Ford Escape / Hybrid :: 2008 - Extended Crank Only When Cold
Mar 6, 2014
Trouble starting our 2008 escape after she has been sitting for atleast 4-5 hours (or more) We can get it going usually but we have to attempt several times before it 'catches'. After running and turning off, it starts no problem. Have replaced mas and didn't work. No 'check engine soon light' so just trying to narrow down the problem. Have replaced the fuel filter and all the spark plugs. Love my escape but not when it doesn't start!!
View 9 Replies
Advertisement
For a long time I have been noticing extended cold cranks as compared to my dad's truck which has 50k less miles. Hasn't been much of a big deal until lately the crank has been getting longer to the point where it is noticeable and bothers me.
When the truck finally fires (10-15 seconds) it will sit and idle no problem, maybe a little rough, but that's about it. It will also run a little rough if you start driving it right away but will smooth out fairly quickly. When it first starts it is usually accompanied by a small puff of white smoke.
As a quick run down it has had the injector o-rings, glow plugs and UVCHs replaced about 36k ago. I can verify it isn't the glow plugs or the harness because it would start reliably down to -25 without being plugged in.
My thought is the injectors are just nearing the end of their useful lives (248k). Does this make sense?
View 14 Replies
My outback started giving me intermittent extended crank starting problems on cold engine starts a few months ago. I brought it in first to repair shop and then dealership. Battery replaced, all systems checked out, computer update, camshaft sensor shim, and still I have the problem. What this could be?
View 19 Replies
I have a 2005 3.0 front wheel drive Escape that the kids normally drive and recently had a crank over/ no start condition in my driveway. I replaced the fuel pump about three months ago. Turned the key and couldn't hear the fuel pump so I proceeded to check the fuses and relays and everything seemed good. I also checked the inertia switch and it seemed ok as well.
I then checked for power at the harness right above the fuel tank and I had 12 volts on two of the four wires so I assume that I have power to my pump. I then took out the pump and had it replaced it under warranty. So I proceeded to install the new pump and I thought that I would hook the harness back up and just turn on the key for a second to be sure that the new pump is working and there was nothing to be heard. Looking for a wiring diagram/colors of the fuel pump?
View 2 Replies
I have a 2005 Escape with about 95k miles that won't crank after sitting in the sun on a very warm day. It's intermittent and might be OK for weeks.
This isn't when the engine is hot - it's when the air temperature is in the 80's+ and the black car is parked in the sun. This is the 1st warm weather we've had in several weeks and right on que, it didn't start this afternoon.
The battery is good and there is not voltage to the solenoid when cranking. I've used 2 sets of keys and replaced the PAT sensor ring hoping it was something anti-theft related.
Today, I switched out each under-hood relay (moved them to other locations) and still nada. Luckily today it's DOA in my driveway but may start later.
View 14 Replies
My wife has a 2010 Ford Escape. When we try to start it you have to push the key in REAL hard to get it to crank. It's been doing this for a while and seems to be getting worse. It took her 10 minutes before she could get it to crank earlier today. Our mechanic couldn't find anything wrong the first time we went in.
View 3 Replies
I have a 2003 Ford Escape Limited V6 replaced thermostat and fuel pump and 3 coils and 3 spark plugs recently. Now the theft light has come on and will not crank or start. The fuel pump is still not working unless I manually press the fuse under the hood which is also the only way the car will crank still will not start. That's because the previous owner got the key stuck in the ignition so he bypassed it with a dial you can turn. The dial will put the car into ACC and on mode but will not get the car to crank. Also btn1 and btn2 fuses under the hood are draining my battery.
View 3 Replies
About a block and a half from the house, it died while driving. Had heard some noise coming from rear drivers side maybe 20 minutes prior, and assumed it was the fuel pump.
So, I have put a new fuel pump, filter, and relay. Will crank, but not turn over. Next step was carburetor fluid in throttle while starting, still wouldn't turn over.
2001 Escape 6 cyl...
View 5 Replies
I have a 2007 XLS, 2.3L Auto/AWD. About a month ago it quit running while driving, just shut off. When I tried to restart the dash made clicking noises, fuel pump grunt type noises, cluster stays in drive position even though floor shifter indicates I'm in park. Pulled a code P0606, replaced PCM. It started and ran for 20 minutes, made it about 1/4 mile up the road, shut off again. Now I can't pull a code, dash indicates I'm in drive while vehicle is in park, same noises etc.
