I have a 2009 Ford Escape XLT, 4 cyl. and in the summer I had the vehicle in as the speed sensor failed. Since that time I have an ongoing ticking sound (sounds like a diesel vehicle). I had the vehicle into my local dealer and after looking over the vehicle they stated that it was "normal". However, my warranty is up in January 2014 and this sound is horrible. Below is a video of the sound.
[URL] .....
The facts: 2009 4x4 V6 Escape with Valve stem mounted TPMS
I am getting a tire pressure sensor malfunction fault. The warning light is on and the error message is displayed on the little screen in the gauge cluster.
What I have tried: First I should say I have replace to defective sensor twice now...
1) I put the escape in tpms train mode by hitting the hazard switch off/on about 6 times.
2) I used the train tool to train all the tires but there is one that is giving me trouble and will not train.
3) I tried deflating the problem tire and inflating it to the specified pressure given on the be pillar of the escape (30 psig)... after inflating it I tried to retain it with no luck.
4) I tried rotating the tires and as I mentioned earlier I have replaces the problem sensor twice. Still can't can't get the problem tire to train.
My thoughts:
1) I don't think this is a module error because I can train the other tires and since I rotated them I know their position is not a factor.
2) its possible that I have got two defective tpms sensors but I think that is unlikely.
3) I have read of another procedure to put the escape in tpms train mode that requires you to turn the ignition on/off, step on the break pedal, tap your head and rub your belly, etc... but I have not tried this method. Is there a difference from this train mode verse hitting the hazard switch on/off about 6 times?
4) Does the train tool only work on previously trained sensors? do I need to register the new TPMS sensor with the TPMS module? I have an OBDII tool that connects to scanXL software on my laptop which included the ford proprietary protocol. I looked for a way to program a tpms sensor (similar to how I did it with my toyota) but couldn't find the option.
ok this has me stumped I get this buzzing/humming/vibration sound from what seems like around Defroster passenger side but it is not all the time only at higher speeds and it it intermittent . I have removed cabin filter and cleaned filter box and checked for a leaf or something even sealed somewhat the plastic shield that covers the cabin filter. I really don't want to rip dash apart but it is so annoying
View 14 RepliesMy girlfriend has an 05 ford escape with a 3.0 the car has been well maintained it has 184,000 miles on it. Over 3/4 of the miles were highway. I have noticed that it has had a slight engine ticking noise i have researched and some say the tensioner some say retorque the cams? I have not been around these cars much. I replaced the alternator the other day and serp belt all pullys felt fine. The engine used to tick all the time here lately sometimes when it gets started it does it and sometimes it doesn't.
Also what fluid is supposed to be ran in the tranny the owners manual just says mercon, so do i just run regular strait mercon fluid in it? or does it need like mercon V. The car runs fine i just want to fix the ticking noise if its something major. Just some thing I've hear about on a buddys newer f150 with a 5.4 the oil supply ports that lube the timing chain tensioner got plugged and it developed a ticking noise? I am a mechanic so i can check and do anything i just dont know where to start on this car?
Wife's 04 Escape threw the PO136 code for bank 1 sensor 2 02 sensor. Replaced it and light is off. Not convinced something else isn't causing it.
View 3 Replies2004 XLT 3.0L 141K
I just bought the truck on Monday, the CEL popped up on Tues. It shows code 0136. No other codes. CAT "not ready" on scan tool
A google search proved this is a common topic that for some owners is a repeating and cronic sort of issue. What I've read online is that there is an assortment of things that can cause this O2 sensor to throw this code:
Actual bad O2 sensor
Faulty wiring or connection
Misfire throwing mix off
bad convertor
I don't believe this list covers all the accounts I read but these I have were definitely repeat offenders. My intention is to take to a dealer and let them have first crack at sorting it out. I'm handy enough but I see this as something where an unseen detail can drive ya crazy.
Over the weekend my 2008 Escape Hybrid manifest 2 problems the same day.
1. The remote keyless entry button stopped working (thought it was dead battery in key)
2. Got a error message 'Tire Pressure Sensor Fault'
So after suffering with having to actually unlock my car with a key (heehee/see sarcastic grin) and getting irritated by the error message. I asked the internet about my symptoms. Got the standard answers of "bad tire pressure sensor/reprogram" and change the battery in the key. But ONE and only one person (namely Enviroguy ) said what I thought was going on - that these two problems were related. (afterall it is 2 wireless devices in the car.)
Changing the key fob battery had no effect & Both keys were unresponsive. Seeing what Enviroguy said about certain chargers or wireless devices can cause interference in the tire sensor and keyless systems. .... Then I remember that I had been using a new no-name charger for my cell phone when this problem started.
