Ford Escape / Hybrid :: Starts Out In 1st Gear And With Little Feathering Of Throttle Shift Directly To 3rd
Jul 10, 2016
I am working to analyze my Granddaughters 2008 Escape FWD Auto 2.3 L issues with the Transmission. Vehicle has 142K miles with engine oil changes but no maintenance on the Transmission.
Engine was replaced about 9 months ago with a used 2.3 L with 52000 miles. Engine runs fine with no issues and NO Codes. BUT when driving the Escape I find it starts out in 1st gear and with a little feathering of the throttle will shift at 2600-3200 rpm directly to 3rd gear. (Based on known ratios and rpm vs MPH) Also no OD/ 4th gear. OTHER than the shifting issue it runs fine.Reverse works normally.
Summary: NO CODES from OBDII, NO OD lite ON or flashing, NO leaks, "wrench" light is ON solid after 1-2 miles driving, "wrench" light is OFF on restart but turns ON after 1-2 miles driving, Changed ATF - old fluid was slightly dark but looked and smelled OK - Drain plug magnet had slight coating of sludge - no dirt, metal or other solids. Transmission Shifting Lever properly selects Park - Reverse - Neutral - Drive with a quick/Normal change.
View 9 Replies
Advertisement
I own a 2002 Escape, 4WD 4cly manual trans. A couple of days ago, when I left work I stopped at a stop light. I shifted out of gear while I waited for the light to change like I always do. When I went to shift back into gear, I couldn't. I found that if I turned the key off, with the clutch disengaged, I could shift into gear without a problem, start the car up and drive away.
Since the first time this has happened, it has happened a few more times, always when stopped, once or twice while slowing down to stop (low RPMs). Besides all that, the car shifts fine while driving.
View 1 Replies
I just had an exhaust manifold replaced on my F-150. It has the small 8 cyl.. While the manifold was leaking, the truck of course ran like crap.....spitting, sputtering, barfing, etc.
Now that the manifold work has been done, the truck runs pretty well, except for some intermittent increase in throttle (not by me) when cruising at highway speeds. This is comparable to the "feathering" of the throttle that you would do when checking for engine noises.
Hard to explain without feeling dopey, but kind of a mild ruuum, ruuum, ruuum out of nowhere when I'm cruising along. I drive a 5 hr. trip every weekend, and it will do this about every 10-20 minutes.
View 9 Replies
I need to pull my throttle body so I can give it a proper clean, but Haynes says that I shouldn't use a wire brush because that will damage the "special coating" on the bore and butterfly plate. It says just to use a rag and solvent.
The crud on mine looks like it will need more than a rag, so I was thinking about a toothbrush rather than a wire brush - do you reckon that'll be OK?
View 5 Replies
Well, not an escape, it is a mazda tribute. but it is the same thing as an escape. My sister just called. as she is driving down the road, if she lets off the throttle the engine will randomly die. it did it 2 times sunday, once yesterday, and once today, as she was talking to me. It will not die at traffic lights, just as you let off the throttle sometimes. today it did it at 45 mph. When it dies she just pops it in neutral, restarts it, puts it back in drive, and it is fine. No check engine light after restarting. What I should look at when she brings it over this weekend?
View 3 Replies
I have a 2008 xlt with a 3.0. In the little over 2 years I've had it, most notably in the past year, I have replaced the front driver side ABS sensor 8 times. This is getting extremely cost, and outrageous. Every month or so, the ABS light comes on and the ABS starts locking up when I am driving it. Every time it does it, I have to take it back to the shop for diagnostics, at a rate of nearly 300 a pop. As you can see, the bill for this one damn sensor has become outrageous.
Every time, the same fault code comes up. Drivers front ABS sensor. Putting on a new sensor fixes it, every time, but only temporarily. I have had the tone ring replaced just to make sure that wasn't it, and every single time it's always been the sensor itself.
I have tried various brands, including a couple of OEM a pop to make sure it wasn't just lower quality parts, and I have the exact same result every time. I have noticed it seems to do it most notably during extremely wet conditions, or heavy snow, although a couple of the times it started acting up in the heat of summer. I have even attempted cleaning the abs sensor to make sure it wasn't just dirty, to no avail.
