My friends 2006 Escape has the ( low pressure warning light) flashing on for about 10 seconds after starting the engine. All tires are at correct pressure. What is causing this?
View 5 RepliesI have a 2006 Ford Escape that's turning into a mystery. Over the last few months the warning lights have been reporting issues with the overdrive. I've taken it to the mechanic who hasn't been able to identify the issue.
He's cleared the issues from the ECU, and the car doesn't complain for about 2 weeks, then it reports a different issue related to the overdrive (eg: OD or transmission).
Possibly related, the car occasionally loses power on acceleration. When taking off from a stop, it'll be really underpowered while getting up to speed. This only happens occasionally.
Is it a part failure, or could it be electrical or related to the sensors?
My "Theft" light on my 2005 Ford Escape is flashing and I cannot start the Escape.
1. I tried the key that I had been using successfully for the last 7 years. , car did not start, Theft light blinked. ,
2. Tried wife's dealer key, Car won't start, theft light blinks.
3. Tried various things, such as manual locking & unlocking, turning alarm beeping on/off, disconnecting battery, etc. Nothing works.
Called the dealer, they say they know nothing. Must bring car in, they say. Basically I am screwed and now must spend big bucks to take it the dealer because of Ford's software bug.
Engine light flashing constantly with a vibration. It don't give any codes with the reader.
View 1 RepliesI thought my tranny shift points had gone a little nutty. This afternoon, it suddenly seemed as if it were starting off in 2nd gear...then the OD light started flashing. Now, when you put it in 1st gear manually, or reverse, it's like it's in park. Can't push the truck or anything...put it in drive or 2nd, and it starts off slowly. Once it picks up speed, all seems well. Definitely not starting off in 1st or going into reverse at all. Have y'all seen this problem before?
View 9 RepliesI'm having an issue with my ford again. Escape, V6, 123k miles. Recent work done: Replaced all spark plugs, coils, and intake manifold gaskets. Replaced all four O2 sensors. Oil change switching from the 5w-20 to 5w-30 due to it getting cold, (probably a month ago?).
Now for my current problem. Two days ago on a 20* morning, after it sat outside all night, I drove about 3 miles and then noticed the oil pressure light was blinking intermittently. When I came to a complete stop, it stayed lit. I pulled into a parking lot and starting shutting stuff down. I noticed when I turned the heater blower off, the light went out. Turning it on to High, I noticed the RPMS on the tach dropped to around the 500 mark, and the oil pressure light came back on. I turned it off and let it sit for about 45 minutes. Oil is showing good on the dipstick. I then drove it the last two days without the light coming on.
Now this morning, driving it again in 20* weather, after it sat outside, the light came on again, in almost the exact same place away from home. Both times the motor had reached operating temp, with the temp gauge being in the middle between "C" and "H". This time, even with turning the blower off, it came on every time it was at idle. I let it sit another 45 minutes, but this time when I drove it, the light was more intermittent and then was constant.
Again, the oil level is good on the dipstick, and the motor seems to be running smooth. I'm wondering if this could have anything to do with changing over to a different oil and with it being so cold in the mornings?
I have it written down at home, but I can't remember when I did the actual oil change, but its probably been a little over a month. I went from 5w-20 Pennzoil, to 5w-30; wix filter. I'm planning on doing another oil change tomorrow when I get home and go back to the original 5w-20. Also, I'm ordering a new oil pressure sensor, and I'll try that also. I've also looked into an oil pressure tester....
2008 Escape V6
Got the oil changed at Walmart and they told us there was oil in the air filter and we should replace the pcv valve. Before we changed it the oil pressure light had started coming on when the car is stopped, either in gear or park. Once the gas is hit it goes off, even at something like 1 mph. Well I changed the pcv valve but the oil pressure light is still doing the same thing. What should be my next step?
With winter on its way I have installed winter tires and steel rims w/o pressure sensors on my 08 Escape. Is there a way to disable the dash warning light for low tire air pressure?
View 14 RepliesI just put on new winter tires and rims on my 2012 Escape and after driving about 6 miles, the low tire pressure light came on. Is there is a procedure to learn the vehicle to the new tires?
View 6 RepliesI have a 2001 escape. The red brake warning light in the dash is on. I have changed the low brake fluid sensor and disconnected the parking brake switch . It is not on when first started but comes on shortly after starting to drive (within 100 feet). Do these things have a proportioning valve and a sensor in it?
View 2 RepliesI have error 19 on airbag warning light. I plan to replace RCM and have it programmed to vehicle. Where is RCM located on 2003 Escape, V6?
View 4 RepliesMy Escape is starting to have starting problems. I go to start it and all of the instrument cluster warning lights come on, but the truck doesn't start. If I wait a little while, all of the sudden it starts but all of the sudden the cluster lights start flashing, the various warning beeps sound off, the emergency flashers go off, etc. This lasts anywhere from 5 to 10 minutes until everything resets and goes back to normal. What is causing this?
