Ford Escape / Hybrid :: Engine Stalls - Runs Fine After Key Cycle
Dec 30, 2014
2010 Escape with 74,000 miles. Backstory: This is my daughters car who is away at college about 300 miles away. About a year ago the engine started hesitating when driving and would stall to idle at highway speeds. She took the car in to dealer and they replaced the Throttle body under the CSP that had been issued just prior to the dealer visit. All was fine for about 3 months, then she reports that the car is doing the same thing. Check engine light briefly illuminates and goes right back off when this occurs. She is able to slip the car into neutral and it seems to correct the malfunction. Unfortunately she has gotten so good at this that she keeps her hand on the gearshift when driving. It seems to happen at various speeds with no warning and no lasting effects.
She came to visit for Christmas and I was able to replicate the problem after about 30 minutes of city driving, but not quick enough to take a picture of the wrench that illuminated briefly. I slowed to the edge of the road, put it in park and turned off the key (engine ran the whole time at idle). Cranked back up and good to go! She had the oil changed about a thousand miles ago, I replaced the air filter last night and she had to return to her house for work in the next couple of days. She said it happened 5 times on the way home last night.
Car has always been serviced regularly and was a certified pre-owned when we bought it in March or so of 2012. I also bought the extended warranty although that may be expired by now.
Her local dealer said they can't fix it if the CEL is not on or the problem is not occurring at the exact time they have it in the shop. Now, I am not sure but was under the impression that the computer would record any codes and store them even if the light went off and the car returned to normal.
View 6 Replies
Advertisement
I have noticed that my vehicles engine fan runs at max speed (and is very loud) all the time. Regardless of outside temperature, engine temperature, climate control settings, etc. It runs like that from the second I turn it on until I shut it off.
I have done some research online and found that people with a similar concern have been told that it could possibly be either the Coolant Temperature Sensor and/or Cylinder Head Temperature Sensor. I know that it could be a wide variety of issues, however it seemed as though these were common (and relatively easy) solutions. Does anything think either/both of these could be the problem? If so, need info about the proper part and instructions/video on how to install the new parts.
I would much rather spend ~$50 for two parts than screw around taking it in. If my attempts dont work, at least I know that I have 2 new parts in there. Or is this not really anything that I should worry about?
Additionally, my climate control settings dont all work. And I have found through research that I need to replace the blower resistor. Would this have any impact on the engine fan? I drive a 2012 Ford Escape XLT 3.0L V6
View 5 Replies
I just picked up a 2004 ford escape and information is difficult for me to obtain. Person I purchased from had all new suspension installed. Says it needs new transmission.
My indications: Vehicle starts right up dies/stalls with anything above throttle. Major lack of power. Was able to put in Reverse and it moved a bit and same as drive. Smoke from rear of engine. Seems like coolant dumping into exhaust. shake on exhaust you can hear slosh slosh in exhaust.
No engine trouble codes no lights on dash.
Am I looking at a headgasket? This has the 3.0 duratec v6 with the water pump belt driven by the cam on the driver side. Open up the oil cap there is the timing chain. serpentine belt is on passenger side of engine. There is no coolant/water in the engine oil but the coolant is disappearing FAST. no coolant on spark plugs that indicate its in the cylendars.
Was going to check compression but the compression tester I have only threads up to 14mm. to small for the hole. I can probably rent a tester with proper sizes if needed. Fuel pressure at the rail primes to 60 psi and stays there. Stays at 60 psi while running as well.
View 11 Replies
The cooling fan runs on high as soon as the a/c is turned on, regardless of the engine temp. I have the sensor(6F9Z-19D594-AA) that mounts on top of the accumulator. If i replace the existing sensor, will the refrigerant leak out?
View 10 Replies
Let me start with I have a 2003 f250 5.4. The motor blew on my truck and I had a 100k motor dropped in it. I've put new spark plugs, ohmd out the coils. I tried both sets of injectors. cat delete and new fuel pump. It has rough idle and stalls but runs fine at higher rpms. Also has basically no brakes. I am thinking vacuum but I've check all the lines. No codes either!! also cleaned throttle body.
