Posted earlier with my escape randomly stalling at idle. Getting a code po446 along with po511. Only stalls at idle after warming up and letting it set a while. When you go to recrank it that is when it won't idle or if it does its at 500 rpms or less. Also after driving it today it smells like rotten eggs. Replaced the idle control valve with no luck. What could cause this?
View 2 RepliesI have a 05 escape hybrid with 75k on it. there is a slight problem every once in a while when it starts the idle jumps up and down and when it is put in reverse it has no power to move. you have to put the pedal to the floor....there are no codes and ford has had the car for a total of three weeks, nothing found and of course it did not act up for them..
View 9 RepliesI test drove 2 2005 escape limited v6 2wd today. Both of them were pretty loud in the cabin at idle. The noise and vibration did lessen after the car started to move. Is this normal for escapes or does this indicate a problem somewhere? Like engine or transmission mounts.
View 2 RepliesWe have a 2005 toyota matrix with 152k miles. In the heat of the afternoon, or after driving 25-30 min the car begins to shutter. Slight hiccups when at speed, then stalls if idling, like at a stop light of the exit ramp. It starts right up, then dies when put in drive. We have taken it to toyota, TWICE. On the second trip, the car died on them and they still found nothing. The check engine light is not on. There are no fault codes. Toyota said replace the spark plugs, which I did. Still has same issue. The ECM was replaced under warranty a couple years ago.
View 2 Replies2004 Ford Escape 2WD 3.0L with about 81,000 miles.
Problem: 2 possibly related
1) If warm up (get to about 190+ degrees) and then cut off engine. Does not start. If I wait about 30 secs and play the gas pedal, then I can get it to start with high revs and after about 15 secs runs normally. Or, I can disconnect the air intake and it'll start fine. But if you stop and try to start again, no joy unless playing with gas pedal.
2) After driving about 20-25 mins, it seems to randomly stall-out while going about 40 mph. When it stalls out, it will restart again after about 30 secs.
Note: Neither of the above throw any codes.
Here's my problem chart after mining the other posts:
Thing to replace/do //// No Code /// Stall while driving /// Won't restart when hot
Fuel Pump //// Yes /// Yes /// Doubt it
Fuel Filter //// Yes /// Yes /// Don't think so
CKP Sensor //// Yes /// Yes /// Yes
CMP Sensor //// Unlikely /// ? /// Possibly
ECT //// Maybe? /// Yes (if too hot) /// Yes
IAC Valve //// Unlikely /// Yes /// No
Thermostat //// Yes /// Yes (if too hot) /// Yes
MAF sensor //// Unlikely /// No /// Yes
What I've done:
- Well, I started looking at the vacuum lines and they were crumbling so I replaced all those (to EGR and all that).
- There is a mystery line that appears to come up from the canister and go to nothing--is this some kind of atmospheric vent?
- My cheap scan tool also shows engine temps getting up to 216 degrees if I make it work (idle high at 2000+ rpm), so I'm suspicious of the cooling system and thinking maybe the ECU is shutting down to avoid overheating.
I'm going to start with flushing the coolant and replacing the ECT and thermostat while doing so. This is relatively inexpensive and ECT can do weird things. The restart problem is consistent, so I'll know if I fixed that right away.
2002 3.0L escape 4WD, stalled twice on me when shifting into reverse after a complete stop. No CEL, truck started right up again....
View 4 RepliesThe car has 130K on the clock, and I don't know if she's had the plugs replaced, but the car has been stalling on her suddenly once it warms up, like the ignition switch is switched off. Then, once it cools down for a night, it runs again. If it only cools down for an hour or two, it will run but only for a few miles before quitting again. I'm thinking a sensor, pcm, or coils, but I'm hoping there's some way to narrow this down a little bit.
View 10 Replies2010 Escape with 74,000 miles. Backstory: This is my daughters car who is away at college about 300 miles away. About a year ago the engine started hesitating when driving and would stall to idle at highway speeds. She took the car in to dealer and they replaced the Throttle body under the CSP that had been issued just prior to the dealer visit. All was fine for about 3 months, then she reports that the car is doing the same thing. Check engine light briefly illuminates and goes right back off when this occurs. She is able to slip the car into neutral and it seems to correct the malfunction. Unfortunately she has gotten so good at this that she keeps her hand on the gearshift when driving. It seems to happen at various speeds with no warning and no lasting effects.
She came to visit for Christmas and I was able to replicate the problem after about 30 minutes of city driving, but not quick enough to take a picture of the wrench that illuminated briefly. I slowed to the edge of the road, put it in park and turned off the key (engine ran the whole time at idle). Cranked back up and good to go! She had the oil changed about a thousand miles ago, I replaced the air filter last night and she had to return to her house for work in the next couple of days. She said it happened 5 times on the way home last night.
Car has always been serviced regularly and was a certified pre-owned when we bought it in March or so of 2012. I also bought the extended warranty although that may be expired by now.
Her local dealer said they can't fix it if the CEL is not on or the problem is not occurring at the exact time they have it in the shop. Now, I am not sure but was under the impression that the computer would record any codes and store them even if the light went off and the car returned to normal.
