Ford Escape / Hybrid :: 2010 - HVAC Blower Motor Only Seems To Be Working On 3 And 4 Position?
Dec 19, 2013
Blower motor only seems to be working on the 3 & 4 position? Resistor bad? What is the location?
View 1 RepliesBlower motor only seems to be working on the 3 & 4 position? Resistor bad? What is the location?
View 1 RepliesI have a 06 Mercury Mariner and this past week fuse #26 keeps blowing turning the HVAC blower motor off. I replaced the blower motor since i had one already in the garage and same thing is happening. The AC will run for awhile and in about 10/15 mins the fuse will blow. Fuse #26 is the Climate control system mode switch, are these known to go bad? Is this the part I should replace or look for other problems IE compressor?
View 2 RepliesI bought my youngest daughter a used 2009 Ford Escape (out of warranty) a week ago. Manual HVAC controls, 3.0 V6, AWD, 73K miles. The HVAC blower motor do not seem to move any air on speed 1 and 2. However speeds 3 and 4 appear to operate normally. Speed 4 noticeably puts out more volume of air then 3. Each 3 and 4 operator what seems to be normal speeds for their setting.
I would normally suspect resistor but my experience is usually that you have all or nothing not it's partially working like this is. I don't mind throwing a new resistor in there and trying it but I rather come up with a better way of troubleshooting it then throw parts at it.
Where the blower motor resistor is located on the '05 model.
View 11 RepliesMy HVAC blower motor stopped today while the wife was driving the F250. I thought I should swap relays (with the heated mirror relay - same Ford Part Number) to rule it out or identify it as the culprit. However, since these are close to the firewall, I have a hard time getting the grip and leverage to pull the relay out of the Battery Junction Box (BJB). How to make this a bit easier?
View 5 RepliesShe has a 2010 Escape 4-cyl and the A/C isn't working. It's miserable hot and she has small kids.
The compressor won't start. I put a gage set on the low pressure side and it's sky high, so it should be coming on at least. I also used a Launch scan tool on the OBD port and the HVAC control is commanding the compressor to start, so it's not that - which leaves the $300 compressor or the $9 a/c relay as the next steps. Unfortunately, I only see this car occasionally so I haven't really been able to get under it to check for voltage at the a/c compressor or see if it's a ground issue, etc.
I'd like to go after the relay next but can't find a a diagram I trust as to which one it is. I've heard mention that it's the WOT relay and also that there's an A/C Clutch relay. Any reliable schematic of the underhood fuse block and which position it's in? I took the cover off and they're numbered but there's no map. Also, what p/n is the relay? I'd like to just pop in a new one and see if it takes care of it.
I am struggling with it, and need to get it done - by myself, as I can't afford a service job. I am handy, and comfortable doing it, But I am confused about how to get into the blower housing.
View 4 RepliesJust got back from a 1200 mile camp trip pulling an 18K toy hauler. 500 miles into the trip the HVAC blower stopped working. Right after the torrential downpours we had last week. Did some limited checking and found the relay under the hood real hot. Swapped it out with the DEF relay and no luck. All the fuses were good.
This was in the Littleton, MA area. Dragged the truck and camper to a Ford dealer who had no interest - "make an appointment for sometime next week". Dragged the trailer to another Ford dealer who was equally not interested. From here we towed the 130 miles to our next stop.
You really miss your HVAC when you have to drive with all the windows open and two fur dropping Golden Retrievers in the back seat. The fur just circles around and ends up either in your eyes, nose or mouth.
Next day I was off in search of a repair. 20 or so miles north I find the next Ford dealer not intrested. Now I'm pissed and rant a little bit at the dealer.
I did almost 20 years in new car service, all highway dealers. Not once did we turn down a vacationing family on the road with vehicle troubles. We have even done engines and transmissions for travelers broken down.
60 miles to the next dealer in Laconia, NH, Irwin Motors, Ford, Lincoln and Toyota.
Same initial story “we are really busy and backed up”.
But, if I was willing to wait a little bit they would see what they could do.
45 minutes later I get the news that I need a blower motor and it is ordered.
No problem. I show up at 2, park the 5<sup>th</sup> wheel in the lot and at 3:30 we have a free wash coupon and we are on our way. And the service people couldn’t have been more pleasant to deal with. Even the techs came out to visit the dogs as we were walking around. 5 stars for Irwin Motors.