View 4 Replies
I have a 2001 Escape I bought new so many years ago. It only has 90k miles. The other day I drove it to work running fine. It rained REALLY hard that day and when I came out to go home it would barely start, missing really bad. Limped it home and into my garage where I examined it for water under the hood. Nothing. Started pulling things apart, nothing on the engine, around the coils, in the spark plug conduits, etc., dry as a bone. Let it sit for a couple of days and no change. Replaced the coils just for grins. Drained the fuel from the injector assy, looking for water. Nada. Verified spark, fuel, compression. Still, very difficult to start and when it does it's only running on cyls 1,2 & 3 because I can disconnect the coils on 4,5,6 and it makes no difference.
View 6 Replies
2004 Ford Escape 2WD 3.0L with about 81,000 miles.
Problem: 2 possibly related
1) If warm up (get to about 190+ degrees) and then cut off engine. Does not start. If I wait about 30 secs and play the gas pedal, then I can get it to start with high revs and after about 15 secs runs normally. Or, I can disconnect the air intake and it'll start fine. But if you stop and try to start again, no joy unless playing with gas pedal.
2) After driving about 20-25 mins, it seems to randomly stall-out while going about 40 mph. When it stalls out, it will restart again after about 30 secs.
Note: Neither of the above throw any codes.
Here's my problem chart after mining the other posts:
Thing to replace/do //// No Code /// Stall while driving /// Won't restart when hot
Fuel Pump //// Yes /// Yes /// Doubt it
Fuel Filter //// Yes /// Yes /// Don't think so
CKP Sensor //// Yes /// Yes /// Yes
CMP Sensor //// Unlikely /// ? /// Possibly
ECT //// Maybe? /// Yes (if too hot) /// Yes
IAC Valve //// Unlikely /// Yes /// No
Thermostat //// Yes /// Yes (if too hot) /// Yes
MAF sensor //// Unlikely /// No /// Yes
What I've done:
- Well, I started looking at the vacuum lines and they were crumbling so I replaced all those (to EGR and all that).
- There is a mystery line that appears to come up from the canister and go to nothing--is this some kind of atmospheric vent?
- My cheap scan tool also shows engine temps getting up to 216 degrees if I make it work (idle high at 2000+ rpm), so I'm suspicious of the cooling system and thinking maybe the ECU is shutting down to avoid overheating.
I'm going to start with flushing the coolant and replacing the ECT and thermostat while doing so. This is relatively inexpensive and ECT can do weird things. The restart problem is consistent, so I'll know if I fixed that right away.
View 2 Replies
2002 3.0L escape 4WD, stalled twice on me when shifting into reverse after a complete stop. No CEL, truck started right up again....
View 4 Replies
The car has 130K on the clock, and I don't know if she's had the plugs replaced, but the car has been stalling on her suddenly once it warms up, like the ignition switch is switched off. Then, once it cools down for a night, it runs again. If it only cools down for an hour or two, it will run but only for a few miles before quitting again. I'm thinking a sensor, pcm, or coils, but I'm hoping there's some way to narrow this down a little bit.
View 10 Replies
1992 Mercedes 300E with 160,000 miles that I've owned for 15 years. Car runs fine for approximately 10-20 minutes and then starts to sputter and cough and if I don't increase the RPM's it will stall. If I increase the RPM's it will smooth out for a little while, but after a couple of minutes with higher RPM's it will sputter again and finally stall. After it sits for awhile I can start it up again and it runs fine for another 10-20 minutes. No check engine light is on and the car is OBD 1.
This problem preceded the weather recently turning cold. Thus far I replaced the spark plug wires as the other ones were old, but this didn't work. The spark plugs themselves were replaced about 2 years ago. At this point I'm suspecting it needs a new distributor cap and rotor (when I replaced the wires some of the cap's posts had corrosion, which I cleaned off with a brush).