I unplugged that charger.....(it was a cheap generic power point to USB adapter). The Keyless system is working... ! The tire pressure error has vanished.... !
I did not go to the car appointment.... Now let's hope this was in fact the problem! May my 2008 Ford Escape Hybrid "Be Healed!"
Just wanted to post a recent experience I had with the catalytic converter issues Escapes seem to be prone to. A friend has a 2003 Escape 4x4 with the 3.0 V-6 and automatic transmission. It has 141,000 miles on it, she bought it with 40,000 miles on the vehicle.
Recently it developed driveability issues: No power with a whistling noise and top speed of 10 M.P.H. I researched on here and her symptoms matched threads that came up using the search function. I told her I was pretty sure the front cat was bad and had plugged the rear cat, causing the issue. She took it to a local repair shop and confirmed my diagnosis. Their estimate for repair was north of $1,500.00. My neighbor and I were sure we could repair it cheaper.
We towed it to my house and pulled the front and rear-most cats. As suspected they were both bad. The back cat on the engine looked pristine inside so we left it alone. We ordered all of our parts from rockauto. New front and rear-most cats, exhaust and intake gaskets, serpentine belt, and one O2 sensor that was damaged when the insides of the front cat let go.
Installation was straight forward with no major issues. We also changed the plugs with brand new ones she had purchased but never had installed. The vehicle now runs fantastic and she is extremely happy with it.
I'm experiencing the tug/jerk/shuddering in my 2012 Escape v6. It happens more around 70mph or 2,000-2,500rpm.
Tug/jerk/lurch/buck happens even more with OD off. Happens around 60mph or 2000rpm with OD off.
Been to the dealer several times even test drove with a mechanic that acknowledges the tug/jerk sensation. No codes or faults. Last visit the dealer showed me a print out of misfire counts and all cylinders were 0 yet on the drive home it was tug/jerk/lurching.
I have noticed that my vehicles engine fan runs at max speed (and is very loud) all the time. Regardless of outside temperature, engine temperature, climate control settings, etc. It runs like that from the second I turn it on until I shut it off.
I have done some research online and found that people with a similar concern have been told that it could possibly be either the Coolant Temperature Sensor and/or Cylinder Head Temperature Sensor. I know that it could be a wide variety of issues, however it seemed as though these were common (and relatively easy) solutions. Does anything think either/both of these could be the problem? If so, need info about the proper part and instructions/video on how to install the new parts.
I would much rather spend ~$50 for two parts than screw around taking it in. If my attempts dont work, at least I know that I have 2 new parts in there. Or is this not really anything that I should worry about?
Additionally, my climate control settings dont all work. And I have found through research that I need to replace the blower resistor. Would this have any impact on the engine fan? I drive a 2012 Ford Escape XLT 3.0L V6
Recently picked up a 2007 Escape with 108,000 miles. The vehicle is in great condition with a full service history. Recently I've noticed a bit of shimmy in the steering wheel and noise from the front drivers side wheel accompanying the shimmy.
At speeds of 50mph+ the shimmy will start. When going straight there is not much of an issue but when a gradual right hand turn on the highway the shimmy starts. Back to straight and it goes away. Not really noticeable on left hand curves.
Steering issue?
Tie Rods?
Bearings?
I'm going to dig into it to get it fixed.
I've read quite a bit in various threads about the large vacuum elbow collapsing, causing erratic idle speeds. My 2001 3.0 had that issue int he past. I shoved a 1/2" copper 45 degree elbow inside of the rubber elbow, and the problem was solved... until a few days ago.
We're now getting into the hot part of summer here. I've notice the same symptoms are beginning to return, once the engine compartment gets hot. My question is... is the large vacuum line a "hard line" all the rest of the way to the engine, or are there other places along it's length that can also collapse under vacuum?
My wife has a 2009 Ford Escape limited with the six and awd. Lately with all the snow we have had we have found that the 4wd will not engage. I don't hear any clunking noise coming from a possible axle failure or the PTU grinding. Just how does the AWD work on these newer escapes. When does it know to engage? My mother in law's 01 is very trustworthy and keeps plowing the roads while our 09 sits at the road parked. With the surprise snow fall we got today my only alternative was to fire up the Duramax and pull it up our driveway to the street. Something that I can do in the driveway? I'm in hopes that I hay have overlooked something.
