Is there a heater core bypass valve under the hood that may be suspect or would a heat transfer door under the dash be the culprit? Engine operating temp seems to be fine.
View 14 RepliesI have an 05 Escape XLT 4WD worth 3.0L V6. My HAYNES says the transfer case lubricant should be checked every 15k - I bought it with 75k and it has 107k now and I have never checked it. I am wondering if it is common practice to do this every 15k? The transfer case is then one next to the oil pan? The book has one photo.
View 1 RepliesI have a 2005 Escape Hybrid. Last summer, the A/C went out, so when in the fall I finally got around to having the cooling system flushed. Did the trick, and A/C works fine. Now that winter's come along, I've noticed an issue with the heat. All fan speeds work correctly, and the dash controls for heat and cold work properly. But what's odd is that I get plenty of heat when the vehicle is at speed, above about 30 mph. As soon as I slow down below that, or hit a red light, there's no heat. The blower just blows cold air until I am back up at speed again.
View 9 RepliesSo I am changing my transmission fluid tomorrow and was wondering a few things.
1. I noticed some people pull off the transmission hose to the inlet and keep draining that until its clear. For a drain and fill do you do it like that or just pull the plug and refill?
2. When youre filling it back up you just measure how much you taken out and then fill the rest by the dipstick? Anything else i should know?
3. Since I havent changed my transmission fluid in 60,000 miles. I wanted to do a drain and fill. I was thinking I needed to drain and fill it 3 time to catch up to maintenance. How often would you do it to get it clear? Drain and fill then drive it for a week then drain and fill? Or do it all in one day?
My wife just picked up the 2015 Escape 3 weeks ago. This is now the 3rd time back to the dealership with it where nothig on the dash is working. No information center, no speedometer, no tach, no fuel gauge, no temp gauge, and even the entire media screen is powerless. So in turn, a lot of the temp controls and radio are gone.
The first time was on a weekend, I pulled the fuse that powers the entire dash to check it, it was fine and upon putting it back in, everything worked. Still had it to the dealer and they couldn't find anything wrong with it. The 2nd time was this past weekend, we decided to leave it so the service team could see what we were talking about. They again, reset the fuse (still wasn't blown), tightened a couple connections, but really couldn't find anything wrong with it.
The 3rd time was just this morning and the vehicle is currently with Ford now. Obviously warrantied, but did their dealership find what the issue was? We really love the Escape, when everything works right.
Can the speedo and tack lights be dimmed to almost off with the + and - buttons either side of the headlight switch on a 2014 Escape?
View 2 RepliesThis 2002 ford escape 3.0 xlt 4x4. on the dash you have your transmission #s laid out . the #1 seems to always be highlighted in a square. but as you move the shifter to whatever gear you want there is another square that highlights the selected gear. Also, before when you would have it in D it would flash back and forth from D to 2 just the lights not the transmission.
View 1 Repliesok this has me stumped I get this buzzing/humming/vibration sound from what seems like around Defroster passenger side but it is not all the time only at higher speeds and it it intermittent . I have removed cabin filter and cleaned filter box and checked for a leaf or something even sealed somewhat the plastic shield that covers the cabin filter. I really don't want to rip dash apart but it is so annoying
View 14 RepliesMy 2003 Escape 2.0L has the "door ajar" light on the dash permanently lit, including with the engine off and key removed, which means that I have to switch the courtesy light on and off by hand or else it stays on.
Obvious first guess is a fault with a door or tailgate switch, but they all look OK to a visual inspection. Are there any multimeter tests I can do? Any specific voltages, resistances to look for?
Started up my 6 cylinder 2005 Ford Escape with 187,000 miles on the engine this morning and after 5 minutes a check engine light came on and the car shut off on its own. I restarted the car and then I got a dash message "Service Emissions" and the car shudders a little when driving. I am going to the autoparts store later for a OBD scanner code check.
View 1 RepliesThe connector is near the floor (that's the gas pedal, in the picture). I've slid back the red clip on both, but the connector still will not separate. Is there a trick?
2001 Escape V6....
I only have one key and 2 FOBs for my 2005 Escape, but I do have the key number (4 digits plus a letter). I understand I need more than one to program another myself. Is there an inexpensive way to obtain/program a backup key?