View 2 Replies
My 2003 escape stalls from park to reverse and drive,not all the time but when warmed up. IAC motor replaced and still stalls.
View 7 Replies
I drive an 03 Civic Hybrid. Twice, a week apart, while driving about 50, the speedometer goes to zero, then the power steering goes out and I lose power and momentum. The dash indicator lights go on like a christmas tree, engine still running, but car sluggish. I shut it off, and then get no power at all, not even hazard lights, and car won't start. With jumper cables, it starts right up and runs like nothing happened. IMA and check engine lights are both on, and have been since I bought it three years ago. In those years, my gas mileage has been consistent (42mpg) and no other funny business. Dealer won't work on it except to replace IMA and O2 sensors, which it has always coded for, and would cost the value of the car. What to do?
View 12 Replies
Posted earlier with my escape randomly stalling at idle. Getting a code po446 along with po511. Only stalls at idle after warming up and letting it set a while. When you go to recrank it that is when it won't idle or if it does its at 500 rpms or less. Also after driving it today it smells like rotten eggs. Replaced the idle control valve with no luck. What could cause this?
View 2 Replies
The check engine light came on again after coming on about a week ago and then shutting of by itself. Everything seems to run normal with the car so I don't know if I should ignore the light and just keep driving or what. What would you do? My car is a 2011 Ford Taurus.
View 1 Replies
I have a 2013 Passat TDI with remote starter, when I start the car it runs until I unlock the doors and then the engine shuts off, I know there is something I am doing wrong but can't seem to find the information in the manual on how to keep the engine running.
View 6 Replies
We've had two problems within the last week with our 2002 Sport Trac (4.0l SOHC engine w/167,xxx miles). They may be unrelated, but I suspect there's good change they are. Both incidents happened while my 16 yo daughter was driving, so there's only very limited info on what happens. Both times, when I get there, it starts and runs fine. There is no CEL.
The first time it apparently stalled as she neared her destination after driving only about 2-3 miles at 35 mph or less after a cold start. She was slowing to pull into a parking lot and reported the dash lit up with warning lights, no power steering assist and no power brakes and no power from the engine. When I arrived it started and ran normally. She had fulled up the day before after two days of heavy rain, so I suspected water in the gas. I drove it more than 200 miles within the next 24 hours under a variety of conditions and filled up at a different station. I experienced no problem what-so-ever, and didn't bother adding any dry gas.
Then 5 days later (still on my fill-up) when she tried starting it after sitting all day, she reported the engine started but ran rough before stalling and never idled normally.
Doesn't the fact there's no CEL eliminate a lot of the upstream part of the control system......like sensors and actuators? This leaves things like the downstream parts of the fuel and ignition systems. I.e. from the fuel tank / pump to the injectors and the downstream parts of the ignition system.
What are the possible culprits? Fuel pump, fuel pressure regulator, injectors, ignition module, spark plugs, and....... what else? (I'm not that familiar with what these engines have) And of the possibilities, what are the most likely causes.
View 4 Replies
I have a 2001 Escape with 119,000 miles. I am the second owner, having bought it at 59,000 miles. The engine and tranny operate flawlessly. I replaced the tires that were on it within 10k miles of buying it for I was sick of the pulsing ROWR-ROWR-ROWR-ROWR noise at highway speed.
That noise, couple with the normal Escape noise, drove me nuts. So, I bought a new set of tires, Goodyear RTs. The noise calmed down, but now the noise is back. Alignment has been fine, had it checked, but the tire tech told me "these small SUVS are murder on tires."
I am ready to get rid of it simply because of the road noise at highway speed. My wife complains about it. Compared to her '11 Accord, it sounds like a jalopy. It handles well, no shaking or shimmying.
View 10 Replies
My daughter has a 2002 Escape 4WD with 3.0L engine.
Coming home from school a few weeks ago she experienced engine running rough on the highway when trying to accelerate. We ran the diagnostic on it and it revealed that #2 cyl coil was misfiring.
