Ford Escape / Hybrid :: 2008 4WD 2.3L - Rattling / Exhaust Leak?
Mar 25, 2014
Wife is operating a 08 Escape with about 31K miles on her. She loves the vehicle but since we bought it with 24K miles on it it has had a rattle under it. I assumed that it was the heat shield and i would get around to securing it but haven't yet. Here's the question. I noticed recently that about mid way back under the pass side there is a black spot developing on the concrete where she parks every day. The vehicle does not sit and idle there. Its started and is moving in about 20 every time. I have not got under there yet but was looking for possible answers as to what and where to look? Flex pipe? Bad seal on exhaust? If this is the case should a 31K mile vehicle have this issue? The vehicle is louder than a 2.3L should be but from reading that seems normal. If it is the flex is this something that a novice wrench can do?
View 6 Replies
Advertisement
I was just changing the oil on my wifes 2008 Escape and noticed a oil leak. At first I thought it was an oil pan gasket,But its higher than that. Then I thought maybe an axle boot but it's also higher than that. It's on the passenger side about the middle of the engine right under neath the biggest pulley.
Its a cylinder shape mold coming off the engine about an inch long with a bolt on the end of it. I'm not seeing oil any higher than that and seems to be coming from there from what I can see. Is this something common with the Escapes?The truck has 55,650 miles on it and this is the first issue so far.The wifes first escape we traded for this was an 01 with 200,000.
View 4 Replies
2007 Escape XLT 3.0 AWD. During the winter there can be quite the exhaust smell in the interior upon startup and especially if using the remote start. During driving the smells will clear out and appear again with an extended stop but not as bad as initial cold startups. I realize the hotter the engine and exhaust components the smaller the leaks become. Hopefully not an exhaust manifold leak.
Looking for a way to find where a leak may happen. I saw a video of a garage using "smoke" pushed up the tailpipe to find leaks. Or any other techniques or similar situations.
View 2 Replies
Is there any condition that would make a Ford Escape have an intermittent exhaust leak that could come into the cab?
View 18 Replies
I have a 2004 Ford Escape 3.0 V6 FWD, and the air conditioning has been blowing only to defrost for a few weeks now. After many searches online, most sources seem to agree it is a vacuum leak, as the selector switch is vacuum driven if you want anything except defrost. I popped the hood and within one minute I found one open vacuum line that looks like it has been worn in two.
The line in question goes from the vacuum canister towards the passenger side of the firewall, then goes to a T connector, then a line (the one that is broken) continues towards the heater core lines to where the break in the line is. I found a picture online of what it should look like, but I am having trouble accessing the line that goes through the firewall and behind the glove compartment. I am pretty sure this vacuum line continues through the firewall between the two heater lines, but after that I am stumped.
I popped the glove box down out of the way and I see two thin vacuum lines and a small metal "can" nearby. The black line goes from a fitting and into the A/C bundle, and the white line goes from the top of the metal canister and down into the same bundle. My main question is which line controls the AC selector, and how do I pass a replacement line through that part of the firewall to make a good connection, as it seems the break is at the firewall itself with no extra sticking out for me to connect to.
View 3 Replies
I set out to do a coolant flush but ran into an increasing number of problems. When I went to replace the thermostat I discovered one of the three bolts would not come out due to the inside thread on the thermostat housing being stripped. I purchased a brand new housing and O-ring.
When I reinstalled the thermostat (also Motorcraft brand) with the above O-ring and attached all the hoses I had a severe leak between the thermostat housing and the intake hose connecter. I diagnosed the problem as the O-ring slipping off of the lip or ledge inside the thermostat housing and not sealing all the way around.
The Motorcraft O-ring seemed like the diameter was too big for the interior lip of the thermostat housing because the ring would pop up on one side whenever I tried to fully seat it on the interior lip. I went to AutoZone and purchased an orange Duralast O-ring, and while it seemed to be a little smaller diameter than the Motorcraft it too slipped off when I tightened down the housing.
I have tried everything, and every time I tightened down the housing I did it very slowly and carefully doing an 1/4 turn at a time with the three bolts but still the O-ring would slip off.
