Ford Escape / Hybrid :: 2005 - Crank Over / No Start
Aug 16, 2016
I have a 2005 3.0 front wheel drive Escape that the kids normally drive and recently had a crank over/ no start condition in my driveway. I replaced the fuel pump about three months ago. Turned the key and couldn't hear the fuel pump so I proceeded to check the fuses and relays and everything seemed good. I also checked the inertia switch and it seemed ok as well.
I then checked for power at the harness right above the fuel tank and I had 12 volts on two of the four wires so I assume that I have power to my pump. I then took out the pump and had it replaced it under warranty. So I proceeded to install the new pump and I thought that I would hook the harness back up and just turn on the key for a second to be sure that the new pump is working and there was nothing to be heard. Looking for a wiring diagram/colors of the fuel pump?
View 2 Replies
Advertisement
I have a 2005 Escape with about 95k miles that won't crank after sitting in the sun on a very warm day. It's intermittent and might be OK for weeks.
This isn't when the engine is hot - it's when the air temperature is in the 80's+ and the black car is parked in the sun. This is the 1st warm weather we've had in several weeks and right on que, it didn't start this afternoon.
The battery is good and there is not voltage to the solenoid when cranking. I've used 2 sets of keys and replaced the PAT sensor ring hoping it was something anti-theft related.
Today, I switched out each under-hood relay (moved them to other locations) and still nada. Luckily today it's DOA in my driveway but may start later.
View 14 Replies
My wife has a 2010 Ford Escape. When we try to start it you have to push the key in REAL hard to get it to crank. It's been doing this for a while and seems to be getting worse. It took her 10 minutes before she could get it to crank earlier today. Our mechanic couldn't find anything wrong the first time we went in.
View 3 Replies
I have a 2003 Ford Escape Limited V6 replaced thermostat and fuel pump and 3 coils and 3 spark plugs recently. Now the theft light has come on and will not crank or start. The fuel pump is still not working unless I manually press the fuse under the hood which is also the only way the car will crank still will not start. That's because the previous owner got the key stuck in the ignition so he bypassed it with a dial you can turn. The dial will put the car into ACC and on mode but will not get the car to crank. Also btn1 and btn2 fuses under the hood are draining my battery.
View 3 Replies
I have a 2007 XLS, 2.3L Auto/AWD. About a month ago it quit running while driving, just shut off. When I tried to restart the dash made clicking noises, fuel pump grunt type noises, cluster stays in drive position even though floor shifter indicates I'm in park. Pulled a code P0606, replaced PCM. It started and ran for 20 minutes, made it about 1/4 mile up the road, shut off again. Now I can't pull a code, dash indicates I'm in drive while vehicle is in park, same noises etc.
View 6 Replies
I have a 05 escape hybrid with 75k on it. there is a slight problem every once in a while when it starts the idle jumps up and down and when it is put in reverse it has no power to move. you have to put the pedal to the floor....there are no codes and ford has had the car for a total of three weeks, nothing found and of course it did not act up for them..
View 9 Replies
So my wife's 2005 escape currently will not start. It was running rough so we brought it in to the shop to have the codes read. There was a bad MAF sensor code so we brought it home and were gonna replace the part the next day. The next day rolls around and it refuses to start. Swapped out the spark plugs which was much needed, replaced the valve cover gasket, which had also gone bad, and put in a new MAF sensor. It still refuses to start. It will turn over, but never starts. Also, the sound as it turns over doesn't sound right. It's hard to explain what sounds off about it, it almost has a "soft" sound to it. I can try to explain better if needed.
View 6 Replies
My "Theft" light on my 2005 Ford Escape is flashing and I cannot start the Escape.
1. I tried the key that I had been using successfully for the last 7 years. , car did not start, Theft light blinked. ,
2. Tried wife's dealer key, Car won't start, theft light blinks.
3. Tried various things, such as manual locking & unlocking, turning alarm beeping on/off, disconnecting battery, etc. Nothing works.
