Ford Escape / Hybrid :: Parking Brake / ABS And Traction Control Lights All Came On At Same Time
Nov 2, 2015
So a little while ago I had my parking brake, ABS, and traction control lights all come on at the same time. There was no change in performance, but they have been on ever since. I looked in to it online and a bunch of people said this was a common problem with damaged tone rings, so I checked them out, but they were fine (as far as I could tell anyway). So I scanned the vehicle using a buddy of mine's Snap On scanner, and it came up with the following code:
B1342 Faulty Control Module
We tried to check the fault code through Mitchell OnDemand but it said that this code was for a faulty Parking Assist Module. I don't have any kind of Parking Assist system on this vehicle however. I looked around a little more and this seems to be a pretty generic code for brake system faults with Fords. Also, if the control module for the ABS is the same one that handles traction control?
View 3 Replies
Advertisement
I just bought a 2008 Mercury Mariner about a month ago. A couple of times the Traction Control light came on from when I started it, until I turned it off (5-30 minutes.) Then it didn't come on for days. What the problem could be??
View 1 Replies
I have a 2011 Escape. When I punch in the entry 5 digit code on the door post, I hear a small "click" and the parking lights come on. The door locks, however, do not operate. When I use the key fob the locks do work. What the problem is?
View 4 Replies
The parking brake lever on my '05 Escape will not budge, is there a simple solution to this problem or do I most likely need the whole cable assembly replaced? Is there any particular spot on the cable that's most susceptible to seizing from rust that I could soak with penetrating oil to free it up? I know the inner cable comes out of the coiled metal, conduit-like outer part and is exposed where it attaches to the rear brakes. Is this most likely the spot that's causing the problem?
View 8 Replies
we have a 07 Escape that the brake lights stay on even with the ignition key off. I changed the brake switch twice. Thinking maybe the first may be faulty from the factory. I'm stuck on what the problem could be
View 8 Replies
Evertime I turn left the brake light, traction control and stability control lights come on and the car starts dinging. Mechanic says it could be front wheel bearings because they are tied to the ABS system??? But I have been seeing alot about wheel speed sensors?
Second, everytime I brake suddenly, a cloud of smoke comes from the front end and there is a burning oil smell. The oil is fine and no leaks. Again mechanic says it could be a cracked CV boot throwing grease?
Lastly everytime I put in reverse or when I lightly put pressure on the brakes when driving I get this noise like a humming (errrrrrr) noise. Its not the grinding/squealing noise you would get when brake pads needs replaced. I only have 60k miles on this.
View 30 Replies
My college son's 2014 Charger V6 has developed three issues since he purchased it used in late May. The cruise control has stopped working and the anti lock brake and traction control lights are constantly on. Any possible cause?
View 15 Replies
I recently purchased a 2008 ford escape, v6, 2wd. When I bought it, I noticed the ABS light was on, and I got an appointment scheduled to get it fixed, but they couldn't get it looked at for 2 weeks out. Needing a vehicle to drive to and from work, I agreed to schedule the appointment, as I test drove it with the light on with no issues.
Well, after putting about 200 miles on it over the weekend, there are now noticeable issues. First off, the parking brake light decided to come on intermittently, and now it comes on and off spiradicly. Secondly, when I drive the car now, I can hear a clunking noise, followed by the traction control light blinking (It was on constant before), and loss of power. I ended up pinpointing that to being the brakes engaging while the car was driving (I noticed when I stopped, the rotors were really hot. I threw a tiny bit of snow on them and they smoked really bad.
I removed the tires in the front, and checked the tone rings, they both appear to have been replaced recently as they are still shiny as if they were brand new. I also took the ABS sensors out, and wiped them down, they also appear to be new (Although the bolts that hold them on clearly aren't new). I don't have access to a high-level scan tool to get it looked at, and I refuse to drive it anymore to take it to a shop just to have it looked at, what else could be causing the issues? It's highly possible that one of the ABS sensors is bad, but how do I go about checking it without just replacing it? Can I use a voltmeter or something to check it to see if it's getting the correct voltage?
