Ford Escape / Hybrid :: Engine Does Rev A Bit More Before Tranny Moves To Next Gear When Accelerating
Sep 11, 2014
I have a 2002 3.0 Escape. All running great. I have a question about where engine load/vacuum is sensed for determining shift point? I replaced all of the dry rotted hoses in the vacuum recently when replacing intake upper & lower gaskets. since then, I've noticed the shift points aren't quite the same as before. The tubing I used was slightly smaller that the OEM, but otherwise, everything is plumbed up as before.
When accelerating, the engine does rev a bit more than before, before the tranny moves to the next gear. I can ease up on the throttle just slightly, and it'll shift up. If I'm not accelerating hard, it seems to shift fairly normal. Going up slight grades it doesn't want to shift as soon as it should, but on level ground it shifts fairly normal under light load. Going down grade it shifts quickly, as one would expect. This is why I felt it might be somehow related to engine vacuum.
Is there an sensor somewhere, a restrictor in the vacuum tubing, or a vacuum modulator I might look at? I've double checked the vacuum tubing and found no leaks.
View 6 Replies
Advertisement
I have a 2001 Escape with 119,000 miles. I am the second owner, having bought it at 59,000 miles. The engine and tranny operate flawlessly. I replaced the tires that were on it within 10k miles of buying it for I was sick of the pulsing ROWR-ROWR-ROWR-ROWR noise at highway speed.
That noise, couple with the normal Escape noise, drove me nuts. So, I bought a new set of tires, Goodyear RTs. The noise calmed down, but now the noise is back. Alignment has been fine, had it checked, but the tire tech told me "these small SUVS are murder on tires."
I am ready to get rid of it simply because of the road noise at highway speed. My wife complains about it. Compared to her '11 Accord, it sounds like a jalopy. It handles well, no shaking or shimmying.
View 10 Replies
My daughter has a 2002 Escape 4WD with 3.0L engine.
Coming home from school a few weeks ago she experienced engine running rough on the highway when trying to accelerate. We ran the diagnostic on it and it revealed that #2 cyl coil was misfiring.
I've replaced all of the rear bank coils (in hopes that I wouldn't have to remove the intake manifold again anytime soon). I also replaced the connectors and weatherproofed them.
Replaced all the plugs while I had easy access too. This all went pretty smooth with exception of breaking 3 of the 5mm coil bolts off inside the valve cover. I've also replaced the upper and lower intake manifold gaskets.
It runs much better now except now on the highway, at 1800 rpm/55 mph if I try a gradual acceleration I get engine sputtering and it won't accelerate. If I push hard on the pedal it will downshift and accelerate normally right past this trouble spot. Other than this it idles and runs great.
I've noticed that the 3/4 in. vac hose on back of manifold is getting pinched closed about 70%. this is the hose that leads down to the top of engine just below lower manifold. I suspect this is the problem but cannot determine the root cause. I assumed it was the intake manifold gaskets but those are now replaced.
View 1 Replies
I thought my tranny shift points had gone a little nutty. This afternoon, it suddenly seemed as if it were starting off in 2nd gear...then the OD light started flashing. Now, when you put it in 1st gear manually, or reverse, it's like it's in park. Can't push the truck or anything...put it in drive or 2nd, and it starts off slowly. Once it picks up speed, all seems well. Definitely not starting off in 1st or going into reverse at all. Have y'all seen this problem before?
View 9 Replies
Having issues with transmission fluid spewing out the dipstick hole? Truck is an 04 Escape and has worked great until I had a rear manifold leaking. I took the truck to our mechanic and he replaced the rear manifold cat converter. He broke 3 of the 4 bolts so he told me he had to roll the engine forward to gain access to tap out the broken bolts. Im sure he took the throttle body and intake off for more room. I Got the truck back and noticed transmission fluid all over my driveway the next day. I contacted the mechanic and he states it was nothing he did and cannot figure why this is happening. Basically told me to fly a kite!
View 14 Replies
So we bought a new to us 04 Escape for the kid, he loves it! My question is, what's going on when I accelerate somewhat aggressively, the tach and speedo peg high and battery light comes on. It does not affect performance and gauges return to normal within a couple seconds.
View 11 Replies
2005 2.3Liter 4wd Mariner, 225k miles
I have been experiencing clunk noise on the front end when braking or accelerating and turning wheels.
I have replaced: front control arms, ball joints, tie rod ends, sway bar bushings and stabilizer links and 2 days ago I replaced strut mounts and bearings.
The steering is smooth after the strut mounts replaced but I can still hear cluck noise mostly on left now when going over bumps, braking and accelerating.
Car also has new engine/trans mounts.