Called the dealer, they say they know nothing. Must bring car in, they say. Basically I am screwed and now must spend big bucks to take it the dealer because of Ford's software bug.
View 9 Replies
Trouble starting our 2008 escape after she has been sitting for atleast 4-5 hours (or more) We can get it going usually but we have to attempt several times before it 'catches'. After running and turning off, it starts no problem. Have replaced mas and didn't work. No 'check engine soon light' so just trying to narrow down the problem. Have replaced the fuel filter and all the spark plugs. Love my escape but not when it doesn't start!!
View 9 Replies
So I am changing my transmission fluid tomorrow and was wondering a few things.
1. I noticed some people pull off the transmission hose to the inlet and keep draining that until its clear. For a drain and fill do you do it like that or just pull the plug and refill?
2. When youre filling it back up you just measure how much you taken out and then fill the rest by the dipstick? Anything else i should know?
3. Since I havent changed my transmission fluid in 60,000 miles. I wanted to do a drain and fill. I was thinking I needed to drain and fill it 3 time to catch up to maintenance. How often would you do it to get it clear? Drain and fill then drive it for a week then drain and fill? Or do it all in one day?
View 4 Replies
About a block and a half from the house, it died while driving. Had heard some noise coming from rear drivers side maybe 20 minutes prior, and assumed it was the fuel pump.
So, I have put a new fuel pump, filter, and relay. Will crank, but not turn over. Next step was carburetor fluid in throttle while starting, still wouldn't turn over.
2001 Escape 6 cyl...
View 5 Replies
I only have one key and 2 FOBs for my 2005 Escape, but I do have the key number (4 digits plus a letter). I understand I need more than one to program another myself. Is there an inexpensive way to obtain/program a backup key?
View 9 Replies
I have a 2005 Escape Hybrid. Last summer, the A/C went out, so when in the fall I finally got around to having the cooling system flushed. Did the trick, and A/C works fine. Now that winter's come along, I've noticed an issue with the heat. All fan speeds work correctly, and the dash controls for heat and cold work properly. But what's odd is that I get plenty of heat when the vehicle is at speed, above about 30 mph. As soon as I slow down below that, or hit a red light, there's no heat. The blower just blows cold air until I am back up at speed again.
View 9 Replies
2005 Ford Escape XLT (4WD) (non-Hybrid). Our Escape had uneven wear on the front tires. Because the mechanic we've used over the year we've lived here doesn't do alignments, my wife took it to a chain tire place on a Sunday afternoon because they were open. He said the ball joint was bad, so he wouldn't do an alignment and because they were super-busy and short-handed, he asked if we could bring it back during the week for an estimate.
A couple of weeks later I called my guy, who recommended a shop a few blocks over who does alignments, so we took it to him. We told him that the chain store had said about the ball joint. I'm pretty sure that before we took it to him, the car had started occasionally started jerking a bit in a curve, but it's been a couple of months and I only know for certain it was doing it after. (I'm not certain if it was doing it before because my wife was mostly driving that vehicle, then)
The first time it was in his shop, the mechanic said it wasn't the ball joint, but the tie-rod. After fixing that, he sold us a couple of tires and aligned the vehicle. On the way home is when I know I was aware of the car jerking a bit in curves. I'm pretty sure it was jerking in the direction of the curve, but again, it's been a couple of months.
Took it back to him the next day and though we suggested he test drive in one direction which had multiple curves, he said he retightened the tie-rod because one side wasn't right, ran it through alignment again and test drove it in another direction which only had one s-curve.
I want to say it was better for a while, but I can't really swear that to be the case. We've long had an ABS light which our previous mechanic in another part of the country said was the sensor. I had forgotten, but the first mechanic we used here had broken the axle and replaced it at no charge, when he was replacing the alternator.
The alignment mechanic said that we had a bad tone ring and the easiest thing to do would be to replace the axle. A week or so later, I called him and said we were ready to do the brakes, but I have one car and he does many and I wasn't really clear, instead of doing anything with the axle or the tone ring, his shop replaced the brakes.
