Ford Escape / Hybrid :: Oil Pressure Light Was Blinking / Now Constant
Dec 12, 2012
I'm having an issue with my ford again. Escape, V6, 123k miles. Recent work done: Replaced all spark plugs, coils, and intake manifold gaskets. Replaced all four O2 sensors. Oil change switching from the 5w-20 to 5w-30 due to it getting cold, (probably a month ago?).
Now for my current problem. Two days ago on a 20* morning, after it sat outside all night, I drove about 3 miles and then noticed the oil pressure light was blinking intermittently. When I came to a complete stop, it stayed lit. I pulled into a parking lot and starting shutting stuff down. I noticed when I turned the heater blower off, the light went out. Turning it on to High, I noticed the RPMS on the tach dropped to around the 500 mark, and the oil pressure light came back on. I turned it off and let it sit for about 45 minutes. Oil is showing good on the dipstick. I then drove it the last two days without the light coming on.
Now this morning, driving it again in 20* weather, after it sat outside, the light came on again, in almost the exact same place away from home. Both times the motor had reached operating temp, with the temp gauge being in the middle between "C" and "H". This time, even with turning the blower off, it came on every time it was at idle. I let it sit another 45 minutes, but this time when I drove it, the light was more intermittent and then was constant.
Again, the oil level is good on the dipstick, and the motor seems to be running smooth. I'm wondering if this could have anything to do with changing over to a different oil and with it being so cold in the mornings?
I have it written down at home, but I can't remember when I did the actual oil change, but its probably been a little over a month. I went from 5w-20 Pennzoil, to 5w-30; wix filter. I'm planning on doing another oil change tomorrow when I get home and go back to the original 5w-20. Also, I'm ordering a new oil pressure sensor, and I'll try that also. I've also looked into an oil pressure tester....
View 14 Replies
Advertisement
We bought a new 2002 Escape 4WD and it has been great. Just clicked 130k. However, yesterday my wife said the car clunked when putting in reverse, and then the OD light started blinking. Shortly after that the Escape would not drive in gear, just a spinning noise. After the car was shut off for a few, it would drive again, but not very far. Fluid is good, and it will only drive for a while. I noticed a broken vacuum line coming from the trans, but could't tell where it went.
View 3 Replies
I have a 2001 ford escape. Today it starts to miss and the engine lights starts flashing. It is never the same amount of flashes. Sometimes its 8 or 10 flashes. I counted up to 25 flashes one or twice It just shakes bad and that's when the flashing starts. When it starts to miss and vibrate, I can accelerate in passing gear and it smooths out. When you hold it at a constant speed it starts missing again. Cannot get a code with my reader. Someone told me a flashing light indicates a misfire. What may be causing this problem?
View 2 Replies
Girlfriends 04 escape airbag light is blinking code 37. Read something about it being on passenger side what do I look for? I just got done putting in 2 coils, 2 cats, egr, o2 sensor, intake gaskets upper and lower, PCV, injector orings all due to misfire sure there not connected just added info. Other problems include heated seat switch lights for a second then shuts off, and no cruise control. Need to get light off for inspection by end of month....
View 2 Replies
I was driving today and felt my ABS kick in with a pulsing pedal, although I was on dry ground. From that point on, my ABS light stayed on and my 4X4 light will blink every minute or so 8 consecutive times. The ABS light has gone off a couple times but only for a second and the ABS light comes back on again. I did get the truck on a scanner and got the codes C1234, U2023, U0415. Tried to clear the codes, but the ABS light prevails.
View 14 Replies
2008 Escape V6
Got the oil changed at Walmart and they told us there was oil in the air filter and we should replace the pcv valve. Before we changed it the oil pressure light had started coming on when the car is stopped, either in gear or park. Once the gas is hit it goes off, even at something like 1 mph. Well I changed the pcv valve but the oil pressure light is still doing the same thing. What should be my next step?
View 2 Replies
With winter on its way I have installed winter tires and steel rims w/o pressure sensors on my 08 Escape. Is there a way to disable the dash warning light for low tire air pressure?
View 14 Replies
I just put on new winter tires and rims on my 2012 Escape and after driving about 6 miles, the low tire pressure light came on. Is there is a procedure to learn the vehicle to the new tires?