I am not sure how the abs system works, but I know that the traction control light is on because the abs light is on, as they both have the same systems they use, but would that also cause the parking brake light to come on, too ? It originally wasn't on, but just started doing it recently. I checked the fluid level, and it's more than within range. This is my daily driver, and obviously I can't go two weeks without a vehicle, and that's the soonest I can get it into a shop...
View 6 Replies
2010 Prius 98,000 miles - No Accidents
I was driving on the freeway cruising about 65-70mph.. Not using the brake at all. All the sudden the car starts beeping loudly with the Brake light going off, traction control light going off, and the ((!)) light as well. So I wanted to pull over to the side and realized my brakes were not working . It was the same as if you're trying to brake the car when the car is turned off. I slowly pulled off the freeway. Tried to reset the ECU, battery, everything, thinking at the traction control is just going crazy.
View 19 Replies
My 2012 F250 6.7 once again (third time in 2k miles) got stuck in park with no brake lights or traction control. I found that removing the shroud from the steering wheel allowed me to manually activate the solenoid and get into gear but could only drive in manual shift mode.
Something is causing the brake switch fuse to blow. When I replace the fuse all is well for maybe 1k miles then it happens again! After the second time I replaced the brake switch thinking it was the cause but no deal. It happened a third time. The dealer who fixed it the first time could not find the cause.
This is frustrating and downright dangerous! What in the circuit could be causing the short?
View 14 Replies
I had not driven the Prius in a few weeks, and even then, that was for less than five miles, and had the low tire pressure indicator come on late last week when the temperatures cooled down, which I fully expected given my opportunities with the Toyota Dealer properly inflating tires. We were away for another week and returned today and I decided to check the tires and add air, and in addition to the tire pressure indicator, the ABS, Traction Control, and Brake Indicator lights were on. As soon as I filled all the tires to the specified PSI, that indicator disappeared but the brake related ones all stayed on.
View 10 Replies
This morning after starting my accent the abs, e-brake, and traction lights all came on. What could this indicate, and should I not drive the car till it is fixed? I checked brake fluid levels for the of it, and they were fine.
View 6 Replies
Started my 2010 Prius the other day and the traction control, brake light, abs light and a yellow Astrix light came on and wouldn't go off. The car drives and handles just fine, brakes feel normal. I have tried resetting the lights with a trick with a paper clip someone else posted, but it didn't work for me.
View 7 Replies
I need to troubleshoot a problem with the ABS & Traction control lights on a 2006 Mountaineer Premium with 126,000 miles. During the year that I have owned the vehicle this problem has occurred every time it is driven on a long trip. The previous owner never drove on longer trips so has no experience with this problem.
When you drive the vehicle around town and on shorter trips (less than an hour) there are no indications of problems. The ABS and Traction control lights come on as part of the start-up check cycle and go off. The ABS and Traction control work in low traction conditions and the lights function correctly when either one is activated.
The unusual behavior occurs on trips longer than an hour. Typically after about 1 1/2 hours at highway speed both the ABS and Traction control lights come on as well as the Wrench symbol in the message panel. It you hit "Reset" the Wrench symbol goes away but the ABS and Traction control lights stay on. The brakes work normally. I do not know if the ABS and Traction Control will work. I have never been in a low traction condition when the lights are on.
Both lights stay on until you stop the vehicle and turn off the ignition. When you restart the vehicle the ABS light is on but not the Traction Control light. When you start to drive the vehicle the ABS light goes out immediately.
After about 1/2 hour of driving both lights come on and the Wrench symbol displays in the message panel. Whenever you stop the vehicle and restart during the trip the cycle repeats. The day after you finish the long trip everything is normal for driving around town and on short trips.
View 3 Replies
I am the owner of a 2011 Hyundai Sonata GLS. It has approx 35,700mi to date.
Ive been apart of the forum for quite some time now. Ive been having an issue for a couple of months now with my Traction Control light being stuck on and intermittent flashes of the Brake light (as if parking brake were engaged) and ABS Lights simultaneously.
I'VE ALREADY HAD THE BRAKE SWITCH FAILURE RECALL PERFORMED. When i was having problems shifting and with my cruise control.
