Ford Escape / Hybrid :: 2009 - 4wd Will Not Work On 6cyl AWD
Jan 26, 2014
My wife has a 2009 Ford Escape limited with the six and awd. Lately with all the snow we have had we have found that the 4wd will not engage. I don't hear any clunking noise coming from a possible axle failure or the PTU grinding. Just how does the AWD work on these newer escapes. When does it know to engage? My mother in law's 01 is very trustworthy and keeps plowing the roads while our 09 sits at the road parked. With the surprise snow fall we got today my only alternative was to fire up the Duramax and pull it up our driveway to the street. Something that I can do in the driveway? I'm in hopes that I hay have overlooked something.
View 5 Replies
Advertisement
Drivers side turn signal does not work, and blinks fast when turned on. The brake light on that side and hazards do not work. when I unlock the car with the remote, it lights up fine.
View 5 Replies
I recently got an Escape and I am having a issue with the cruise control. That being, it doesn't work. The control module under the hood is all hooked up, the linkage the the throttle body and all. No broken cables.
The brake lights work as intended, and only when the brake is applied. On the inside, the dash-light cruise indicator works fine.
I ran the diagnostic by holding the off button and turning the key on. The cruise light flashes and I begin the sequence. I noticed I was pushing the brake out of habit while running the first few tests. They all returned 2 flashes upon completion of the diagnostic. All other buttons were registered.
Now the strange part, when I took my foot off the brake and did the same test, the final result is three flashes of the cruise light. I understand these flashes represent a fault, and I am having a hard time as I cannot find one.
What do these results mean? I'm thinking the brake being applied gives a fault surrounding the fact that cruise is disabled when the brake is applied.
View 3 Replies
My ford escape tailgate switch stopped working, the glass worked fine and opened with the switch. I ruled out the fuse as both I believe work off the same fuse. I removed the back panel to access the mechanism and found that, I could get the tailgate to work if I disconnected the wire from the glass tailgate switch and as the wire connector (shown In picture) was reinserted it would energize the tailgate switch and I am able to open the tailgate. What the actual problem is. I initially thought that it could be the tailgate switch itself but having seen what is happening I really am at a loss to what is the problem....
View 1 Replies
I can't find the fuse from the manual. Is it under another name?
View 8 Replies
My front interior light/map lights combination does not come on when the doors open. The rear seat and cargo area lights work when the doors open. Do the front interior lights are not designed to work in conjunction with the other lights when the door is opened?
View 6 Replies
I have a 2009 Escape, 2.5l engine and manual 5 speed transmission, 205,000 miles. It has has an intermittent miss that has been getting gradually worse over the past 3 months or so. I've been seriously futzing with it for the past 2 months, so far no luck. Definitely worse when it's cold. Not noticeable at all in gears 1-3 (even when cold), noticeable in 4th, mostly between ~2000-2500 RPM, and pretty bad when cold in 5th in the same RPM range, still noticeable when warm. No service engine light until today (#1 misfire).
If I let the vehicle idle for 10 minutes or so, the miss is much less noticeable. Replaced the plugs, absolutely no difference. Bought one COP and cycled through all cylinders, no difference. Finally broke down and took it to the Ford dealership where I bought it new and had them do a power balance test, which isolated it to cylinder #1. Swapped the #1 and #2 injectors and took it back to Ford, still showing cylinder #1. Did a compression test, #1 and #2 both around 165lbs, #3 and #4 both around 185lbs.
I'm a electrical engineer, so I spent some quality time with an oscilloscope to compare the drive waveforms of the #1 and #2 cylinder COP and injector...both COP and injector drive waveforms look identical when comparing to #2 cyl. Tried heating the PCM, made no difference (engine was cold, PCM was hot).
So it finally DID throw a code today, cylinder 1 misfire. I'm thinking I can almost hear a miss at idle now. And listening to the valvetrain at idle, there is unmistakably more valve noise coming from the #1 intake area than the other cylinders, but not terrible.
View 6 Replies
Where I should start looking for the root cause of the following leak? My wife noticed that when it was raining water dripped off the handhold by the front passenger seat. The ceiling liner is dry, no evidence of water soaking into it. I am thinking windshield or door seal as there is no moon roof and the liner is dry but before I start tearing into it I want to see if there is even a chance I can fix it myself.
View 3 Replies
I have a 2009 Escape that has developed a clunking noise in the right rear. On any bumpy roads it sounds like the shock tower lost it's top bushing but it could also be coming from somewhere lower. It also seems like the truck drifts to the right on bumpy left hand turns, kind of scary.
View 1 Replies
The facts: 2009 4x4 V6 Escape with Valve stem mounted TPMS
I am getting a tire pressure sensor malfunction fault. The warning light is on and the error message is displayed on the little screen in the gauge cluster.
What I have tried: First I should say I have replace to defective sensor twice now...
1) I put the escape in tpms train mode by hitting the hazard switch off/on about 6 times.
2) I used the train tool to train all the tires but there is one that is giving me trouble and will not train.
3) I tried deflating the problem tire and inflating it to the specified pressure given on the be pillar of the escape (30 psig)... after inflating it I tried to retain it with no luck.
4) I tried rotating the tires and as I mentioned earlier I have replaces the problem sensor twice. Still can't can't get the problem tire to train.
My thoughts:
1) I don't think this is a module error because I can train the other tires and since I rotated them I know their position is not a factor.
2) its possible that I have got two defective tpms sensors but I think that is unlikely.
3) I have read of another procedure to put the escape in tpms train mode that requires you to turn the ignition on/off, step on the break pedal, tap your head and rub your belly, etc... but I have not tried this method. Is there a difference from this train mode verse hitting the hazard switch on/off about 6 times?