I am so lost right now because I cannot figure out what is it. The only thing I didn't replace are the struts but the I test them and they seem to function fine.
View 5 Replies
My girlfriend has a 2001 Ford Escape 3L, 6cyl. When accelerating there is a loud high pitch whistle/whirling sound. The sound varies with the amount of throttle you give it. More throttle = louder whine. Doesn't seem to do it when idling or coasting. What that could be? I'm about to remove the belt and take a look at the drive belt tensioner and other pulleys.
Just checked pulleys and tensioner and the tensioner seems fine, a/c pulley spins smooth and free no play, alternator spins smooth no play. The belt needs to be replaced. I wouldn't think this would cause such a load whistle under acceleration. I would expect it to do it all the time if it was the belt. I'm looking at the water pump pulley and belt too and they seem ok as well.
View 12 Replies
I have had my truck in the local ford shop because the fluid was a little bit burnt smelling, I had a flush done to it and then afterwards I noticed first gear started hesistating and then would go to second, when it warm it doesn't have any issues, shifts normal, but when cold or starting off even with running in the morning before going to work its still does that, I would like to find out before it starts becoming a serious problem....
View 6 Replies
I own a 2002 Escape, 4WD 4cly manual trans. A couple of days ago, when I left work I stopped at a stop light. I shifted out of gear while I waited for the light to change like I always do. When I went to shift back into gear, I couldn't. I found that if I turned the key off, with the clutch disengaged, I could shift into gear without a problem, start the car up and drive away.
Since the first time this has happened, it has happened a few more times, always when stopped, once or twice while slowing down to stop (low RPMs). Besides all that, the car shifts fine while driving.
View 1 Replies
We bought a new 2002 Escape 4WD and it has been great. Just clicked 130k. However, yesterday my wife said the car clunked when putting in reverse, and then the OD light started blinking. Shortly after that the Escape would not drive in gear, just a spinning noise. After the car was shut off for a few, it would drive again, but not very far. Fluid is good, and it will only drive for a while. I noticed a broken vacuum line coming from the trans, but could't tell where it went.
View 3 Replies
I just picked up a new 2006 Touareg V6 with package 4 Offroad Gray with all the fixin's. I'm still learning all the features of the car, I'm finding more and more innovative functions every day. I did have one "concern" that I have been noticing as I drive around, the transmission seems to want to hunt for a gear... sometimes when accelerating the tranny seems to get confused and shifts up and down suddenly before settling on a gear.
Also, this morning when I put the car in R, it wouldn't lock into reverse, it was stuck in neutral before it dumped into the reverse gear violently. The other thing that I have noticed is that it sometimes locks in gear when moving, it'll hold a low gear and not upshift when it should or it'll hold a tall gear and not downshift (for example it'll be in 6th gear even when I slow down to 20mph and then when I try to speed up it'll stay in 6th gear).
I believe this car is drive by wire and it's the first one that i've ever driven.... i've driven other autos before but they have been much smoother and more "direct" then this tranny. I did have an audi before this and that also wasn't the smoothest auto tranny either, it also seemed to have a mind of its own. Have people had these kinds of problems before and should it be something I should be concerned with or take back to the dealer with my concerns? It is a brand new car, i bought it with less then 30 miles and it has only 400 now. I love everything else about the car, the interior is top notch and the fit and finish is excellent so far, my only concern is the tranny.
View 12 Replies
I am working to analyze my Granddaughters 2008 Escape FWD Auto 2.3 L issues with the Transmission. Vehicle has 142K miles with engine oil changes but no maintenance on the Transmission.
Engine was replaced about 9 months ago with a used 2.3 L with 52000 miles. Engine runs fine with no issues and NO Codes. BUT when driving the Escape I find it starts out in 1st gear and with a little feathering of the throttle will shift at 2600-3200 rpm directly to 3rd gear. (Based on known ratios and rpm vs MPH) Also no OD/ 4th gear. OTHER than the shifting issue it runs fine.Reverse works normally.
Summary: NO CODES from OBDII, NO OD lite ON or flashing, NO leaks, "wrench" light is ON solid after 1-2 miles driving, "wrench" light is OFF on restart but turns ON after 1-2 miles driving, Changed ATF - old fluid was slightly dark but looked and smelled OK - Drain plug magnet had slight coating of sludge - no dirt, metal or other solids. Transmission Shifting Lever properly selects Park - Reverse - Neutral - Drive with a quick/Normal change.
