are working or else it wouldn't even turn on. It works well for a few minutes (very well) and then it just stops working. Anyway, I read the instructions on that page. The thing is... when I put the keys in ON and turn the AC on... the clutch still doesn't engage, making it impossible for me to get the plate out to get the shim out.
Model: Ford Explorer 2000 SOHC....
View 8 Replies
When putting vehicle into park, every so often it will barely enage or not at all. Can hear a clanking noise when rolling back or forward. Trans position sensor?
View 1 Replies
2000 F 150, 4.2 v6, M5OD-2 Manual Transmission, LX, reg cab .. Cruise Control passed all static and dynamic self test. All fuses inside and under hood checked good and still cruse control will not engage. All other functions work: brake lights, turn signals, etc. Green cruise light is operational, checked pin #10 on wiring harness at servo,amplifier unit under hood and have good ground. The Cruise ON button will not turn on cruise control system and will not light green cruse light.
View 4 Replies
I have a 2000 F-150 XLT Supercab 5.4 4x4 with the dash shifter. My front axle won't engage when shifting into 4x4. A few months ago the vacuum solenoids were replaced and they sound as though they are functioning properly. The diaphragm isn't moving the lever thing and i can't get the lever to move with a screwdriver either.
I know it has worked the past two weekends. Two weeks ago it was in a significant amount of mud and possibly submerged at times. I power washed everything pretty good immediately afterwords though and it has worked in between then and now. What could be going on?
View 11 Replies
I bought a 2000 Ranger 4x4 3.0L auto today from the neighbor guy sight unseen with a "bad tranny" for $400. I'm very unfamiliar with the Ranger family, but long story short:
When moving the shift lever, the trans doesn't engage. It needs to be engaged from underneath. Do the cables tend to stretch, or break? I can't find any adjustment on it anywhere.
View 5 Replies
I have a 2000 f250, 5.4l triton v8 that cranks like crazy, but won't start. When I spray a little starter fluid in it it will run until the spray wears off. Brand new battery and full gas tank. it does have check engine light on dash, probably from the o2 sensor as the exhaust has almost completely rusted out. Also on a side note the cruise control will not engage.
View 6 Replies
Our 2000 blazer LT 4.3L 4 door 4wd has 190,000 km (about 115,000 miles). 3 Button dash control. Transmission was rebuilt at 100,000 miles (main troque converter spline was shot). The 4 wd will not engage in either hi or lo.
Whether moving or not, press 4 wd lo, light stays on. but nothing happens. I cannot hear the transfer case engaging.
Had a previous problem, (withflashing light): found the vacuum hose under battery case was worn through.
I do have a service engine light on the dash. This may be unrelated, because 4wd stopped working long before service engine light came on. I have changed the Oxygen sensor, but no reset the fault yet. Where to start.
View 13 Replies
