Get a set of real gauges if you want to do diagnostics. 110 psi on the low side indicates that the system isn't running at the time and that the underhood temp is around 100 F.
View 1 RepliesI have a 2001 Escape XLT (3.0) and after getting some wonderful info here regarding my upper/lower intake problem, I thought I would ask about my weird liftgate problem. When I first got the Escape a few months ago, the liftgate opened fine, but it wouldn't lock at all. Then one day for no apparent reason, it stays locked no matter what I do. Some days it opens fine, other days it doesn't.
At some point I made a connection between the Window Lock button on the driver control panel being in lock/unlock mode determining if the liftgate would stay locked or not, but it doesn't always do the trick. So now I am at a loss as to what is causing this. Its very inconvenient to have to go over the back seats to load items into the trunk area, and its also a security issue if I cant get the liftgate to lock when I want it to. Is this still a liftgate actuator issue? or is it a wiring or fuse issue?
I am working on a 2006 Escape that originally came in with a misfire. It had three bad coils, and they had burned out three of the coil drivers in the computer. It had a new computer put in, but will not communicate with the scanner now to program the keys. The old computer would still communicate, and the vehicle can be started and run on three cylinders with that computer, but unfortunately it needs to run a bit better than that. Is there something I am missing about getting communication with a new computer?
View 7 RepliesMy wife just picked up the 2015 Escape 3 weeks ago. This is now the 3rd time back to the dealership with it where nothig on the dash is working. No information center, no speedometer, no tach, no fuel gauge, no temp gauge, and even the entire media screen is powerless. So in turn, a lot of the temp controls and radio are gone.
The first time was on a weekend, I pulled the fuse that powers the entire dash to check it, it was fine and upon putting it back in, everything worked. Still had it to the dealer and they couldn't find anything wrong with it. The 2nd time was this past weekend, we decided to leave it so the service team could see what we were talking about. They again, reset the fuse (still wasn't blown), tightened a couple connections, but really couldn't find anything wrong with it.
The 3rd time was just this morning and the vehicle is currently with Ford now. Obviously warrantied, but did their dealership find what the issue was? We really love the Escape, when everything works right.
The cruise control has not worked on my 2001 escape since i bought it a few weeks back. i checked the usual culprits and everything is good. i plugged my scanner in and got a control module code.
c1945- park switch indicates park with vehicle moving.
I did do some live data testing and it does infact show park when in gear. the display on the dash shows the proper position.
I am almost certain this is the issue with my cruise. Where this sensor is? Doing a parts lookup isn't showing much.
I am having an issue with my 2008 Ford Escape XLT. It seems that my A/C and Heater fan isnt working properly. Basically, air only comes out when i put the fan speed to 4. With 1-3, no air comes out. If the A/C or Heat is on, I can feel cold air or heat coming out but the actual fan isn't running. It only runs when it is set to 4. What the problem could be?
View 7 RepliesShe has a 2010 Escape 4-cyl and the A/C isn't working. It's miserable hot and she has small kids.
The compressor won't start. I put a gage set on the low pressure side and it's sky high, so it should be coming on at least. I also used a Launch scan tool on the OBD port and the HVAC control is commanding the compressor to start, so it's not that - which leaves the $300 compressor or the $9 a/c relay as the next steps. Unfortunately, I only see this car occasionally so I haven't really been able to get under it to check for voltage at the a/c compressor or see if it's a ground issue, etc.
I'd like to go after the relay next but can't find a a diagram I trust as to which one it is. I've heard mention that it's the WOT relay and also that there's an A/C Clutch relay. Any reliable schematic of the underhood fuse block and which position it's in? I took the cover off and they're numbered but there's no map. Also, what p/n is the relay? I'd like to just pop in a new one and see if it takes care of it.
I thought my tranny shift points had gone a little nutty. This afternoon, it suddenly seemed as if it were starting off in 2nd gear...then the OD light started flashing. Now, when you put it in 1st gear manually, or reverse, it's like it's in park. Can't push the truck or anything...put it in drive or 2nd, and it starts off slowly. Once it picks up speed, all seems well. Definitely not starting off in 1st or going into reverse at all. Have y'all seen this problem before?
View 9 RepliesThe passenger door on my 2002 Escape is locked and the power lock is not working on that door. The door is closed, how to get it open.
View 14 RepliesBlower motor only seems to be working on the 3 & 4 position? Resistor bad? What is the location?
View 1 Replies2002 Escape. The over drive deselect button stopped working on my wife's escape. Is their a fuse other than the box under the hood? Transmission was rebuilt not too long aga and has been running fine till the other day.
View 2 RepliesCouple weeks ago, was in a spot that needed 4wd. Turned the switch, the 4x4 dash light came on, but rear wheels didn't do anything. Lucky that we were able to get out with ft wheels only. Has 3.0, xlt version.
View 13 RepliesSo I am changing my transmission fluid tomorrow and was wondering a few things.
1. I noticed some people pull off the transmission hose to the inlet and keep draining that until its clear. For a drain and fill do you do it like that or just pull the plug and refill?