View 6 Replies
My friends 2006 Escape has the ( low pressure warning light) flashing on for about 10 seconds after starting the engine. All tires are at correct pressure. What is causing this?
View 5 Replies
No key on prime. Inertia switch OK. Zero line pressure when filter removed & changed. Tries to start with ether. Front 3 coils are for sure firing. Swapped the pump relay with fan relay, no change, no prime.
I'm working with an 03 factory hard copy manual & I'm just not seeing a testing procedure, but I'm bat blind sometimes. What I'm missing? The patient had run fine all day, stopped for an hour. Got back in, started badly, shook somewhat, died, no start since.
View 13 Replies
The facts: 2009 4x4 V6 Escape with Valve stem mounted TPMS
I am getting a tire pressure sensor malfunction fault. The warning light is on and the error message is displayed on the little screen in the gauge cluster.
What I have tried: First I should say I have replace to defective sensor twice now...
1) I put the escape in tpms train mode by hitting the hazard switch off/on about 6 times.
2) I used the train tool to train all the tires but there is one that is giving me trouble and will not train.
3) I tried deflating the problem tire and inflating it to the specified pressure given on the be pillar of the escape (30 psig)... after inflating it I tried to retain it with no luck.
4) I tried rotating the tires and as I mentioned earlier I have replaces the problem sensor twice. Still can't can't get the problem tire to train.
My thoughts:
1) I don't think this is a module error because I can train the other tires and since I rotated them I know their position is not a factor.
2) its possible that I have got two defective tpms sensors but I think that is unlikely.
3) I have read of another procedure to put the escape in tpms train mode that requires you to turn the ignition on/off, step on the break pedal, tap your head and rub your belly, etc... but I have not tried this method. Is there a difference from this train mode verse hitting the hazard switch on/off about 6 times?
4) Does the train tool only work on previously trained sensors? do I need to register the new TPMS sensor with the TPMS module? I have an OBDII tool that connects to scanXL software on my laptop which included the ford proprietary protocol. I looked for a way to program a tpms sensor (similar to how I did it with my toyota) but couldn't find the option.
View 4 Replies
I need to replace my pressure line on my 02 Escape 3.0L. Looking for a DIY for doing this same job?
View 1 Replies
Over the weekend my 2008 Escape Hybrid manifest 2 problems the same day.
1. The remote keyless entry button stopped working (thought it was dead battery in key)
2. Got a error message 'Tire Pressure Sensor Fault'
So after suffering with having to actually unlock my car with a key (heehee/see sarcastic grin) and getting irritated by the error message. I asked the internet about my symptoms. Got the standard answers of "bad tire pressure sensor/reprogram" and change the battery in the key. But ONE and only one person (namely Enviroguy ) said what I thought was going on - that these two problems were related. (afterall it is 2 wireless devices in the car.)
Changing the key fob battery had no effect & Both keys were unresponsive. Seeing what Enviroguy said about certain chargers or wireless devices can cause interference in the tire sensor and keyless systems. .... Then I remember that I had been using a new no-name charger for my cell phone when this problem started.
I unplugged that charger.....(it was a cheap generic power point to USB adapter). The Keyless system is working... ! The tire pressure error has vanished.... !
I did not go to the car appointment.... Now let's hope this was in fact the problem! May my 2008 Ford Escape Hybrid "Be Healed!"
View 2 Replies
Changed front brake pads yesterday. Took calipers apart, used c clamp and old break pad to release pressure from the cylinder. Installed new pads. Brakes felt spongie. Drove truck forward and backwards hitting the brakes. They tightened up some what but still spongie. Drove truck with no change. Decided to bleed front brakes. Now I have NO brake pressure at all.
*rotor on left side did have small groove but was not replaced... would this possibly be contributing to my issue.
View 4 Replies
My 2006 Escape Hybrid with <3500 miles on it had the ABS and 4X4 lights light today when I am 60 miles from home. I had this happen a few years ago, and I replaced a cracked tone ring, driving it to the dealer, who was only 5 miles away. My question is, is it safe to drive home and take it to my dealer who is 60 miles away, or should I have it towed?
