Ford Escape / Hybrid :: Trans Acts Like Low Fluid At Low RPM Situation
Jul 6, 2014
I just did a Sable 3.0 engine swap on my 01 Escape auto 4WD with 112K miles. Prior engine spun several lower end bearings. New motor runs fine. Prior to swap, trans operated fine. Didn't have any of the apparently common 2-3 flare or OD shudder problems. Car was dealer maintained and fluid looked fine - didn't look or smell burned.
Now, after the engine swap, from a stop or at low RPM situations like around a slow corner, the trans seems starved. Have to rev the engine a bit to get the pressure up, car jerks into gear and then trans operates fine. Shifts through all gears fine and goes into and out of OD fine. This happens from a stop when trying to shift into either Fwd or Rev. Feels like the trans is low on fluid, but it's not.
I drained the trans prior to doing the swap and refilled with Mercon, not Mercon V.
No engine codes. Kept my OBDII reader on while driving to see if it threw any temp codes. Still no codes.
I'm sure that the trans was reinstalled correctly. I'm sure the TC didn't cram the pump.
If I recall, there are only four trans sensors and I'm sure I hooked them up correctly.
I'd like to like this car but it's getting pretty hard. Since I bought it a month ago, I've been under it more than I've been in it.
View 14 Replies
Advertisement
Doing trans fluid change on the 2009 -2012? Is it the same as myCD4E drain 4 refill? I know its a different fluid probably buy from Ford.
View 1 Replies
Original owner 2003 XLT, 3.0, 58K. When in drive and stopped at a light it decelerates and wants to bottom out. No stutter or sputter. Just "catches" for a moment and acts like it going to die and it corrects itself. Can happen up to two times at a long light. It's very scary so I put in park until the light changes. Took it to a shop yesterday and he cleaned the throttle. It had a lot of black stuff that the spray cleaned out and hoped that was the problem as he said it was sticking some. Drive it home, put it in drive, sat in the driveway simulating a long stop light and it did it again.
No CEL. Up to date on all recall notices. Had fuel pump, fuel filter, two coils all spark plugs replaced in January. Yesterday cleaned the MAF and IAC.
On my way to work yesterday, I got on the interstate and it seemed almost like it was missing. I immediately took the next exit and that's when I had the IAC cleaned and I cleaned the MAF. The mechanic did a quick scan and didn't see anything. He did mention it was running rich but otherwise wasn't sure what the problem is. I forgot to ask what scanner he used but can find out later this morning.
It seems worse when cold. Also, I am female and can follow directions like how to remove and clean the MAF and get correct cleaner for it but not much beyond that. I need to know what else may need to be checked. Also added some Lucas fuel injector cleaner a couple of weeks ago.
View 14 Replies
So I am changing my transmission fluid tomorrow and was wondering a few things.
1. I noticed some people pull off the transmission hose to the inlet and keep draining that until its clear. For a drain and fill do you do it like that or just pull the plug and refill?
2. When youre filling it back up you just measure how much you taken out and then fill the rest by the dipstick? Anything else i should know?
3. Since I havent changed my transmission fluid in 60,000 miles. I wanted to do a drain and fill. I was thinking I needed to drain and fill it 3 time to catch up to maintenance. How often would you do it to get it clear? Drain and fill then drive it for a week then drain and fill? Or do it all in one day?
View 4 Replies
Along with a high idle problem that's driving me a little bonkers on my 2002 3.0 V6 Escape, I've noticed that the tranny constantly hunts up and down a little when I'm running about 55-60 mph. Today I got a code P1120. Makes me wonder about the TPS... I replaced it during routine maintenance about a year ago with a unit from carquest, so I don't have the original to replace it with for troubleshooting. Will a TPS also cause a high idle, or are those 2 issues typically not related?
View 11 Replies
I own a 2002 Escape, 4WD 4cly manual trans. A couple of days ago, when I left work I stopped at a stop light. I shifted out of gear while I waited for the light to change like I always do. When I went to shift back into gear, I couldn't. I found that if I turned the key off, with the clutch disengaged, I could shift into gear without a problem, start the car up and drive away.
Since the first time this has happened, it has happened a few more times, always when stopped, once or twice while slowing down to stop (low RPMs). Besides all that, the car shifts fine while driving.