View 9 RepliesMy transfer case will only pull vacuum to the hubs when floor shifter is in between 4 low and 4 high. as soon as the dash light comes on for low or high it looses vacuum. Is there a switch that tells it to pull vacuum? Any good breakdown of the transfer case?
View 6 RepliesCouple weeks ago, was in a spot that needed 4wd. Turned the switch, the 4x4 dash light came on, but rear wheels didn't do anything. Lucky that we were able to get out with ft wheels only. Has 3.0, xlt version.
View 13 RepliesI have a 2005 3.0 front wheel drive Escape that the kids normally drive and recently had a crank over/ no start condition in my driveway. I replaced the fuel pump about three months ago. Turned the key and couldn't hear the fuel pump so I proceeded to check the fuses and relays and everything seemed good. I also checked the inertia switch and it seemed ok as well.
I then checked for power at the harness right above the fuel tank and I had 12 volts on two of the four wires so I assume that I have power to my pump. I then took out the pump and had it replaced it under warranty. So I proceeded to install the new pump and I thought that I would hook the harness back up and just turn on the key for a second to be sure that the new pump is working and there was nothing to be heard. Looking for a wiring diagram/colors of the fuel pump?
2005 Ford Escape XLT (4WD) (non-Hybrid). Our Escape had uneven wear on the front tires. Because the mechanic we've used over the year we've lived here doesn't do alignments, my wife took it to a chain tire place on a Sunday afternoon because they were open. He said the ball joint was bad, so he wouldn't do an alignment and because they were super-busy and short-handed, he asked if we could bring it back during the week for an estimate.
A couple of weeks later I called my guy, who recommended a shop a few blocks over who does alignments, so we took it to him. We told him that the chain store had said about the ball joint. I'm pretty sure that before we took it to him, the car had started occasionally started jerking a bit in a curve, but it's been a couple of months and I only know for certain it was doing it after. (I'm not certain if it was doing it before because my wife was mostly driving that vehicle, then)
The first time it was in his shop, the mechanic said it wasn't the ball joint, but the tie-rod. After fixing that, he sold us a couple of tires and aligned the vehicle. On the way home is when I know I was aware of the car jerking a bit in curves. I'm pretty sure it was jerking in the direction of the curve, but again, it's been a couple of months.
Took it back to him the next day and though we suggested he test drive in one direction which had multiple curves, he said he retightened the tie-rod because one side wasn't right, ran it through alignment again and test drove it in another direction which only had one s-curve.
I want to say it was better for a while, but I can't really swear that to be the case. We've long had an ABS light which our previous mechanic in another part of the country said was the sensor. I had forgotten, but the first mechanic we used here had broken the axle and replaced it at no charge, when he was replacing the alternator.
The alignment mechanic said that we had a bad tone ring and the easiest thing to do would be to replace the axle. A week or so later, I called him and said we were ready to do the brakes, but I have one car and he does many and I wasn't really clear, instead of doing anything with the axle or the tone ring, his shop replaced the brakes.
Somewhere around this time, the vehicle started occasionally jerking to the left. Not in a curve, but in the straightways and the best we can tell, it's mostly when we're accelerating and is most noticeable between 30 & 45 MPH. This may not be entirely true, but it's true enough that we believe it. The "jerk" sort of feels like a car driving through fresh snow "falling" into a rut. It also sort of feels what I imagine a faulty ball joint might feel like.
While it was still more of a minor issue -- it happened more rarely than it's happening now -- we took it to what I'd consider our regular mechanic and got him to replace the axle. I didn't actually say anything to him about the jerking because it was still too occasional and I was hoping it was related to the tone ring. It's now gotten progressively worse and I'm at a loss for diagnosis. You'd think that if it was the ball joint, between the two alignments, the brake job, tire replacement and rotation and getting a new axle, one of the mechanics would have noticed it.
Compounding the issue is the fact that there's two (or three if you count the first guy, four if you count the chain tire place) garages involved. Also, I've done some of the engine work my regular mechanic recommended, so there could be a thing about me getting them to diagnose and then doing the work myself or the one mechanic replacing the axle like the alignment guy had suggested. Who knows. We haven't lived here long, so there's not really a lot of history. All I know is that they all get good Yelp reviews.