I have a 2005 Escape Hybrid. Last summer, the A/C went out, so when in the fall I finally got around to having the cooling system flushed. Did the trick, and A/C works fine. Now that winter's come along, I've noticed an issue with the heat. All fan speeds work correctly, and the dash controls for heat and cold work properly. But what's odd is that I get plenty of heat when the vehicle is at speed, above about 30 mph. As soon as I slow down below that, or hit a red light, there's no heat. The blower just blows cold air until I am back up at speed again.
View 9 RepliesI have a 2010 Toyota Camry 2.5L. Suddenly the blower-motor stopped working. I looked at the under-hood fuse panel and noticed a few of the fuses in the fuse bus-bar were blown, however I'm not sure how the bus-bar is removed. Is this most likely my blower-motor problem? If so, how do I replace those fuses?
View 6 RepliesThe ac/heater works just fine. But the air only blows from front vents towards face; even if i press button to defrost or floor or frontnfloor.
View 1 RepliesI have a 2001 Ford Escape 3.0 4WD, it has a rattle in the motor and no acceleration... Bought the escape with the rattle when you start it up and put into drive it wont accelerate. Transmission is good...
View 3 RepliesI have a 1989 towncar. The blower motor works in any selection (vent, panel, hi-low, mix, defrost) but does not work in the "floor" position. It also turns off in the off position as it should.
I changed out the entire climate control assembly with another one from a junkyard. I thought the function selector electrical switch might be bad. However, the blower motor still does not work.
I am pretty satisfied with the performance of my 2009 Ford Escape. Two years 51,000 miles after I find that the rear door does not open. Following threads of earlier Escape models I find how to remove the inside panel and open it manually. After a thorough study all I need is a replacement latch motor. The plastic latch cover has the following number GA6 GF30.
View 14 RepliesI have a 2012 ford escape with dual climate control with sync but not the touch system. Got in the car this morning and the blower isnt working at all. Thought it was a fuse, nope thats fine. Checked online and thought it was the blower resistor but he said the lower speeds would go if it was the resistor. He said that I need to reset the system and there is a procedure to do this involving pressing various dash controls.
View 7 RepliesThe wifes 2011 Escape battery was dead. Charged it and also found that the rear wiper motor was not working. But it was very hot to the touch even with the car shut off. It was killing the battery. I wonder if the wiper needs to complete it's cycle to shut down. It won't work. Again it gets very hot even with the car shut down for the day I believe killing the battery. Also how can the wiper motor assembly be removed?
View 3 RepliesA couple of weeks ago I got a check engine light. Pulling the codes I saw that it was a p0304 and sometimes a p0316. The first time this happened I check the spark plug cables and one was loose (cycylinder 4). Then last week my fuel pump died. since then I have gotten the two codes on a somewhat continous basis. I replaced the plugs (needed to anyway) and the problem did not go away.
The odd thing is that the check engine light does not come on at idle. IT only comes on after the motor is at a higher rev. The replaced plugs looked pretty normal, but the cylinder 4 plug had some carbon deposits. I am currently running injector cleaner in the gas. I may go ahead and replace the plug wires since the current ones are high mileage and it is not an expensive fix.
I have a Full Size 93, 5.8L Van. The blower motor has stopped working. I have checked the fuzes, ok. I have checked the Power Distrubution Box, ok. I do have power to my Aux (rear) blower. I have hot wired my blower motor, it works. I have no power to the blower motor, thermal limiter, or to the fan control switch on the dash. (Like I said, the Aux on the dash works). What else is there?
View 14 RepliesGet a set of real gauges if you want to do diagnostics. 110 psi on the low side indicates that the system isn't running at the time and that the underhood temp is around 100 F.
View 1 RepliesMy 99 f150 blower motor and blinkers slowly but surely went out on me. The hazards still work. I changed the flasher relay and the relay for the blower motor, and nothing. I've checked all the fuses, and checked for wire issues and nothing.
View 4 RepliesI am working on a 2006 Escape that originally came in with a misfire. It had three bad coils, and they had burned out three of the coil drivers in the computer. It had a new computer put in, but will not communicate with the scanner now to program the keys. The old computer would still communicate, and the vehicle can be started and run on three cylinders with that computer, but unfortunately it needs to run a bit better than that. Is there something I am missing about getting communication with a new computer?
View 7 Replies