View 5 RepliesI have a 2009 Escape, 2.5l engine and manual 5 speed transmission, 205,000 miles. It has has an intermittent miss that has been getting gradually worse over the past 3 months or so. I've been seriously futzing with it for the past 2 months, so far no luck. Definitely worse when it's cold. Not noticeable at all in gears 1-3 (even when cold), noticeable in 4th, mostly between ~2000-2500 RPM, and pretty bad when cold in 5th in the same RPM range, still noticeable when warm. No service engine light until today (#1 misfire).
If I let the vehicle idle for 10 minutes or so, the miss is much less noticeable. Replaced the plugs, absolutely no difference. Bought one COP and cycled through all cylinders, no difference. Finally broke down and took it to the Ford dealership where I bought it new and had them do a power balance test, which isolated it to cylinder #1. Swapped the #1 and #2 injectors and took it back to Ford, still showing cylinder #1. Did a compression test, #1 and #2 both around 165lbs, #3 and #4 both around 185lbs.
I'm a electrical engineer, so I spent some quality time with an oscilloscope to compare the drive waveforms of the #1 and #2 cylinder COP and injector...both COP and injector drive waveforms look identical when comparing to #2 cyl. Tried heating the PCM, made no difference (engine was cold, PCM was hot).
So it finally DID throw a code today, cylinder 1 misfire. I'm thinking I can almost hear a miss at idle now. And listening to the valvetrain at idle, there is unmistakably more valve noise coming from the #1 intake area than the other cylinders, but not terrible.
I am experiencing some strange behavior from my 2008 Ford Escape LTD. At low rpm's, usually when I am going uphill, the engine sounds like a diesel at low throttle and low rpm. It sounds fine at idle, but as soon as I apply light throttle I hear the characteristics rattle of a diesel engine. The engine returns to normal once I get above 30-40 mph or so.
My escape is at 99k miles (bought at 89k) and I'm not sure what maintenance was has bee done on it (sparkplugs, timing belt, etc?). (I do have an OBDII reader)
Where I should start looking for the root cause of the following leak? My wife noticed that when it was raining water dripped off the handhold by the front passenger seat. The ceiling liner is dry, no evidence of water soaking into it. I am thinking windshield or door seal as there is no moon roof and the liner is dry but before I start tearing into it I want to see if there is even a chance I can fix it myself.
View 3 RepliesI have a 2009 Escape that has developed a clunking noise in the right rear. On any bumpy roads it sounds like the shock tower lost it's top bushing but it could also be coming from somewhere lower. It also seems like the truck drifts to the right on bumpy left hand turns, kind of scary.
View 1 RepliesI have a 2001 Escape XLT, when driving thru a parking lot or otherwise at slow speed and hitting bumps, I can hear a clunking sound from the right front tire. Its especially bad if I drive over cobblestone or on a dirt road. Could this be the CV joint? Ball Joint? How can I tell what it is?
View 4 RepliesSo heres the story..........'02 Escape, 179K miles, just had the oil changed 2 weeks ago, ever since then I've smelled oil burning when the car starts up and every now and then after exiting the car. Also have had the check engine light on intermittently for the EGR insufficient flow for the past few months. It comes and goes whenever it wants. Today Wifey called me and said something was wrong with the car, I drove it home (about 26 miles). The car runs fine as shifts through the gears, but as soon as it gets a load put on it, it cant pull hard like it used to and it gets a high pitched/squealy whistle similar to a turbo that's spooled up.
Its hard to say where its coming from but from what I can tell I'd say somewhere under the hood near the glove box. (that's the only way I can think of to describe it). There's a big long hill right outside her work that I wasn't sure I was gonna make it up. Car just didn't have any power and couldn't decide what gear to be in as RPMs were too high in a lower gear but wouldn't pull in the higher gear. Car pulls hard off the bottom but falls flat in the midrange. I was thinking maybe clogged cat but what would the whistling sound be?
I have a 2009 Ford Escape Limited with 3.0L. When Idling the Battery Light will turn on and stay on and when driving above 45Mph the light will turn off and then turn back on several miles down the road. After taking the car to Autozone and having the Alternator and Battery checked, I was told that the Voltage Regulator was bad and that I had to replace the Alternator due to the Voltage Regulator is not a serviceable part. After replacing the Alternator the battery and charging system is reading 13.86v (steadily) and when idling for about 5 minutes the Battery Light will come back on. I drive about 200 miles daily and do not want to get stranded... What else could be the problem?
View 6 Replies2003 Escape 2.0L ... I occasionally hear a single "pop" sound when I turn left. It seems to be coming from the area of the right rear wheel. Any obvious candidates for this issue?
View 2 Replies