View 4 Replies
Vehicle: 2001 Escape 3.0L V6
I'm listing here the obvious that has been changed already:
1) Valve cover gaskets
2) Oil pan gasket
3) Timing chain cover gasket
4) Upper and lower manifold gaskets (not oil related but changed)
5) PCV valve
6) Washed engine twice to remove everything and make sure nothing else burning
Problem: I still have a small leak from the top that causes smoke near or around the #4 COP on passenger (left side of the motor). But we do see some oil coming from near the PCV valve. It makes no sense and after reading what caused smoke on that side of the vehicle I changed the Timing chain cover gasket (which were finished anyway) and while was at it the oil pan but to no avail. Smoke and leak still there.
Probably not: I know that it is not the head gasket because there is no sign at all; I've never lost a drop of coolant and there is no smoke from the exhaust in back.
Suspicion: Could it be the oil separator where the PCV valve connects and makes it's way around to the other side? Is there something I am overlooking? There can't be many other places for an oil leak like that.
Coincidence ? : Even after changing all the COPS and spark plugs I found oil in the #4. However smoke was there before. I thought maybe a cylinder gasket I got second opinion from my mechanic says no not cylinder...
Engine runs well except for misfire in #4 but comes and goes. I think when oil builds up.
View 5 Replies
My 2010 2.5L FWD Escape has oil on the steering boot and has run down on crossmember (?) It is equipped with Electric Power Steering. This appears to be coming from the rack and pinion but does it have fluid in it? How can you add if it does. I have 96,000 miles on the vehicle and except for a drivers door actuator and scratched drivers glass, this is only problem.
View 5 Replies
I have a 2003 Escape Limited 4WD with approx 163K on the clock. It developed a tranny leak from the front driver's side axle. The seal is new and in good shape as I just replaced the axle and seal a few weeks ago. (I checked the shaft size and surface finish of the axle and it is in spec.)
I just removed the axle tonight and discovered that the problem seems to be the bushing just inboard of the seal in the tranny. The axle has movement up and down when inserted. (Not good!) This is allowing the fluid to leak from the seal.
Here are my questions. Is this a simple DIY fix using a slide hammer type of puller (or similar), or is it time to take it to a tranny shop. I can not seem to find a replacement part listed anywhere.
Also, with this much mileage, should I have the tranny reworked as a precaution if this repair requires dis-assembly or should I just address the leak and think about dumping it? I would prefer to keep it as my kids are now driving age and this is primarily their vehicle. (It has been a great little truck!)
View 14 Replies
I recently purchased a 2008 ford escape, v6, 2wd. When I bought it, I noticed the ABS light was on, and I got an appointment scheduled to get it fixed, but they couldn't get it looked at for 2 weeks out. Needing a vehicle to drive to and from work, I agreed to schedule the appointment, as I test drove it with the light on with no issues.
Well, after putting about 200 miles on it over the weekend, there are now noticeable issues. First off, the parking brake light decided to come on intermittently, and now it comes on and off spiradicly. Secondly, when I drive the car now, I can hear a clunking noise, followed by the traction control light blinking (It was on constant before), and loss of power. I ended up pinpointing that to being the brakes engaging while the car was driving (I noticed when I stopped, the rotors were really hot. I threw a tiny bit of snow on them and they smoked really bad.
I removed the tires in the front, and checked the tone rings, they both appear to have been replaced recently as they are still shiny as if they were brand new. I also took the ABS sensors out, and wiped them down, they also appear to be new (Although the bolts that hold them on clearly aren't new). I don't have access to a high-level scan tool to get it looked at, and I refuse to drive it anymore to take it to a shop just to have it looked at, what else could be causing the issues? It's highly possible that one of the ABS sensors is bad, but how do I go about checking it without just replacing it? Can I use a voltmeter or something to check it to see if it's getting the correct voltage?
I am not sure how the abs system works, but I know that the traction control light is on because the abs light is on, as they both have the same systems they use, but would that also cause the parking brake light to come on, too ? It originally wasn't on, but just started doing it recently. I checked the fluid level, and it's more than within range. This is my daily driver, and obviously I can't go two weeks without a vehicle, and that's the soonest I can get it into a shop...
View 6 Replies
OK so this issue first started in July on way back from Florida the brakes started going to the floor. You did have normal braking power, but you had to about stand on them. Took it to mechanic who cleaned and adjusted brakes, after that they seemed to work fine. Fast forward to a month later, I was going over some train tracks with a somewhat heavy load, I braked when going over them, right after that it seemed the brakes went about half way before braking. I took it back to same mechanic who said it's now either the Master Cylinder, or ABS module. I have found so many conflicting posts on this I'm not sure which way to go. I'd really hate to spend $400 on MC, and then it turns out to be ABS. There is also a swooshing noise when you depress brake.
