Ford Escape / Hybrid :: 2007 V6 - Mystery Rattle In Crankshaft Area When Idling
Nov 19, 2012
2007 Ford Escape XLT V6, ~60K miles .... My wife has this rattle in her escape, has had it about a month now. The rattle happens when idling, is less noticeable when driving the car, but might just be drowned out by road noise, etc. Revving the engine in neutral doesn't seem to affect the rattle at all as far as I can tell.
I listened around the engine compartment with a stethoscope for awhile and couldn't pinpoint anything so I told her to bring it in and have it looked at. She brought it in to "Brake King", they do full service mechanic work, but i'm not sure how great they are, but they are flexible about bringing the car in and looking at it right away and my wife can't be without her car for very long since she uses it for work. They said it need the sway bar rods and bushings replaced (they did this and the noise didn't go away). I was pretty suspect about it since the rattle happens when idling, but i'm no expert so I figured they knew what they were doing.
We brought it back and the guy said that the noise was internal to the engine and asked about where we get the oil done. (I do the oil myself and always use Mobil 1, I really don't think it is an oil issue. Maybe the oil filter since we don't change that every time, but again... They did a free synthetic oil change + filter change and that didn't work.
All the while i've been doing research and I decided to go ahead and remove the drive belt to see if the noise would go away when I did ( this whole time I was suspecting something on the drive belt). So I removed it and the noise did go away for the minute or so I ran it without the belt. This pretty much confirmed to me that it was something on the drive belt. I replaced the tensioner since I read that that could be a suspect and they are "relatively" cheap and easy to do. That did NOT work. (I also broke the bolt that holds it on and had a helluva time trying to find a replacement, but that is a whole other story).
So while I had the splash guard off, I listened some more. The rattle really seems to me to be coming from the crankshaft pully area rather than from the A/C compressor area or the alternator area. If it was the C/S pulley, wouldn't it still make the rattle even with the belt off? Looking in the Haynes manual, the C/S pulley doesn't necessarily look like that easy of a replacement (especially if I'm not sure it will actually fix the problem). Anyny opinions as to whether that might be the problem, and if so if a DIYer can do the replacement?
Here is the video. When watching it live, I swear I see a bit of a wobble on the pulley compared to the other pulleys on the belt line, but in the video, you can't really see it...
Video : Mystery rattle ford escape 2007 - YouTube
View 5 Replies
Advertisement
Vehicle: 2001 Escape 3.0L V6
I'm listing here the obvious that has been changed already:
1) Valve cover gaskets
2) Oil pan gasket
3) Timing chain cover gasket
4) Upper and lower manifold gaskets (not oil related but changed)
5) PCV valve
6) Washed engine twice to remove everything and make sure nothing else burning
Problem: I still have a small leak from the top that causes smoke near or around the #4 COP on passenger (left side of the motor). But we do see some oil coming from near the PCV valve. It makes no sense and after reading what caused smoke on that side of the vehicle I changed the Timing chain cover gasket (which were finished anyway) and while was at it the oil pan but to no avail. Smoke and leak still there.
Probably not: I know that it is not the head gasket because there is no sign at all; I've never lost a drop of coolant and there is no smoke from the exhaust in back.
Suspicion: Could it be the oil separator where the PCV valve connects and makes it's way around to the other side? Is there something I am overlooking? There can't be many other places for an oil leak like that.
Coincidence ? : Even after changing all the COPS and spark plugs I found oil in the #4. However smoke was there before. I thought maybe a cylinder gasket I got second opinion from my mechanic says no not cylinder...
Engine runs well except for misfire in #4 but comes and goes. I think when oil builds up.
View 5 Replies
Getting a fuel smell especially when 2004 3.0 escape is idling. Is there a replaceable evap filter or maybe the pcv valve?
View 3 Replies
I have a 2001 Ford Escape 3.0 4WD, it has a rattle in the motor and no acceleration... Bought the escape with the rattle when you start it up and put into drive it wont accelerate. Transmission is good...
View 3 Replies
So my wife was driving our '10 escape xlt and the engine light came on and it displayed the 'check engine' message on the screen. It has 86500 miles and luckily no problems yet. The only thing that has changed was she accidentally put super premium gas in it the other day. The light came on and after she drove it home (about 10-12 miles) and it sat for a few hours and i drove it about 20 miles it randomly went off while it was idling.