I've replaced all of the rear bank coils (in hopes that I wouldn't have to remove the intake manifold again anytime soon). I also replaced the connectors and weatherproofed them.
Replaced all the plugs while I had easy access too. This all went pretty smooth with exception of breaking 3 of the 5mm coil bolts off inside the valve cover. I've also replaced the upper and lower intake manifold gaskets.
It runs much better now except now on the highway, at 1800 rpm/55 mph if I try a gradual acceleration I get engine sputtering and it won't accelerate. If I push hard on the pedal it will downshift and accelerate normally right past this trouble spot. Other than this it idles and runs great.
I've noticed that the 3/4 in. vac hose on back of manifold is getting pinched closed about 70%. this is the hose that leads down to the top of engine just below lower manifold. I suspect this is the problem but cannot determine the root cause. I assumed it was the intake manifold gaskets but those are now replaced.
View 1 Replies
What to look for. 2001 escape 3.0 starts and runs but it has a miss and no codes came up yet . the engine will rev up but it really takes time to idle down . don't matter if its cold or hot it just don't want to drop to idle as fast as it should.
View 4 Replies
I have a 2001 F350 with the 7.3 standard trans. The previous owner put a toggle switch to control the EBPV as an engine brake, I've never used it. It blows white/blue smoke when cold but has for the last 4 years and doesn't seem any worse now.
Last fall I ran the truck the lowest on fuel that I ever have, the light was on for a long time and I thought I would run out. I made it to the gas station and filled it up then drove home. The next time I drove it I went about 25 miles and it started to buck while going up hill. This got worse and eventually the check engine light came on and it stalled.
It wouldn't start again so I had it towed home. I got it started a couple hours later but it would run really rough and only for a minute or so then stall. It will usually start again once or twice and stall, then it wont start again until it has sat for an hour or so.
I didn't have a code reader at the time so I started reading threads. Here's what I've done to date.
Changed the oil and filter, it was way over do. New fuel filter.
The oil level in the HPOP stays about an inch from the top, I've checked it a few times after its stalled.
Dropped the tank and cleaned the screens in the pick up, no change.
The ICP had oil on it so I replaced it and a new connector, no change.
Changed the CSP with a grey one, no change.
Changed the IPR valve with one from a buddy that was on an engine that was running. The truck ran rough for a min then settled down and ran smooth. I let it idle for 20-25 minutes with no problem so I thought the problem was solved. After sitting for a month or so I fired it up and its back to running rough then stalling.
I bought a Vgate ELM327 connector and downloaded FORScan on my laptop. (I'm still not sure what I'm doing). These are the stored codes P1281, P0475, P1316, P0478, P0470, P1211. I cleared all the codes. I did a buzz test cold and the Injectors all sounded the same.
I monitored the truck while running (rough) the IPR is staying around19.92%, ICP is 701.4psi. After 5 seconds the ICP starts to climb and so does the IPR, at 12 seconds the IPR is 37.11 and ICP is 1835.1 psi the it stalls. The fuel pw,ms is around 2.50-3.0 until before it stalls, then its 1.66. The only codes that come up are P0475, P0470, B1473.
View 14 Replies
My girlfriend has an 05 ford escape with a 3.0 the car has been well maintained it has 184,000 miles on it. Over 3/4 of the miles were highway. I have noticed that it has had a slight engine ticking noise i have researched and some say the tensioner some say retorque the cams? I have not been around these cars much. I replaced the alternator the other day and serp belt all pullys felt fine. The engine used to tick all the time here lately sometimes when it gets started it does it and sometimes it doesn't.
Also what fluid is supposed to be ran in the tranny the owners manual just says mercon, so do i just run regular strait mercon fluid in it? or does it need like mercon V. The car runs fine i just want to fix the ticking noise if its something major. Just some thing I've hear about on a buddys newer f150 with a 5.4 the oil supply ports that lube the timing chain tensioner got plugged and it developed a ticking noise? I am a mechanic so i can check and do anything i just dont know where to start on this car?
View 1 Replies