4) Does the train tool only work on previously trained sensors? do I need to register the new TPMS sensor with the TPMS module? I have an OBDII tool that connects to scanXL software on my laptop which included the ford proprietary protocol. I looked for a way to program a tpms sensor (similar to how I did it with my toyota) but couldn't find the option.
View 4 Replies
I have a 2009 Ford Escape Limited with 3.0L. When Idling the Battery Light will turn on and stay on and when driving above 45Mph the light will turn off and then turn back on several miles down the road. After taking the car to Autozone and having the Alternator and Battery checked, I was told that the Voltage Regulator was bad and that I had to replace the Alternator due to the Voltage Regulator is not a serviceable part. After replacing the Alternator the battery and charging system is reading 13.86v (steadily) and when idling for about 5 minutes the Battery Light will come back on. I drive about 200 miles daily and do not want to get stranded... What else could be the problem?
View 6 Replies
I am pretty satisfied with the performance of my 2009 Ford Escape. Two years 51,000 miles after I find that the rear door does not open. Following threads of earlier Escape models I find how to remove the inside panel and open it manually. After a thorough study all I need is a replacement latch motor. The plastic latch cover has the following number GA6 GF30.
View 14 Replies
I have a 2009 Ford Escape XLT, 4 cyl. and in the summer I had the vehicle in as the speed sensor failed. Since that time I have an ongoing ticking sound (sounds like a diesel vehicle). I had the vehicle into my local dealer and after looking over the vehicle they stated that it was "normal". However, my warranty is up in January 2014 and this sound is horrible. Below is a video of the sound.
[URL] .....
View 14 Replies
My 2009 Ford Escape shift lever is stuck, not allowing me to shift out of park without using the manual override. However, when I slam my foot to the brake (rather than simply stepping on the brake), the brake switch relay, etc. all engage and I am able to shift out of park. Is this a brake switch relay problem, or is it possible that it has to do with the age of my brakes, etc?
View 3 Replies
Our escape recently started loosing its power steering, once the engine is shut off the power steering is ok. Also some times you can feel a pulsing in the steering wheel. I've been doing some googling and it looks like the dealers are replacing the steering columns to fix the problem.
My question : is this the only fix or if something like some contacts being cleaned or maybe replacing a steering sensor of some kind is the fix.
View 5 Replies
So I am changing my transmission fluid tomorrow and was wondering a few things.
1. I noticed some people pull off the transmission hose to the inlet and keep draining that until its clear. For a drain and fill do you do it like that or just pull the plug and refill?
2. When youre filling it back up you just measure how much you taken out and then fill the rest by the dipstick? Anything else i should know?
3. Since I havent changed my transmission fluid in 60,000 miles. I wanted to do a drain and fill. I was thinking I needed to drain and fill it 3 time to catch up to maintenance. How often would you do it to get it clear? Drain and fill then drive it for a week then drain and fill? Or do it all in one day?
View 4 Replies
Background: No A/C. Identified Clutch had completely failed. I replaced the clutch.
Status: I turned on the A/C and I saw the clutch come on...it was on for maybe 60s. During that time, the vents started to get cold! After 60s it never came on again.
Troubleshooting: I have refrigeration gauges but not much idea how to read the result. I hooked them up and noted about 350psi for the HP side, and about 100psi for the LP side. I think this tells me I should have enough charge in the system to cycle the compressor.
At this point I don't want to start random troubleshooting as I don't want to touch the refrigerant loop more than necessary. A few questions:
1) The HPCO switch, I was reading that it's mounted on a Shrader valve. Is this the case? I'd like to remove it and test at which point it switches. I have not tried bypassing it.
2) Do our vehicles have a temperature sensor near the evaporator? If so, whereabouts is it located?
View 10 Replies
My 2006 Escape Hybrid with <3500 miles on it had the ABS and 4X4 lights light today when I am 60 miles from home. I had this happen a few years ago, and I replaced a cracked tone ring, driving it to the dealer, who was only 5 miles away. My question is, is it safe to drive home and take it to my dealer who is 60 miles away, or should I have it towed?
The vehicle runs, in fact, the ABS and 4x4 light went out - in fact, I think I saw an indicator message that said 4x4 restored, but I am not sure, it appeared and then was replaced by X miles to empty. I would prefer to go home and take it to the dealer I purchased it from, but I don't want to drive in a car where the brakes may not work. I've read differing accounts on the internet and I can't figure if this is a "service soon" meaning I can make the trip home, or if it will strand me or worse if the brakes will fail on the trip home.
View 14 Replies
I just bought a 2010 Escape XLT 4 cyl. The mpg is showing to be 16.7, which is really low compared to what it's supposed to be. I bought it off of a car lot and it had been discounted so I'm guessing it was sitting there for a while before it was sold. Do you think that would cause the mpg to be low? I've driven it on the highway and around town. I've had it for 2 days, but it's freaking me out thinking that there is something wrong with it.
View 4 Replies
Get a set of real gauges if you want to do diagnostics. 110 psi on the low side indicates that the system isn't running at the time and that the underhood temp is around 100 F.
View 1 Replies
Ok, so I've got a little of an odd issue. It seems that no matter what I do, the AC is always active. Today I reverse flushed the heater core in my 02 Escape, and verified all hoses were clear. I replaced the thermostat housing (other thread) along with a new thermostat.
But, when I run the car, even with the heat full up and the selector set to the defroster and floor, the ac still blows ICE cold. It seems like it is still engaged no matter what. Winter is coming and I dont want my daughter to freeze (her truck).
View 2 Replies