View 11 Replies
My wife drives a 2008 V6, where is the PCV Valve? Pics ????
View 7 Replies
My 08 escape (3.0) wouldn't go over 45-50mph Sunday on my way home. The next morning I made it about 2 blocks and the battery light came on and it died. I am replacing the battery tomorrow because it tested bad but believe there is also an exhaust problem. Last week it began making a noise I could hear inside the car only when accelerating. Almost sounded like a small,air plane. The car will start and run now but cuts out and sometimes will Rev up when I press accelerator and sometimes won't. The exhaust pipe gets hot really fast and it and the motor both vibrate we the car is started (more than normal) any clue on where to start??
View 1 Replies
My ford escape tailgate switch stopped working, the glass worked fine and opened with the switch. I ruled out the fuse as both I believe work off the same fuse. I removed the back panel to access the mechanism and found that, I could get the tailgate to work if I disconnected the wire from the glass tailgate switch and as the wire connector (shown In picture) was reinserted it would energize the tailgate switch and I am able to open the tailgate. What the actual problem is. I initially thought that it could be the tailgate switch itself but having seen what is happening I really am at a loss to what is the problem....
View 1 Replies
So I have a 2008 escape 4wd.... I am getting a few flat spots on the inside passenger rear tire... So I figured it was the shocks so I unbolted both and cycled them and they both felt the same... There was dampening you can feel the oil going through the valves or whatever... I have felt completely bad shocks before and it was just a smooth motion when cycling the shocks... Can it still feel like there good but there not? The thing has 85k on it and I'm not sure if they have ever been replaced before..
View 6 Replies
I have a 2008 Ford Escape XLS (4 cylinder) that currently is having an issue with the AC system. It blows the air at the correct temp but it only comes out of the primary vents. If i select defroster or floor vents, it doesn't switch over to those. What specifically should I be looking at to fix it.
View 8 Replies
Where can I find the key pad code on an 08 escape? I don't have the card in the glove box and I don't want to pay the dealer. It should be printed on the security module box. Where to find it? On my f250 it was under the dash behind radio.
View 14 Replies
I have a 2008 xlt with a 3.0. In the little over 2 years I've had it, most notably in the past year, I have replaced the front driver side ABS sensor 8 times. This is getting extremely cost, and outrageous. Every month or so, the ABS light comes on and the ABS starts locking up when I am driving it. Every time it does it, I have to take it back to the shop for diagnostics, at a rate of nearly 300 a pop. As you can see, the bill for this one damn sensor has become outrageous.
Every time, the same fault code comes up. Drivers front ABS sensor. Putting on a new sensor fixes it, every time, but only temporarily. I have had the tone ring replaced just to make sure that wasn't it, and every single time it's always been the sensor itself.
I have tried various brands, including a couple of OEM a pop to make sure it wasn't just lower quality parts, and I have the exact same result every time. I have noticed it seems to do it most notably during extremely wet conditions, or heavy snow, although a couple of the times it started acting up in the heat of summer. I have even attempted cleaning the abs sensor to make sure it wasn't just dirty, to no avail.
As I mentioned, only replacing the sensor makes the issue go away, and when I am driving the abs system engages at random times if I leave the light on for too long without fixing the abs light.
View 8 Replies
Trouble starting our 2008 escape after she has been sitting for atleast 4-5 hours (or more) We can get it going usually but we have to attempt several times before it 'catches'. After running and turning off, it starts no problem. Have replaced mas and didn't work. No 'check engine soon light' so just trying to narrow down the problem. Have replaced the fuel filter and all the spark plugs. Love my escape but not when it doesn't start!!
View 9 Replies
My 2008 Ford Escape is stuck at 5% Oil Life I have tried the reset procedure But when I press the 3 buttons Setup Info or Reset nothing changes It will not change screens When I start my car I see the KM (I'm from Canada) then within a couple of minutes it shows %5 Oil Life and no matter what I do it wont change or scroll to a different screen. When the door is ajar or tail gate open it shows but then will flash back to the 5% Oil Life
View 8 Replies
2008 Escape V6
Got the oil changed at Walmart and they told us there was oil in the air filter and we should replace the pcv valve. Before we changed it the oil pressure light had started coming on when the car is stopped, either in gear or park. Once the gas is hit it goes off, even at something like 1 mph. Well I changed the pcv valve but the oil pressure light is still doing the same thing. What should be my next step?
View 2 Replies