I shut it off and let it sit for 20 minutes and then let it idle for a few and it never came back. It has been running ok. We definitely drive it a lot as she works day shift and i work nights. I'm just trying to make sure there's nothing wrong with it. I got a bulletin a while back about the intake getting moisture in it. I didn't know if maybe this could be the beginning of this or something else. This is a whole new territory for me as i consider my 91 f250 'new'
View 6 Replies
2004 Escape 2wd 6 cylinder 170k miles. Intermittent clunk/rattle sound when hitting bumps while going straight and especially turning right. I felt a slight bumping in passenger side floor board. Inspected everything. All looks good and tight- no signs of loose hardware, worn ball joints or tie rods. Only thing I noticed was a slight rub mark (missing paint) on the lower control arm under the sway bar on drivers side. And noticed the rear bushings on the control arms are tearing.
Not collapsing but with the tire removed and suspension hanging at full droop you can see tears in that rear bushing on both sides. We painted the arm and sway bar in the rubbing location to see if it makes a mark there again after driving it a few days. Question is do you think that the rear control arm bushings could be allowing enough movement to contact the sway bar or make the noise? The bolts are tight. Has newer Moog struts and newer swaybar end bushings, possibly sway bar hold down bushings too- (they look pretty good).
View 1 Replies
we have a 07 Escape that the brake lights stay on even with the ignition key off. I changed the brake switch twice. Thinking maybe the first may be faulty from the factory. I'm stuck on what the problem could be
View 8 Replies
I have a 2007 Mercury Mariner with a 3.0 Liter V6 engine AWD. The transmission is giving me a problem. No shift into 2nd and 4th. Solenoid or band broken I think. Is the bolt hole pattern to attach the tranny to the engine different between the 3.0 V6 and the 2.3 I4?
View 3 Replies
I have a 2007 XLS, 2.3L Auto/AWD. About a month ago it quit running while driving, just shut off. When I tried to restart the dash made clicking noises, fuel pump grunt type noises, cluster stays in drive position even though floor shifter indicates I'm in park. Pulled a code P0606, replaced PCM. It started and ran for 20 minutes, made it about 1/4 mile up the road, shut off again. Now I can't pull a code, dash indicates I'm in drive while vehicle is in park, same noises etc.
View 6 Replies
When started very high idle after hitting gas pedal sometimes it will lower idle sometimes not,,then holding pressure on gas pedal it has very bad surging ... Any guesses what might be and possible cost fix?? I am no mechanic,will have to take it somewhere...90,000 miles on it..
View 3 Replies
I have a 2007 Ford Escape with a passenger side low beam that won't turn on when the headlights are turned on. I have replaced both low beam lights and checked all the fuses. Fuses are ok,none are burned out. My high beams work perfectly as well as my fog lamps. I need any and all advice and information , including any simple wiring diagrams that could be of use . Is it possible that the multi function switch for the turn lights and headlights is the problem?.
View 10 Replies
Recently picked up a 2007 Escape with 108,000 miles. The vehicle is in great condition with a full service history. Recently I've noticed a bit of shimmy in the steering wheel and noise from the front drivers side wheel accompanying the shimmy.
At speeds of 50mph+ the shimmy will start. When going straight there is not much of an issue but when a gradual right hand turn on the highway the shimmy starts. Back to straight and it goes away. Not really noticeable on left hand curves.
Steering issue?
Tie Rods?
Bearings?
I'm going to dig into it to get it fixed.
View 1 Replies
I own a 2012 Camry Hybrid XLE, but I'd imagine this issue could exist w/ any trim. Hear a slight crinkle/rattle from time to time coming from your headliner area? At times it almost sounds like someone padded your headliner with a plastic grocery bag.
I usually heard it on bumpy roads. I went through a nightmare with my dealer where they had my car for about 40 days trying to figure out the cause. They even replaced the headliner! (they did a lousy job too, w/ lots of oil smudges and scratches on my plastics)
Discovered the real cause of rattle. The sound actually comes from where the sun visor meets the headliner. The white plastic socket (pictured) where the sun visor plugs in has some wiggle room. When the car vibrates (be it from a bumpy road or what have you) it can slide against the interior cut out of the headliner. This makes an obnoxious crinkling sound.
At the moment I'm driving around with no sun visor on the passenger side-- and I also have no rattle (occasionally I might hear it from the driver side sun visor, but it's minor). I'll probably add some foam up there to add some more tension to alleviate the issue completely. Even just re-seating the sun visor and ensuring the screws are tight would probably have significant impact...