View 1 RepliesOn my new/used 2008 Escape XLT 2.3L 2WD. It flashes every two seconds, like the manual says. Lower left corner of instrument cluster.
But I don't recall the warning light flashing when I test drove it. But I did push the buttons on the keyfob and various places on the dash/instrument cluster to see what they did...
Is the anti-theft system an on/off affair? If so, how do I turn it off?
I have a 2006 mariner that the ABS light is on all the time and the 4WD light flashes 8 times and the vehicle feels like it is in four wheel drive when turning only at slow speeds and usually in reverse but only when the vehicle has sat for a while, as if you parked for a hour then pulled out of the stall and were turning the wheel.
Tone rings on all wheels are good and all speed sensors have good continuity. Have a friend that works at Ford dealership and he got a tech to scan the car for me. Scan showed the left rear wheel sensor at fault so that's what I'll replace.
I have a Mazda Tribute 2006 2.3. The O/D light would come on, drove it to a friends to scan the check engine light code, and the car almost made it there and then wouldn't remove in reverse, forward, or anything. Turn it off then start it up still wouldn't, then turned it off let it cool and it worked again for a little while.
The code was P0741, just the one code. Took it to a shop to have further tests, they seemed to think it was the clutch was worn and when the fluid heated it lost friction.
Pulled the transmission and thought why not do a Transmission rebuild? I have never done one but there was an awesome video on youtube of the guy doing it so I figured it couldn't be too hard and was just going to try my first rebuild.
According to the guy in the video you always need all new bushing, and we will get a rebuild kit with new clutch packs and the other stuff that comes with those, and sounds like it's a good idea to replace the torque converter.
The car is only at 85K and it looks like the transmission was rebuilt once before he got it at 80K. Maybe a bad rebuild?
Here are some pictures .....
The Input Sprag bearing was shredded and the bushing looks terrible. Can I just replace the bearing and the bushing? Is there any other damage I should be looking for because of this?
The forward planet you can so some eaten metal on the edge and 2 gears spin super smooth and the other 2 you have to push pretty hard to get them to turn. So new forward planet?
The shell's corners look a little rounded I wasn't sure how much was to much, can you tell from the picture if it looks like too much?
Input Sprag
Forward Planet
Sun Gear Shell
This 2002 ford escape 3.0 xlt 4x4. on the dash you have your transmission #s laid out . the #1 seems to always be highlighted in a square. but as you move the shifter to whatever gear you want there is another square that highlights the selected gear. Also, before when you would have it in D it would flash back and forth from D to 2 just the lights not the transmission.
View 1 RepliesSo while driving my mom's 99 passat, after a few miles it gives six loud beeps, the BRAKE light comes on, the oil pressure warning light starts flashing, the ABS light flashes, and the tach sits at zero.
Brakes still work, havent tested ABS. there's no noticeable change in performance. I'm assuming this is the CCM and ABS modules on their last breaths.
No key on prime. Inertia switch OK. Zero line pressure when filter removed & changed. Tries to start with ether. Front 3 coils are for sure firing. Swapped the pump relay with fan relay, no change, no prime.
I'm working with an 03 factory hard copy manual & I'm just not seeing a testing procedure, but I'm bat blind sometimes. What I'm missing? The patient had run fine all day, stopped for an hour. Got back in, started badly, shook somewhat, died, no start since.
The facts: 2009 4x4 V6 Escape with Valve stem mounted TPMS
I am getting a tire pressure sensor malfunction fault. The warning light is on and the error message is displayed on the little screen in the gauge cluster.
What I have tried: First I should say I have replace to defective sensor twice now...
1) I put the escape in tpms train mode by hitting the hazard switch off/on about 6 times.
2) I used the train tool to train all the tires but there is one that is giving me trouble and will not train.
3) I tried deflating the problem tire and inflating it to the specified pressure given on the be pillar of the escape (30 psig)... after inflating it I tried to retain it with no luck.
4) I tried rotating the tires and as I mentioned earlier I have replaces the problem sensor twice. Still can't can't get the problem tire to train.
My thoughts:
1) I don't think this is a module error because I can train the other tires and since I rotated them I know their position is not a factor.
2) its possible that I have got two defective tpms sensors but I think that is unlikely.
3) I have read of another procedure to put the escape in tpms train mode that requires you to turn the ignition on/off, step on the break pedal, tap your head and rub your belly, etc... but I have not tried this method. Is there a difference from this train mode verse hitting the hazard switch on/off about 6 times?
4) Does the train tool only work on previously trained sensors? do I need to register the new TPMS sensor with the TPMS module? I have an OBDII tool that connects to scanXL software on my laptop which included the ford proprietary protocol. I looked for a way to program a tpms sensor (similar to how I did it with my toyota) but couldn't find the option.
I need to replace my pressure line on my 02 Escape 3.0L. Looking for a DIY for doing this same job?
View 1 RepliesMy airbag warning light is flashing 3 , and 4 which i assume is a 34. What this means? I have a 2006 Ford F150...
View 4 Replies