View 1 Replies
My wife has a 02 Ford Escape XLS with a I4/manual trans, she has been saying it has been making weird grinding noises for a while but has not been able to replicate it for me to hear. Today it locked in gear and stalled, she can depress the clutch and start it, but can't take off in whatever "gear it thinks it's in" and it'll stall. To quote her.
So odds are the clutch or trans is toast, I'm more of a full size truck guy when it comes to doing work, what to look at? She's getting it towed and I have enough tools to do the job just not a ton of time this second to do the research, When I know more I'll add it.
View 4 Replies
2002 Escape XLS 2.0L 4-cyl 5MT FWD. Slipping Clutch.
I've read here n there that the Escape clutch is a poor design & others have reported that a clutch repair doesn't solve their shuddering problem. After putting off the job for a while, I'd like to replace the clutch.
Here's a topic from here : Manual Transmission shudder / fill & drain access?
View 2 Replies
My 2010 2.5L FWD Escape has oil on the steering boot and has run down on crossmember (?) It is equipped with Electric Power Steering. This appears to be coming from the rack and pinion but does it have fluid in it? How can you add if it does. I have 96,000 miles on the vehicle and except for a drivers door actuator and scratched drivers glass, this is only problem.
View 5 Replies
Having issues with transmission fluid spewing out the dipstick hole? Truck is an 04 Escape and has worked great until I had a rear manifold leaking. I took the truck to our mechanic and he replaced the rear manifold cat converter. He broke 3 of the 4 bolts so he told me he had to roll the engine forward to gain access to tap out the broken bolts. Im sure he took the throttle body and intake off for more room. I Got the truck back and noticed transmission fluid all over my driveway the next day. I contacted the mechanic and he states it was nothing he did and cannot figure why this is happening. Basically told me to fly a kite!
View 14 Replies
So I put in new clutch yesterday. Reverse works, granny works, 3,4,5 work. ZF6 manual. But when I try to go 1st or 2nd. Its as if the truck is in neutral....what should I be looking for. I bought the truck having only knowing the clutch was completely shot, was not told about this 1&2 gear issue....
Do I need to pull the trans out again... or is there something I can see or adjust, because from what i can see where the shifter connects there is no adjustments. Is it probably a gear selector fork...or connection that took a crap. when moving in granny gear i did not hear any irregular noises....
View 2 Replies
I have a 1997 Ford F-150 XLT 4x4 with the 4.6W and a 4R70W trans. For the past year is has been leaking trans fluid and has slowly got worse and worse. At first the truck would only leak at high speeds (when driving on the interstate for extended periods of time) and now It has gotten to the point where I am adding close to a quart of fluid a week. ( roughly about a quart every 300 miles!). I thought that it was the pan gasket leaking at first, so I flushed the trans fluid (dropped the pan and drained the TC and put on a new filter) put a new gasket on and torqued it all down and added some new Valvoline max life fluid. The first trip in the truck I noticed a puddle of fluid under the truck again.
The pan looked like it could have been a little warped, so I ordered a new pan and a new FoMoCo gasket (the one the came with the new filter was the cheap felt type). I thought I for sure had fixed the truck this time, but I drove it and once again it was still leaking. I checked all that I could before replacing the pan and gasket. I checked the trans cooler lines and fittings (no leaks) I pulled the inspection plug and it was dry (so I ruled out the front pump or TC leaking). The whole underside of the truck is covered with fluid so it is hard to pin point the leak, but most of the fluid drips down on the transmission cross member.
View 3 Replies
Background: No A/C. Identified Clutch had completely failed. I replaced the clutch.
Status: I turned on the A/C and I saw the clutch come on...it was on for maybe 60s. During that time, the vents started to get cold! After 60s it never came on again.
Troubleshooting: I have refrigeration gauges but not much idea how to read the result. I hooked them up and noted about 350psi for the HP side, and about 100psi for the LP side. I think this tells me I should have enough charge in the system to cycle the compressor.
At this point I don't want to start random troubleshooting as I don't want to touch the refrigerant loop more than necessary. A few questions:
1) The HPCO switch, I was reading that it's mounted on a Shrader valve. Is this the case? I'd like to remove it and test at which point it switches. I have not tried bypassing it.