Also should probably be factored... the alignment mechanic said he felt vibration around 45 MPH and because didn't think we use the 4WD, he said he disconnected the drive shaft from the CV joint (or something like that) as a means of diagnosis. (If there had been a vibration, we hadn't paid attention to it and he did this at no charge, all on his own) Also, a few years ago, prior to our move, the transmission was rebuilt twice (once under the transmission shop's warranty) and I don't remember what the vehicle was doing, but on a third trip the transmission shop had to do something with the transfer case.
Mostly around 40 MPH -- though it may just be too subtle to notice at higher speeds and we rarely drive this vehicle on the highway, so we're mostly traveling short distances at 35 & 45 MPH -- the SUV lurches a bit toward the left and there's a little jerk in the steering wheel. It really feels like I described, like it's getting caught in a rut. Both the car and the steering wheel jerks to the left side. There hasn't been any noticeable uneven wear over the three months we've been trying to figure this out and the front tires look straight up and down. We also haven't noticed any noise. Not going down the road, not when we turn or when the steering wheel jerks.
2005 Mazda Trib. will not let me shift out of park . It doesn't happen all the time button seems to be sticking . Is it the button or the electrical switch on the brake pedal ? This belongs to a friend of mine and this is the info I'm getting .
View 2 RepliesI have a 2001 ford escape V6 3.0l. Dropped a new motor in it, got everything running fine. Surprisingly the most frustrating part was when we mixed up the order of the front 3 coils but we got it!
It drove "ok" for a week and a half. Then it started to shudder at 45-55 mph. Got it home that afternoon and started to diagnose why it would shudder. Suspect its not shifting right.We started to diagnose what was wrong, made some adjustments to IAC, MAF and checked a few other things. We then went to test drive, started up fine, drove up the driveway 50' and it died. It didnt sputter and die, it just lost all power and died.
Got it back in the garage and tried to get it started again. Turned Key... nothing. Dash lit up but starter and fuel pump didnt fire. Odometer reads ------. I can jump the starter by pulling the starter relay. Same for the fuel pump. I use a jumper wire between two pins and I can get the starter to crank and the fuel pump runs when I jumper wire the relay too. So I know its not a bad starter nor a bad fuel pump.
Odd part of everything is that It drove just fine that day (other than shuddering). Then started just fine, then died. When it died we were making a sharp left turn in the driveway. We've messed with the steering wheel because it was "accidentally" put upside down when we dropped in the new engine. Could something have grounded out in the steering wheel? Air Bag? Maybe a problem in the clock spring? What would stop it from The fuel, starter and spark all at the same time? Bad PCM? Grounding issues?
I was leaving work in my 05 Escape. Started up fine, made it to the other end of the parking lot and it died. Restarted it and made it about 10 feet and it died again. Now when I try to start it, it just make a single click. Tried getting a jump from a friend and nothing but the same click when trying to start it. Lights are bright (haven't checked batt voltage yet, but will tomorrow).
View 6 RepliesI have a 05 escape hybrid with 75k on it. there is a slight problem every once in a while when it starts the idle jumps up and down and when it is put in reverse it has no power to move. you have to put the pedal to the floor....there are no codes and ford has had the car for a total of three weeks, nothing found and of course it did not act up for them..
View 9 RepliesI recently got an Escape and I am having a issue with the cruise control. That being, it doesn't work. The control module under the hood is all hooked up, the linkage the the throttle body and all. No broken cables.
The brake lights work as intended, and only when the brake is applied. On the inside, the dash-light cruise indicator works fine.
I ran the diagnostic by holding the off button and turning the key on. The cruise light flashes and I begin the sequence. I noticed I was pushing the brake out of habit while running the first few tests. They all returned 2 flashes upon completion of the diagnostic. All other buttons were registered.
Now the strange part, when I took my foot off the brake and did the same test, the final result is three flashes of the cruise light. I understand these flashes represent a fault, and I am having a hard time as I cannot find one.
What do these results mean? I'm thinking the brake being applied gives a fault surrounding the fact that cruise is disabled when the brake is applied.