My 2003 escape stalls from park to reverse and drive,not all the time but when warmed up. IAC motor replaced and still stalls.
View 7 RepliesSo I am changing my transmission fluid tomorrow and was wondering a few things.
1. I noticed some people pull off the transmission hose to the inlet and keep draining that until its clear. For a drain and fill do you do it like that or just pull the plug and refill?
2. When youre filling it back up you just measure how much you taken out and then fill the rest by the dipstick? Anything else i should know?
3. Since I havent changed my transmission fluid in 60,000 miles. I wanted to do a drain and fill. I was thinking I needed to drain and fill it 3 time to catch up to maintenance. How often would you do it to get it clear? Drain and fill then drive it for a week then drain and fill? Or do it all in one day?
I just picked up a 2004 ford escape and information is difficult for me to obtain. Person I purchased from had all new suspension installed. Says it needs new transmission.
My indications: Vehicle starts right up dies/stalls with anything above throttle. Major lack of power. Was able to put in Reverse and it moved a bit and same as drive. Smoke from rear of engine. Seems like coolant dumping into exhaust. shake on exhaust you can hear slosh slosh in exhaust.
No engine trouble codes no lights on dash.
Am I looking at a headgasket? This has the 3.0 duratec v6 with the water pump belt driven by the cam on the driver side. Open up the oil cap there is the timing chain. serpentine belt is on passenger side of engine. There is no coolant/water in the engine oil but the coolant is disappearing FAST. no coolant on spark plugs that indicate its in the cylendars.
Was going to check compression but the compression tester I have only threads up to 14mm. to small for the hole. I can probably rent a tester with proper sizes if needed. Fuel pressure at the rail primes to 60 psi and stays there. Stays at 60 psi while running as well.
I only have one key and 2 FOBs for my 2005 Escape, but I do have the key number (4 digits plus a letter). I understand I need more than one to program another myself. Is there an inexpensive way to obtain/program a backup key?
View 9 RepliesI have the 2.0L 4 cyl. engine (2001 XLS Manual 114k miles). Runs fine when cold but once the engine gets warmed up it starts idling really low. I mean so low that the RPM gauge looks like the engine is turned off, although it hasn't completely stalled (yet). The engine will kind of stumble here and there and occasionally jump up to the normal RPM. Not rough really (in fact it's hard to tell if the engine is on when it's so low) but something is obviously wrong. The check engine light is not on (assume no codes?).
Also when I'm driving I can feel that the RPM's are unstable and erratic. You know, it feels like I'm pushing and releasing the pedal very slightly even though I'm not moving it.
I replaced the spark plugs and fuel filter since they needed to be done anyway. I checked the vacuum lines and they all seem good. I replaced a few deteriorated lines even though they were holding vacuum. None of this changed anything.
So now I'm looking at more expensive stuff like the throttle position sensor, idle air bypass valve, EGR, MAF, etc. Where I should start? Is there anything that I can actually test to see if it's working or do I just need to start replacing parts until I find the problem? I guess cleaning the MAF and IAC might be starting points that don't cost anything (that IAC looks difficult to remove though).
I'm kind of thinking it's the TPS since it feels erratic at speed. However, I have never had a bad TPS cause a slow idle before. I have had it cause rough idle and such but not slow. Can it do that? What about the MAF sensor?
I have a 2001 Escape, V6 engine and I guess it really does not like it when it's cold outside. Usually the car runs just perfect but when the winter arrives and temps drop into the 20s the truck does not want to run idle right when I first start it. I have tried by stating it without touching the gas pedal. And also by pushing it all the way down and then releasing it. I don't know which method is the right one, but it doesn't seem to make a difference. It takes some time and eventually after about 5 miles of driving it will act normal again. What could I do to fix that?
View 9 RepliesI've been having a problem with my car stalling when I brake. It only seems to happen when it's warm outside and I have been running errands and stop for brief periods of time. After about the third stop the car will stall and I have to keep restarting it and keep my foot on the gas. My mechanic seems to think it's the IAC valve. I'm not convinced based on what I've read.
View 7 RepliesI have a 2001 Ford Escape, and when I start it for the first time of the day, it idles really rough, and way below 500RPMs (to the point where it almost stalls). After about 10 minutes, when the car is all warmed up, it runs smoothly, as if there was nothing wrong with it. The only conclusion I can draw is that it is temperature related, but I can't figure out exactly what is causing the issue. This happens on the driest or wettest of days, so moisture doesn't seem to be an issue.
View 2 RepliesI have a 2005 Escape Hybrid. Last summer, the A/C went out, so when in the fall I finally got around to having the cooling system flushed. Did the trick, and A/C works fine. Now that winter's come along, I've noticed an issue with the heat. All fan speeds work correctly, and the dash controls for heat and cold work properly. But what's odd is that I get plenty of heat when the vehicle is at speed, above about 30 mph. As soon as I slow down below that, or hit a red light, there's no heat. The blower just blows cold air until I am back up at speed again.