2) Do our vehicles have a temperature sensor near the evaporator? If so, whereabouts is it located?
View 10 Replies
My 2006 Escape Hybrid with <3500 miles on it had the ABS and 4X4 lights light today when I am 60 miles from home. I had this happen a few years ago, and I replaced a cracked tone ring, driving it to the dealer, who was only 5 miles away. My question is, is it safe to drive home and take it to my dealer who is 60 miles away, or should I have it towed?
The vehicle runs, in fact, the ABS and 4x4 light went out - in fact, I think I saw an indicator message that said 4x4 restored, but I am not sure, it appeared and then was replaced by X miles to empty. I would prefer to go home and take it to the dealer I purchased it from, but I don't want to drive in a car where the brakes may not work. I've read differing accounts on the internet and I can't figure if this is a "service soon" meaning I can make the trip home, or if it will strand me or worse if the brakes will fail on the trip home.
View 14 Replies
I just bought a 2010 Escape XLT 4 cyl. The mpg is showing to be 16.7, which is really low compared to what it's supposed to be. I bought it off of a car lot and it had been discounted so I'm guessing it was sitting there for a while before it was sold. Do you think that would cause the mpg to be low? I've driven it on the highway and around town. I've had it for 2 days, but it's freaking me out thinking that there is something wrong with it.
View 4 Replies
Get a set of real gauges if you want to do diagnostics. 110 psi on the low side indicates that the system isn't running at the time and that the underhood temp is around 100 F.
View 1 Replies
Ok, so I've got a little of an odd issue. It seems that no matter what I do, the AC is always active. Today I reverse flushed the heater core in my 02 Escape, and verified all hoses were clear. I replaced the thermostat housing (other thread) along with a new thermostat.
But, when I run the car, even with the heat full up and the selector set to the defroster and floor, the ac still blows ICE cold. It seems like it is still engaged no matter what. Winter is coming and I dont want my daughter to freeze (her truck).
View 2 Replies
Had to change the alternator in the 3.0l fwd escape. if some one knows of an easy way to get it out i would love to know. We had to take the manifold cover off right down to the "o" rings as well as what ever we could undo to make a gap between the engine and the fire wall. it took us so long that the repair shop was closed and we had to leave my engine apart overnight with tissue stuffed in the pistons. The one part you know your going to have to get to to fix, and it's almost impossible to get at. It would have been easier to tilt the engine, but we had no hoist, is there an easier way...
View 14 Replies
How can I test to find out if there is water in my fuel tank , fuel lines, etc. The symptoms are obvious, how do I test for sure. In the event that I'm correct, what can I do to get it out of the tank and fuel system.
I suspect that a lower form of life has put water in the gas tank of my 2003 Escape 3.0L . I sent it to a shop, that was a nightmare . They came up with every misfire and etc. Including bad windshield wipers burned out light bulbs .
Trying to sell me new coils plugs , etc etc ... even though I kept telling them that of course its misfiring if there is water in the fuel. Please test for water in the gas .
I finally went and took the car with intake plenum pulled off. Paid them half of R&R for pulling the plenum and I'm back to square one. They did everything but check for water in my gas tank or fuel lines.
View 14 Replies
I only have one key and 2 FOBs for my 2005 Escape, but I do have the key number (4 digits plus a letter). I understand I need more than one to program another myself. Is there an inexpensive way to obtain/program a backup key?
View 9 Replies
My daughters 2010 Escape (V6 - 3.0L motor) had the check engine light come on back in February, while she was away at school. Well, now she is home and I want to fix it. I have tried all the things I can think of and have found on the web, but no success. I pulled the whole Evap canister assembly down and tested the Evap vent solenoid by itself, and it works (opens and closes). Physically can see if cycle when I apply 12v to it. When I reinstalled it I cleaned up the o-rings and lightly greased them up to seal better in case they were leaking by. Before pulling the whole unit down, I checked and with the key on, there is 12v on the plug feeding this solenoid, but I physically wanted to see it move and it looks good.
Next, I pulled the hose feeding the top of the purge valve, located under the hood, to see if I had vacuum leaking when the car was running. I did not, so if I understand the operation correctly, I am good there as well. What else could be causing the car to dump this code??
View 8 Replies