View 6 Replies
Ok, so I've got a little of an odd issue. It seems that no matter what I do, the AC is always active. Today I reverse flushed the heater core in my 02 Escape, and verified all hoses were clear. I replaced the thermostat housing (other thread) along with a new thermostat.
But, when I run the car, even with the heat full up and the selector set to the defroster and floor, the ac still blows ICE cold. It seems like it is still engaged no matter what. Winter is coming and I dont want my daughter to freeze (her truck).
View 2 Replies
I have a 2001 Escape, V6 engine and I guess it really does not like it when it's cold outside. Usually the car runs just perfect but when the winter arrives and temps drop into the 20s the truck does not want to run idle right when I first start it. I have tried by stating it without touching the gas pedal. And also by pushing it all the way down and then releasing it. I don't know which method is the right one, but it doesn't seem to make a difference. It takes some time and eventually after about 5 miles of driving it will act normal again. What could I do to fix that?
View 9 Replies
My 12 Escape with the 3.0, shifts fine in warm weather or in cold weather when warmed up. But first thing on a cold morning she's a bit of a screamer getting into the next gear. Is this a signal of something about to go wrong? Is there an easy adjustment? Or this is the way of it and it is fine......
View 14 Replies
I have a 2001 Ford Escape. When started cold, it revs up to abt 3000 rpm. Slowly drops back to about 1000 in abt 10 secs. When the engine is hot, it often wants to idle 2500+ rpms and I have to really step on the brakes to slow the vehicle. When I disconnect the IAC the engine dies. When it is revving high, I can disconnect and reconnect the IAC quickly, and the idle will drop back down for a few minutes, until I step on the accelerator, then start climbing again. It seems to be a lot worse when hot.
I replaced the IAC and TPS about 20k miles ago and thought it was fixed, but the problem has returned. At that time, I could tap on the IAC and it would "get well" for a while. Tapping on this one doesn't seem to change anything. No CEL, engine runs smooth, and I don't notice any air leaks (none that I've found, at least).
View 8 Replies
I'm needing cold engine misfire. 2001 escape 3.0 engine 190300 miles on it. I changed the plugs, cleaned the fuel injectors, new air filter, new fuel filter, cleaned the pcv valve and new ideal control valve. When the engine is cold it starts right up but wont idle right and misfires sputters some to but run the rpm's up and it smooths out. drop to idle and it misses. Now when the engine gets to operating temp it seems to run fine. What am I overlooking to find the problem?
View 5 Replies
2 questions regarding my 2005 Mariner 3.0L, as follows:
1. After a cold start (in the garage, so not freezing cold) the water pump belt - not the serpentine belt - squeaks for 15 - 20 seconds; ambient temperature doesn't matter. I had put a new belt on about a year ago, then this began 6 or so months later. Thinking I may have a defective belt, I replaced it again about 3 months ago, but the squeaking has continued - starting immediately after the replacement. My analysis is that the water pump bearing is going south. I've noticed that it is taking a little longer for the squeak to go away in the past few weeks, so it's probably getting worse, altho no leaks at this point. So the question is, so any other reason this is happening?
2. Assuming I do need to replace the WP, I bought a new one from the local parts house. I have a shop manual for the car, which tells me to remove the thermostat housing, hose connection to the WP, etc., and then remove the WP by removing just 3 bolts. However, the replacement part is just the front of the housing with the impeller and pulley included, so there are a half-dozen or so bolts that hold this new part onto the WP housing. So, doing this change-out? Will the front of the WP housing come off by itself without disconnecting the hose, etc., or do I first have to remove the whole WP and then take it apart to replace the impeller and front cover? I can't really tell from the pic in the shop manual, and it doesn't address dis-assembly of the WP.
Also, I'd like to just remove the belt w/o cutting it and having to buy a new one. Can I do this by just loosening the WP bolts? (I know how to re-install, obviously.)
View 6 Replies
I recently purchased a 2008 ford escape, v6, 2wd. When I bought it, I noticed the ABS light was on, and I got an appointment scheduled to get it fixed, but they couldn't get it looked at for 2 weeks out. Needing a vehicle to drive to and from work, I agreed to schedule the appointment, as I test drove it with the light on with no issues.
Well, after putting about 200 miles on it over the weekend, there are now noticeable issues. First off, the parking brake light decided to come on intermittently, and now it comes on and off spiradicly. Secondly, when I drive the car now, I can hear a clunking noise, followed by the traction control light blinking (It was on constant before), and loss of power. I ended up pinpointing that to being the brakes engaging while the car was driving (I noticed when I stopped, the rotors were really hot. I threw a tiny bit of snow on them and they smoked really bad.