As I mentioned, only replacing the sensor makes the issue go away, and when I am driving the abs system engages at random times if I leave the light on for too long without fixing the abs light.
View 8 Replies
2005 Mazda Trib. will not let me shift out of park . It doesn't happen all the time button seems to be sticking . Is it the button or the electrical switch on the brake pedal ? This belongs to a friend of mine and this is the info I'm getting .
View 2 Replies
I have a 2007 Mercury Mariner with a 3.0 Liter V6 engine AWD. The transmission is giving me a problem. No shift into 2nd and 4th. Solenoid or band broken I think. Is the bolt hole pattern to attach the tranny to the engine different between the 3.0 V6 and the 2.3 I4?
View 3 Replies
I just picked up a 2004 ford escape and information is difficult for me to obtain. Person I purchased from had all new suspension installed. Says it needs new transmission.
My indications: Vehicle starts right up dies/stalls with anything above throttle. Major lack of power. Was able to put in Reverse and it moved a bit and same as drive. Smoke from rear of engine. Seems like coolant dumping into exhaust. shake on exhaust you can hear slosh slosh in exhaust.
No engine trouble codes no lights on dash.
Am I looking at a headgasket? This has the 3.0 duratec v6 with the water pump belt driven by the cam on the driver side. Open up the oil cap there is the timing chain. serpentine belt is on passenger side of engine. There is no coolant/water in the engine oil but the coolant is disappearing FAST. no coolant on spark plugs that indicate its in the cylendars.
Was going to check compression but the compression tester I have only threads up to 14mm. to small for the hole. I can probably rent a tester with proper sizes if needed. Fuel pressure at the rail primes to 60 psi and stays there. Stays at 60 psi while running as well.
View 11 Replies
I have had my truck in the local ford shop because the fluid was a little bit burnt smelling, I had a flush done to it and then afterwards I noticed first gear started hesistating and then would go to second, when it warm it doesn't have any issues, shifts normal, but when cold or starting off even with running in the morning before going to work its still does that, I would like to find out before it starts becoming a serious problem....
View 6 Replies
My 2009 Ford Escape shift lever is stuck, not allowing me to shift out of park without using the manual override. However, when I slam my foot to the brake (rather than simply stepping on the brake), the brake switch relay, etc. all engage and I am able to shift out of park. Is this a brake switch relay problem, or is it possible that it has to do with the age of my brakes, etc?
View 3 Replies
2005 Escape 3.0 with 160k miles. Slight miss under cruise, goes away under slight throttle. No service history known about vehicle. Best to replace spark plugs and coils with Motorcraft parts? And the intake gaskets too? Suggestions for correct plugs?
View 14 Replies
We bought a new 2002 Escape 4WD and it has been great. Just clicked 130k. However, yesterday my wife said the car clunked when putting in reverse, and then the OD light started blinking. Shortly after that the Escape would not drive in gear, just a spinning noise. After the car was shut off for a few, it would drive again, but not very far. Fluid is good, and it will only drive for a while. I noticed a broken vacuum line coming from the trans, but could't tell where it went.
View 3 Replies
I have a 2002 3.0 Escape. All running great. I have a question about where engine load/vacuum is sensed for determining shift point? I replaced all of the dry rotted hoses in the vacuum recently when replacing intake upper & lower gaskets. since then, I've noticed the shift points aren't quite the same as before. The tubing I used was slightly smaller that the OEM, but otherwise, everything is plumbed up as before.
When accelerating, the engine does rev a bit more than before, before the tranny moves to the next gear. I can ease up on the throttle just slightly, and it'll shift up. If I'm not accelerating hard, it seems to shift fairly normal. Going up slight grades it doesn't want to shift as soon as it should, but on level ground it shifts fairly normal under light load. Going down grade it shifts quickly, as one would expect. This is why I felt it might be somehow related to engine vacuum.
Is there an sensor somewhere, a restrictor in the vacuum tubing, or a vacuum modulator I might look at? I've double checked the vacuum tubing and found no leaks.
View 6 Replies
Problems with my 2001 F250 4r100 transmission. Transmission will only shift to 2nd gear when throttle is feathered at @2500 rpm. All other gears shift perfectly. This problem is consistent.