View 9 Replies
After they flashed the TCM (vin 34000). Did not notice this before flash. Mild acceleration in a continuing curve to the right as the tranny shifts to 5th wheel pulls sharp to the right. Like a strong twitch. Also does it in left turn but not as strong. Didn't really bother me (driving wife nuts though, and its her car) in the dry, but Sat. nite on snow/ice scared bejaysus outa me. Felt like I was going to spin. If I lift before shift to 5th it doesn't happen. "Twitch" is about like you would to to miss something in the road. Maybe not that strong. Car thinks continuing radius curve is a decreasing radius turn. Not good. Haven't found the right road to try it under hard acceleration
As an aside, Contis worn out evenly at 10,000 miles. Granted, I did remove a few pieces from them this summer, but overall tread is gone.No binding feeling on dry pavement. It does "crab", or bind at slow speeds tight turns on snow/ice, but so does my Yukon XL in 4wd Auto mode.Have to visit dealer anyway. Service fault workshop light came on a few times. Restart and it went away. And dash wood cracked.
View 3 Replies
What to look for. 2001 escape 3.0 starts and runs but it has a miss and no codes came up yet . the engine will rev up but it really takes time to idle down . don't matter if its cold or hot it just don't want to drop to idle as fast as it should.
View 4 Replies
My girlfriend has an 05 ford escape with a 3.0 the car has been well maintained it has 184,000 miles on it. Over 3/4 of the miles were highway. I have noticed that it has had a slight engine ticking noise i have researched and some say the tensioner some say retorque the cams? I have not been around these cars much. I replaced the alternator the other day and serp belt all pullys felt fine. The engine used to tick all the time here lately sometimes when it gets started it does it and sometimes it doesn't.
Also what fluid is supposed to be ran in the tranny the owners manual just says mercon, so do i just run regular strait mercon fluid in it? or does it need like mercon V. The car runs fine i just want to fix the ticking noise if its something major. Just some thing I've hear about on a buddys newer f150 with a 5.4 the oil supply ports that lube the timing chain tensioner got plugged and it developed a ticking noise? I am a mechanic so i can check and do anything i just dont know where to start on this car?
View 1 Replies
2010 Escape with 74,000 miles. Backstory: This is my daughters car who is away at college about 300 miles away. About a year ago the engine started hesitating when driving and would stall to idle at highway speeds. She took the car in to dealer and they replaced the Throttle body under the CSP that had been issued just prior to the dealer visit. All was fine for about 3 months, then she reports that the car is doing the same thing. Check engine light briefly illuminates and goes right back off when this occurs. She is able to slip the car into neutral and it seems to correct the malfunction. Unfortunately she has gotten so good at this that she keeps her hand on the gearshift when driving. It seems to happen at various speeds with no warning and no lasting effects.
She came to visit for Christmas and I was able to replicate the problem after about 30 minutes of city driving, but not quick enough to take a picture of the wrench that illuminated briefly. I slowed to the edge of the road, put it in park and turned off the key (engine ran the whole time at idle). Cranked back up and good to go! She had the oil changed about a thousand miles ago, I replaced the air filter last night and she had to return to her house for work in the next couple of days. She said it happened 5 times on the way home last night.
Car has always been serviced regularly and was a certified pre-owned when we bought it in March or so of 2012. I also bought the extended warranty although that may be expired by now.
Her local dealer said they can't fix it if the CEL is not on or the problem is not occurring at the exact time they have it in the shop. Now, I am not sure but was under the impression that the computer would record any codes and store them even if the light went off and the car returned to normal.
View 6 Replies
I have a 2001 ford escape. Today it starts to miss and the engine lights starts flashing. It is never the same amount of flashes. Sometimes its 8 or 10 flashes. I counted up to 25 flashes one or twice It just shakes bad and that's when the flashing starts. When it starts to miss and vibrate, I can accelerate in passing gear and it smooths out. When you hold it at a constant speed it starts missing again. Cannot get a code with my reader. Someone told me a flashing light indicates a misfire. What may be causing this problem?
View 2 Replies
Engine light flashing constantly with a vibration. It don't give any codes with the reader.
View 1 Replies
Well, not an escape, it is a mazda tribute. but it is the same thing as an escape. My sister just called. as she is driving down the road, if she lets off the throttle the engine will randomly die. it did it 2 times sunday, once yesterday, and once today, as she was talking to me. It will not die at traffic lights, just as you let off the throttle sometimes. today it did it at 45 mph. When it dies she just pops it in neutral, restarts it, puts it back in drive, and it is fine. No check engine light after restarting. What I should look at when she brings it over this weekend?
View 3 Replies
I recently had my PCM flashed due to the deceleration safety recall. My engine now revs to 2200 rpm when I start it even if the engine is hot. It goes down to 750 rpm after about 30 seconds. My engine before the recall, reved from 1200 to 1400 rpm when starting. My dealer and ford tell me 2200 rpm is normal but I think it is too high.
View 7 Replies