I removed the tires in the front, and checked the tone rings, they both appear to have been replaced recently as they are still shiny as if they were brand new. I also took the ABS sensors out, and wiped them down, they also appear to be new (Although the bolts that hold them on clearly aren't new). I don't have access to a high-level scan tool to get it looked at, and I refuse to drive it anymore to take it to a shop just to have it looked at, what else could be causing the issues? It's highly possible that one of the ABS sensors is bad, but how do I go about checking it without just replacing it? Can I use a voltmeter or something to check it to see if it's getting the correct voltage?
I am not sure how the abs system works, but I know that the traction control light is on because the abs light is on, as they both have the same systems they use, but would that also cause the parking brake light to come on, too ? It originally wasn't on, but just started doing it recently. I checked the fluid level, and it's more than within range. This is my daily driver, and obviously I can't go two weeks without a vehicle, and that's the soonest I can get it into a shop...
View 6 Replies
OK so this issue first started in July on way back from Florida the brakes started going to the floor. You did have normal braking power, but you had to about stand on them. Took it to mechanic who cleaned and adjusted brakes, after that they seemed to work fine. Fast forward to a month later, I was going over some train tracks with a somewhat heavy load, I braked when going over them, right after that it seemed the brakes went about half way before braking. I took it back to same mechanic who said it's now either the Master Cylinder, or ABS module. I have found so many conflicting posts on this I'm not sure which way to go. I'd really hate to spend $400 on MC, and then it turns out to be ABS. There is also a swooshing noise when you depress brake.
View 11 Replies
My wife drives a 2008 V6, where is the PCV Valve? Pics ????
View 7 Replies
My 08 escape (3.0) wouldn't go over 45-50mph Sunday on my way home. The next morning I made it about 2 blocks and the battery light came on and it died. I am replacing the battery tomorrow because it tested bad but believe there is also an exhaust problem. Last week it began making a noise I could hear inside the car only when accelerating. Almost sounded like a small,air plane. The car will start and run now but cuts out and sometimes will Rev up when I press accelerator and sometimes won't. The exhaust pipe gets hot really fast and it and the motor both vibrate we the car is started (more than normal) any clue on where to start??
View 1 Replies
I got a 2001 Escape XLT (V6) a couple of months ago. Its in great condition, only 82k miles on it too. It had the notorious door handle issues which I have had fixed. It also had the wet weather stuttering problem, which I had fixed by having all 6 spark plugs replaced (Motorcraft OEM plugs), the back 3 coils replaced, upper intake gaskets replaced, Valve cover gasket replaced, PCV valve replaced (motorcraft).
It runs great when its warm, the problem I am having is when its cold outside and the engine is cold, it starts up fine but idles like crap and if its really cold outside, it starts and dies 3 or 4 times before it can even get to the crappy, stuttering idle. I have to intermittently feed it gas to keep the cold idle going long enough (3 or 4 minutes) before I can drive it. Once the engine is warm it drives like a champ. The only warm engine issue, is occasionally after driving it and putting it in park, the engine will rev up to 2000, 3000+ rpms, and just keep going up until I shut the engine off.
The codes read P0171 and P0174, which are lean on bank 1 and bank 2. It had also thrown a misfire on cyl 6 but once I cleared that it hasn't come back, just the lean codes are still present.
From what Ive been reading, this can be a number of issues, ranging from the IAC valve, EGR valve, MAF or the lower intake gaskets. I'm very much a rookie when it comes to car mechanics, but I think I can handle changing the IAC, EGR and MAF since they are all on top of the engine. However I don't know if I could handle the lower intake gaskets. Ironically, the gaskets are the cheapest part, but the most labor if I paid someone else to do it.
If I replace the EGR, do I also need to replace the EGR Modulator as well? Looking for brand names that are best bang for the buck when it comes to these other parts I have mentioned?
View 14 Replies
Wife is operating a 08 Escape with about 31K miles on her. She loves the vehicle but since we bought it with 24K miles on it it has had a rattle under it. I assumed that it was the heat shield and i would get around to securing it but haven't yet. Here's the question. I noticed recently that about mid way back under the pass side there is a black spot developing on the concrete where she parks every day. The vehicle does not sit and idle there. Its started and is moving in about 20 every time. I have not got under there yet but was looking for possible answers as to what and where to look? Flex pipe? Bad seal on exhaust? If this is the case should a 31K mile vehicle have this issue? The vehicle is louder than a 2.3L should be but from reading that seems normal. If it is the flex is this something that a novice wrench can do?
View 6 Replies