2. When youre filling it back up you just measure how much you taken out and then fill the rest by the dipstick? Anything else i should know?
3. Since I havent changed my transmission fluid in 60,000 miles. I wanted to do a drain and fill. I was thinking I needed to drain and fill it 3 time to catch up to maintenance. How often would you do it to get it clear? Drain and fill then drive it for a week then drain and fill? Or do it all in one day?
Background: No A/C. Identified Clutch had completely failed. I replaced the clutch.
Status: I turned on the A/C and I saw the clutch come on...it was on for maybe 60s. During that time, the vents started to get cold! After 60s it never came on again.
Troubleshooting: I have refrigeration gauges but not much idea how to read the result. I hooked them up and noted about 350psi for the HP side, and about 100psi for the LP side. I think this tells me I should have enough charge in the system to cycle the compressor.
At this point I don't want to start random troubleshooting as I don't want to touch the refrigerant loop more than necessary. A few questions:
1) The HPCO switch, I was reading that it's mounted on a Shrader valve. Is this the case? I'd like to remove it and test at which point it switches. I have not tried bypassing it.
2) Do our vehicles have a temperature sensor near the evaporator? If so, whereabouts is it located?
My 2006 Escape Hybrid with <3500 miles on it had the ABS and 4X4 lights light today when I am 60 miles from home. I had this happen a few years ago, and I replaced a cracked tone ring, driving it to the dealer, who was only 5 miles away. My question is, is it safe to drive home and take it to my dealer who is 60 miles away, or should I have it towed?
The vehicle runs, in fact, the ABS and 4x4 light went out - in fact, I think I saw an indicator message that said 4x4 restored, but I am not sure, it appeared and then was replaced by X miles to empty. I would prefer to go home and take it to the dealer I purchased it from, but I don't want to drive in a car where the brakes may not work. I've read differing accounts on the internet and I can't figure if this is a "service soon" meaning I can make the trip home, or if it will strand me or worse if the brakes will fail on the trip home.
I just bought a 2010 Escape XLT 4 cyl. The mpg is showing to be 16.7, which is really low compared to what it's supposed to be. I bought it off of a car lot and it had been discounted so I'm guessing it was sitting there for a while before it was sold. Do you think that would cause the mpg to be low? I've driven it on the highway and around town. I've had it for 2 days, but it's freaking me out thinking that there is something wrong with it.
View 4 RepliesOk, so I've got a little of an odd issue. It seems that no matter what I do, the AC is always active. Today I reverse flushed the heater core in my 02 Escape, and verified all hoses were clear. I replaced the thermostat housing (other thread) along with a new thermostat.
But, when I run the car, even with the heat full up and the selector set to the defroster and floor, the ac still blows ICE cold. It seems like it is still engaged no matter what. Winter is coming and I dont want my daughter to freeze (her truck).
Had to change the alternator in the 3.0l fwd escape. if some one knows of an easy way to get it out i would love to know. We had to take the manifold cover off right down to the "o" rings as well as what ever we could undo to make a gap between the engine and the fire wall. it took us so long that the repair shop was closed and we had to leave my engine apart overnight with tissue stuffed in the pistons. The one part you know your going to have to get to to fix, and it's almost impossible to get at. It would have been easier to tilt the engine, but we had no hoist, is there an easier way...
View 14 RepliesHow can I test to find out if there is water in my fuel tank , fuel lines, etc. The symptoms are obvious, how do I test for sure. In the event that I'm correct, what can I do to get it out of the tank and fuel system.
I suspect that a lower form of life has put water in the gas tank of my 2003 Escape 3.0L . I sent it to a shop, that was a nightmare . They came up with every misfire and etc. Including bad windshield wipers burned out light bulbs .
Trying to sell me new coils plugs , etc etc ... even though I kept telling them that of course its misfiring if there is water in the fuel. Please test for water in the gas .
I finally went and took the car with intake plenum pulled off. Paid them half of R&R for pulling the plenum and I'm back to square one. They did everything but check for water in my gas tank or fuel lines.
I only have one key and 2 FOBs for my 2005 Escape, but I do have the key number (4 digits plus a letter). I understand I need more than one to program another myself. Is there an inexpensive way to obtain/program a backup key?
View 9 Replies My daughters 2010 Escape (V6 - 3.0L motor) had the check engine light come on back in February, while she was away at school. Well, now she is home and I want to fix it. I have tried all the things I can think of and have found on the web, but no success. I pulled the whole Evap canister assembly down and tested the Evap vent solenoid by itself, and it works (opens and closes). Physically can see if cycle when I apply 12v to it. When I reinstalled it I cleaned up the o-rings and lightly greased them up to seal better in case they were leaking by. Before pulling the whole unit down, I checked and with the key on, there is 12v on the plug feeding this solenoid, but I physically wanted to see it move and it looks good.
Next, I pulled the hose feeding the top of the purge valve, located under the hood, to see if I had vacuum leaking when the car was running. I did not, so if I understand the operation correctly, I am good there as well. What else could be causing the car to dump this code??