The vehicle runs, in fact, the ABS and 4x4 light went out - in fact, I think I saw an indicator message that said 4x4 restored, but I am not sure, it appeared and then was replaced by X miles to empty. I would prefer to go home and take it to the dealer I purchased it from, but I don't want to drive in a car where the brakes may not work. I've read differing accounts on the internet and I can't figure if this is a "service soon" meaning I can make the trip home, or if it will strand me or worse if the brakes will fail on the trip home.
View 14 Replies
Intermittently blinking check engine light in a 2003(?) Ford Escape. I received a call from my fiance, who's about 45 minutes into a two hour drive. On the interstate, her check engine light started blinking, so she pulls off the interstate to a gas station (the light was blinking for maybe five minutes before she could stop, according to her). After she was off the interstate, but before she had turned the engine off, the blinking stopped.
She called me, and I looked up and directed her to an AutoZone about a half mile from where she was. Told her to drive there, and have them to try to read any codes from the engine. She drives over, engine light stays off the entire time. They hook up the reader, and there aren't any codes. My question is, if the check engine light stops blinking, and there aren't any codes for the reader, is the car safe to drive, or will she destroy the cat if she keeps going? Also, it's raining, if that matters for any reason.
View 4 Replies
My ABS light is on and the 4X4 light flashes about 8 times every few minutes. I thought this would be from a cracked tone ring on teh drive axle, I put the truck up on my floor jack and I did find a cracked tome ring on passenger side. Whoever has the truck used silicone to put the broken tone ring back on. In any event I replaced the drive axle with a new OEM with new tone ring. Drives like a charm but ABS and 4X4 light still on and flashing. It is AWd Is there a tone ring on the drive shaft ?
View 6 Replies
I have a 2006 mariner that the ABS light is on all the time and the 4WD light flashes 8 times and the vehicle feels like it is in four wheel drive when turning only at slow speeds and usually in reverse but only when the vehicle has sat for a while, as if you parked for a hour then pulled out of the stall and were turning the wheel.
Tone rings on all wheels are good and all speed sensors have good continuity. Have a friend that works at Ford dealership and he got a tech to scan the car for me. Scan showed the left rear wheel sensor at fault so that's what I'll replace.
View 1 Replies
The O/d light flashed on then off, a few miles later my 06 v6 all wheel drive just coasted to a stop, no noise or anything else. The engine light is on. The trans oil does not smell burnt. The park works but absolutely nothing for the other gears. I drained the tran fluid, 1 gallon came out. Put back in one gallon of new but it is way high on dipstick, the pump seems to not circulate the oil. My car only has 75k on it. What to do next?
View 3 Replies
My son said the high brake light is out, the one on the roof. Bulb is fine. Before I experiment, where to go?
View 2 Replies
I recently purchased a 2008 ford escape, v6, 2wd. When I bought it, I noticed the ABS light was on, and I got an appointment scheduled to get it fixed, but they couldn't get it looked at for 2 weeks out. Needing a vehicle to drive to and from work, I agreed to schedule the appointment, as I test drove it with the light on with no issues.
Well, after putting about 200 miles on it over the weekend, there are now noticeable issues. First off, the parking brake light decided to come on intermittently, and now it comes on and off spiradicly. Secondly, when I drive the car now, I can hear a clunking noise, followed by the traction control light blinking (It was on constant before), and loss of power. I ended up pinpointing that to being the brakes engaging while the car was driving (I noticed when I stopped, the rotors were really hot. I threw a tiny bit of snow on them and they smoked really bad.
I removed the tires in the front, and checked the tone rings, they both appear to have been replaced recently as they are still shiny as if they were brand new. I also took the ABS sensors out, and wiped them down, they also appear to be new (Although the bolts that hold them on clearly aren't new). I don't have access to a high-level scan tool to get it looked at, and I refuse to drive it anymore to take it to a shop just to have it looked at, what else could be causing the issues? It's highly possible that one of the ABS sensors is bad, but how do I go about checking it without just replacing it? Can I use a voltmeter or something to check it to see if it's getting the correct voltage?
I am not sure how the abs system works, but I know that the traction control light is on because the abs light is on, as they both have the same systems they use, but would that also cause the parking brake light to come on, too ? It originally wasn't on, but just started doing it recently. I checked the fluid level, and it's more than within range. This is my daily driver, and obviously I can't go two weeks without a vehicle, and that's the soonest I can get it into a shop...
View 6 Replies