This all started this past winter during a bad snow and ice storm we had here in St. Louis, MO. I was on my way to work and the roads were slick with ice and snow. I was traveling no more than 15-20mph on a freeway and as i was approaching a light it suddenly changed to red and i had to slam on my brakes and make a swift right turn in order to avoid hitting anyone in the intersection. Ever since that moment, I've been stuck with these lights on in my dash.
Let me start this by saying I've done a couple of mods to my car. Hids, aftermarket remote start (professionally), aftermarket stereo, amps, new speakers all around, led lights inside, cup holder mod and led tail lights. That's all of my electrical mods.
Ive taken my car to the dealer several times for this problem. They tried hooking my car up to their code machine and they said the car wasn't communicating with machine and it was the first time they've seen something like this before.
They tried pinning the problem on my alarm and stereo. (as they usually do) They said it was a corroded ground. The dealer cleaned that up and said that fixed the problem. In actuality, it didnt. The issue still was there.
Ive had both the alarm and stereo removed to see if this were the cause my issues. NO...the problem still exists.
Here's a pic ....
View 12 Replies
My 12 Escape with the 3.0, shifts fine in warm weather or in cold weather when warmed up. But first thing on a cold morning she's a bit of a screamer getting into the next gear. Is this a signal of something about to go wrong? Is there an easy adjustment? Or this is the way of it and it is fine......
View 14 Replies
well Im working on mother in laws 2002 escape...replacing wheel bearing and ball joints...I went with replacing control arm with ball joint already pressed in , I did try to press out old ball joint first but it wasn't budging...so I went on to the control and the back bolt came out fine...except threads at top of bolt look worn bad...anyways moved on to front and it was tight and moving along good...sprayed down with pb blast moved it back in sprayed again and waited a bit....as I went to bring it back out it snapped....I got the broken bolt out...it broke right at where the threads start...anyways Im having problem with gettting the control arm out while the rest of that bolt is still in there.
View 14 Replies
Changed front brake pads yesterday. Took calipers apart, used c clamp and old break pad to release pressure from the cylinder. Installed new pads. Brakes felt spongie. Drove truck forward and backwards hitting the brakes. They tightened up some what but still spongie. Drove truck with no change. Decided to bleed front brakes. Now I have NO brake pressure at all.
*rotor on left side did have small groove but was not replaced... would this possibly be contributing to my issue.
View 4 Replies
I think I forgot to reset the oil life indicator at my last oil change, however I am not 100% positive.
Is the oil change indicator purely based on time/miles driven, or does it have any sort of sensors that actually detect issues with the oil?
I've heard some vehicles do actually do basic checks rather than purely being time/mileage based.
Anyway, I am no where near the miles or time interval from the previous oil change so if there aren't any magical sensors I'll just reset the life.
View 3 Replies
I recently got an Escape and I am having a issue with the cruise control. That being, it doesn't work. The control module under the hood is all hooked up, the linkage the the throttle body and all. No broken cables.
The brake lights work as intended, and only when the brake is applied. On the inside, the dash-light cruise indicator works fine.
I ran the diagnostic by holding the off button and turning the key on. The cruise light flashes and I begin the sequence. I noticed I was pushing the brake out of habit while running the first few tests. They all returned 2 flashes upon completion of the diagnostic. All other buttons were registered.
Now the strange part, when I took my foot off the brake and did the same test, the final result is three flashes of the cruise light. I understand these flashes represent a fault, and I am having a hard time as I cannot find one.
What do these results mean? I'm thinking the brake being applied gives a fault surrounding the fact that cruise is disabled when the brake is applied.
View 3 Replies
The cruise control has not worked on my 2001 escape since i bought it a few weeks back. i checked the usual culprits and everything is good. i plugged my scanner in and got a control module code.
c1945- park switch indicates park with vehicle moving.
I did do some live data testing and it does infact show park when in gear. the display on the dash shows the proper position.
I am almost certain this is the issue with my cruise. Where this sensor is? Doing a parts lookup isn't showing much.
View 11 Replies