View 2 Replies
The alternator light on my 2001 Ford Escape 3.0L comes on intermittently. I've replace the alternator, belt, tensioner, and battery. I've check the wiring and the ground and there are no noticeable issues. When I first start up it never comes on. After about 30-40 minutes of driving it will start to come on intermittently. I've noticed that it always shuts off when taking off from a stop. I have the most trouble with it coming on while driving around the city and little trouble while cruising on the highway. I'm completely stumped. Is it possible for one of the other pulleys to be causing this if for instance some bearings were going bad and it was binding up or problems with the crankshaft slowing down the belt?
View 13 Replies
I've not long had my 2007 SF but I noticed that the tailgate area is not as quiet as it should be. There is a definite thump over typical poorly repaired roads in the UK, but there is also a rattle. I thought one culprit might have been the spare wheel since there is a spring which allows some movement. My main focus is the tailgate I was wondering if anything can be adjusted to keep it still.
View 7 Replies
So I am changing my transmission fluid tomorrow and was wondering a few things.
1. I noticed some people pull off the transmission hose to the inlet and keep draining that until its clear. For a drain and fill do you do it like that or just pull the plug and refill?
2. When youre filling it back up you just measure how much you taken out and then fill the rest by the dipstick? Anything else i should know?
3. Since I havent changed my transmission fluid in 60,000 miles. I wanted to do a drain and fill. I was thinking I needed to drain and fill it 3 time to catch up to maintenance. How often would you do it to get it clear? Drain and fill then drive it for a week then drain and fill? Or do it all in one day?
View 4 Replies
Some customers may experience a buzz or slight rattle noise from the rear portion of the headliner when the vehicle hits small sharp bumps. It has been determined that the source of such a rattle may be the Tire Pressure Warning System (TPWS) antenna located above the headliner between the rear of the sliding roof opening and the top of the back glass.
Well, after a few months of frustration hearing a buzzing in the back seats, i notice this bulletin on the 07 ES and I've tested on my 08 car and it is the same, simply tapping on the roof liner or pulling it and releasing it makes a buzzing sound. Even when i tap on the glass roof, the buzzing sound is resonating. Would the dealer rectify this issue if my car is a 08 ? I'm still under warranty.
View 9 Replies
Have a 1992 5.7 litre silverado with a screeching noise from the crankshaft pulley when engine is warm and idling. Noise goes away when engine is accelerated. Noise remains on crank pulley when serpentine belt is off pulleys. Did replace tensioner pulley, alternator, and idler pulley. No noise noted when started cold. Serpentine belt is only weeks old no signs of damage. No rough idle or performance changes noted just a annoying noise similar to a turbo but only when no torque is applied.
View 1 Replies
Background: No A/C. Identified Clutch had completely failed. I replaced the clutch.
Status: I turned on the A/C and I saw the clutch come on...it was on for maybe 60s. During that time, the vents started to get cold! After 60s it never came on again.
Troubleshooting: I have refrigeration gauges but not much idea how to read the result. I hooked them up and noted about 350psi for the HP side, and about 100psi for the LP side. I think this tells me I should have enough charge in the system to cycle the compressor.
At this point I don't want to start random troubleshooting as I don't want to touch the refrigerant loop more than necessary. A few questions:
1) The HPCO switch, I was reading that it's mounted on a Shrader valve. Is this the case? I'd like to remove it and test at which point it switches. I have not tried bypassing it.
2) Do our vehicles have a temperature sensor near the evaporator? If so, whereabouts is it located?
View 10 Replies
My 2006 Escape Hybrid with <3500 miles on it had the ABS and 4X4 lights light today when I am 60 miles from home. I had this happen a few years ago, and I replaced a cracked tone ring, driving it to the dealer, who was only 5 miles away. My question is, is it safe to drive home and take it to my dealer who is 60 miles away, or should I have it towed?
The vehicle runs, in fact, the ABS and 4x4 light went out - in fact, I think I saw an indicator message that said 4x4 restored, but I am not sure, it appeared and then was replaced by X miles to empty. I would prefer to go home and take it to the dealer I purchased it from, but I don't want to drive in a car where the brakes may not work. I've read differing accounts on the internet and I can't figure if this is a "service soon" meaning I can make the trip home, or if it will strand me or worse if the brakes will fail on the trip home.
View 14 Replies
I just bought a 2010 Escape XLT 4 cyl. The mpg is showing to be 16.7, which is really low compared to what it's supposed to be. I bought it off of a car lot and it had been discounted so I'm guessing it was sitting there for a while before it was sold. Do you think that would cause the mpg to be low? I've driven it on the highway and around town. I've had it for 2 days, but it's freaking me out thinking that there is something wrong with it.
View 4 Replies