View 9 RepliesI have a 2005 3.0 front wheel drive Escape that the kids normally drive and recently had a crank over/ no start condition in my driveway. I replaced the fuel pump about three months ago. Turned the key and couldn't hear the fuel pump so I proceeded to check the fuses and relays and everything seemed good. I also checked the inertia switch and it seemed ok as well.
I then checked for power at the harness right above the fuel tank and I had 12 volts on two of the four wires so I assume that I have power to my pump. I then took out the pump and had it replaced it under warranty. So I proceeded to install the new pump and I thought that I would hook the harness back up and just turn on the key for a second to be sure that the new pump is working and there was nothing to be heard. Looking for a wiring diagram/colors of the fuel pump?
2005 Ford Escape XLT (4WD) (non-Hybrid). Our Escape had uneven wear on the front tires. Because the mechanic we've used over the year we've lived here doesn't do alignments, my wife took it to a chain tire place on a Sunday afternoon because they were open. He said the ball joint was bad, so he wouldn't do an alignment and because they were super-busy and short-handed, he asked if we could bring it back during the week for an estimate.
A couple of weeks later I called my guy, who recommended a shop a few blocks over who does alignments, so we took it to him. We told him that the chain store had said about the ball joint. I'm pretty sure that before we took it to him, the car had started occasionally started jerking a bit in a curve, but it's been a couple of months and I only know for certain it was doing it after. (I'm not certain if it was doing it before because my wife was mostly driving that vehicle, then)
The first time it was in his shop, the mechanic said it wasn't the ball joint, but the tie-rod. After fixing that, he sold us a couple of tires and aligned the vehicle. On the way home is when I know I was aware of the car jerking a bit in curves. I'm pretty sure it was jerking in the direction of the curve, but again, it's been a couple of months.
Took it back to him the next day and though we suggested he test drive in one direction which had multiple curves, he said he retightened the tie-rod because one side wasn't right, ran it through alignment again and test drove it in another direction which only had one s-curve.
I want to say it was better for a while, but I can't really swear that to be the case. We've long had an ABS light which our previous mechanic in another part of the country said was the sensor. I had forgotten, but the first mechanic we used here had broken the axle and replaced it at no charge, when he was replacing the alternator.
The alignment mechanic said that we had a bad tone ring and the easiest thing to do would be to replace the axle. A week or so later, I called him and said we were ready to do the brakes, but I have one car and he does many and I wasn't really clear, instead of doing anything with the axle or the tone ring, his shop replaced the brakes.
Somewhere around this time, the vehicle started occasionally jerking to the left. Not in a curve, but in the straightways and the best we can tell, it's mostly when we're accelerating and is most noticeable between 30 & 45 MPH. This may not be entirely true, but it's true enough that we believe it. The "jerk" sort of feels like a car driving through fresh snow "falling" into a rut. It also sort of feels what I imagine a faulty ball joint might feel like.
While it was still more of a minor issue -- it happened more rarely than it's happening now -- we took it to what I'd consider our regular mechanic and got him to replace the axle. I didn't actually say anything to him about the jerking because it was still too occasional and I was hoping it was related to the tone ring. It's now gotten progressively worse and I'm at a loss for diagnosis. You'd think that if it was the ball joint, between the two alignments, the brake job, tire replacement and rotation and getting a new axle, one of the mechanics would have noticed it.
Compounding the issue is the fact that there's two (or three if you count the first guy, four if you count the chain tire place) garages involved. Also, I've done some of the engine work my regular mechanic recommended, so there could be a thing about me getting them to diagnose and then doing the work myself or the one mechanic replacing the axle like the alignment guy had suggested. Who knows. We haven't lived here long, so there's not really a lot of history. All I know is that they all get good Yelp reviews.
Also should probably be factored... the alignment mechanic said he felt vibration around 45 MPH and because didn't think we use the 4WD, he said he disconnected the drive shaft from the CV joint (or something like that) as a means of diagnosis. (If there had been a vibration, we hadn't paid attention to it and he did this at no charge, all on his own) Also, a few years ago, prior to our move, the transmission was rebuilt twice (once under the transmission shop's warranty) and I don't remember what the vehicle was doing, but on a third trip the transmission shop had to do something with the transfer case.
Mostly around 40 MPH -- though it may just be too subtle to notice at higher speeds and we rarely drive this vehicle on the highway, so we're mostly traveling short distances at 35 & 45 MPH -- the SUV lurches a bit toward the left and there's a little jerk in the steering wheel. It really feels like I described, like it's getting caught in a rut. Both the car and the steering wheel jerks to the left side. There hasn't been any noticeable uneven wear over the three months we've been trying to figure this out and the front tires look straight up and down. We also haven't noticed any noise. Not going down the road, not when we turn or when the steering wheel jerks.
2005 Mazda Trib. will not let me shift out of park . It doesn't happen all the time button seems to be sticking . Is it the button or the electrical switch on the brake pedal ? This belongs to a friend of mine and this is the info I'm getting .
View 2 RepliesWhere can I find the key pad code on an 08 escape? I don't have the card in the glove box and I don't want to pay the dealer. It should be printed on the security module box. Where to find it? On my f250 it was under the dash behind radio.
View 14 Replies