View 10 Replies
I recently purchased a 2012 Golf Sportline 2.5 auto. I also currently own a 2006 Jetta and 2008 Rabbit both 2.5 automatics. Both older cars run and drive great with this engine and tranny combination for me. However with the 2012 I really notice a throttle delay when accelerating from a stop and a very early shift into 6th gear when in the gear selector is in drive mode causing engine lugging. Shifts into 6'th at 60 kph doing 1100 RPM.
This I find is very annoying compared to my other two VW's which have better throttle response and shift a little later into 6'th allowing the engine to turn at 1400 RPM allowing for better acceleration without having to kick it down a gear.
I have taken it back to the dealer hoping for a ECM flash update but nothing is available from VW and my vehicle ECM has all other current settings and updates. I ve looked into aftermarket solutions such as the Sprint Booster which allows for a more responsive pedal but based on my other VW's my 2012 should not preform like this.
View 10 Replies
So I am changing my transmission fluid tomorrow and was wondering a few things.
1. I noticed some people pull off the transmission hose to the inlet and keep draining that until its clear. For a drain and fill do you do it like that or just pull the plug and refill?
2. When youre filling it back up you just measure how much you taken out and then fill the rest by the dipstick? Anything else i should know?
3. Since I havent changed my transmission fluid in 60,000 miles. I wanted to do a drain and fill. I was thinking I needed to drain and fill it 3 time to catch up to maintenance. How often would you do it to get it clear? Drain and fill then drive it for a week then drain and fill? Or do it all in one day?
View 4 Replies
I took my car in for the 10,000 mile service on friday. The tech noted that there is an active TSB for the 1.8 TSI engine that addresses an issue with the turbo engaging just before the shift from first to second gear resulting in a non-progressive throttle response. I told him that I didn't seem to really notice that issue, but to go ahead an install the software update anyway. He did. I'm surprised at the difference. The throttle is much more progressive and I feel like I have better control of the throttle. I highly recommend this update. This may also explain why the 2015 Passats with the same engine have a higher MPG rating than the 2014s. If this update prevents the turbo from coming on unnecessarily then that would certainly save on gas.
View 21 Replies
I have a 04 grand caravan 3.8 liter. after filling up with gas & only after filling up i have a prob with the way the van runs. it will start and idle fine but once i shift in to gear and try to drive it starts to buck. if i take my foot off the gas it wants to stall. if i shift in to N or park the RPMs are around 400/500. if i rev the motor in N or park it will smooth out and idle fine and drive fine until the next fill up, then it starts all over again.
View 1 Replies
Background: No A/C. Identified Clutch had completely failed. I replaced the clutch.
Status: I turned on the A/C and I saw the clutch come on...it was on for maybe 60s. During that time, the vents started to get cold! After 60s it never came on again.
Troubleshooting: I have refrigeration gauges but not much idea how to read the result. I hooked them up and noted about 350psi for the HP side, and about 100psi for the LP side. I think this tells me I should have enough charge in the system to cycle the compressor.
At this point I don't want to start random troubleshooting as I don't want to touch the refrigerant loop more than necessary. A few questions:
1) The HPCO switch, I was reading that it's mounted on a Shrader valve. Is this the case? I'd like to remove it and test at which point it switches. I have not tried bypassing it.
2) Do our vehicles have a temperature sensor near the evaporator? If so, whereabouts is it located?
View 10 Replies
My 2006 Escape Hybrid with <3500 miles on it had the ABS and 4X4 lights light today when I am 60 miles from home. I had this happen a few years ago, and I replaced a cracked tone ring, driving it to the dealer, who was only 5 miles away. My question is, is it safe to drive home and take it to my dealer who is 60 miles away, or should I have it towed?
The vehicle runs, in fact, the ABS and 4x4 light went out - in fact, I think I saw an indicator message that said 4x4 restored, but I am not sure, it appeared and then was replaced by X miles to empty. I would prefer to go home and take it to the dealer I purchased it from, but I don't want to drive in a car where the brakes may not work. I've read differing accounts on the internet and I can't figure if this is a "service soon" meaning I can make the trip home, or if it will strand me or worse if the brakes will fail on the trip home.
View 14 Replies