Somewhere around this time, the vehicle started occasionally jerking to the left. Not in a curve, but in the straightways and the best we can tell, it's mostly when we're accelerating and is most noticeable between 30 & 45 MPH. This may not be entirely true, but it's true enough that we believe it. The "jerk" sort of feels like a car driving through fresh snow "falling" into a rut. It also sort of feels what I imagine a faulty ball joint might feel like.
While it was still more of a minor issue -- it happened more rarely than it's happening now -- we took it to what I'd consider our regular mechanic and got him to replace the axle. I didn't actually say anything to him about the jerking because it was still too occasional and I was hoping it was related to the tone ring. It's now gotten progressively worse and I'm at a loss for diagnosis. You'd think that if it was the ball joint, between the two alignments, the brake job, tire replacement and rotation and getting a new axle, one of the mechanics would have noticed it.
Compounding the issue is the fact that there's two (or three if you count the first guy, four if you count the chain tire place) garages involved. Also, I've done some of the engine work my regular mechanic recommended, so there could be a thing about me getting them to diagnose and then doing the work myself or the one mechanic replacing the axle like the alignment guy had suggested. Who knows. We haven't lived here long, so there's not really a lot of history. All I know is that they all get good Yelp reviews.
Also should probably be factored... the alignment mechanic said he felt vibration around 45 MPH and because didn't think we use the 4WD, he said he disconnected the drive shaft from the CV joint (or something like that) as a means of diagnosis. (If there had been a vibration, we hadn't paid attention to it and he did this at no charge, all on his own) Also, a few years ago, prior to our move, the transmission was rebuilt twice (once under the transmission shop's warranty) and I don't remember what the vehicle was doing, but on a third trip the transmission shop had to do something with the transfer case.
Mostly around 40 MPH -- though it may just be too subtle to notice at higher speeds and we rarely drive this vehicle on the highway, so we're mostly traveling short distances at 35 & 45 MPH -- the SUV lurches a bit toward the left and there's a little jerk in the steering wheel. It really feels like I described, like it's getting caught in a rut. Both the car and the steering wheel jerks to the left side. There hasn't been any noticeable uneven wear over the three months we've been trying to figure this out and the front tires look straight up and down. We also haven't noticed any noise. Not going down the road, not when we turn or when the steering wheel jerks.
View 14 Replies
2005 Mazda Trib. will not let me shift out of park . It doesn't happen all the time button seems to be sticking . Is it the button or the electrical switch on the brake pedal ? This belongs to a friend of mine and this is the info I'm getting .
View 2 Replies
I was leaving work in my 05 Escape. Started up fine, made it to the other end of the parking lot and it died. Restarted it and made it about 10 feet and it died again. Now when I try to start it, it just make a single click. Tried getting a jump from a friend and nothing but the same click when trying to start it. Lights are bright (haven't checked batt voltage yet, but will tomorrow).
View 6 Replies
Is there a heater core bypass valve under the hood that may be suspect or would a heat transfer door under the dash be the culprit? Engine operating temp seems to be fine.
View 14 Replies
I recently got an Escape and I am having a issue with the cruise control. That being, it doesn't work. The control module under the hood is all hooked up, the linkage the the throttle body and all. No broken cables.
The brake lights work as intended, and only when the brake is applied. On the inside, the dash-light cruise indicator works fine.
I ran the diagnostic by holding the off button and turning the key on. The cruise light flashes and I begin the sequence. I noticed I was pushing the brake out of habit while running the first few tests. They all returned 2 flashes upon completion of the diagnostic. All other buttons were registered.
Now the strange part, when I took my foot off the brake and did the same test, the final result is three flashes of the cruise light. I understand these flashes represent a fault, and I am having a hard time as I cannot find one.
What do these results mean? I'm thinking the brake being applied gives a fault surrounding the fact that cruise is disabled when the brake is applied.
View 3 Replies
The factory installed passive anti theft alarm keeps going off without external cause. Went to dealership to have them do the scan and all alarms point to the right rear-door. They suggest replacing the latch. This same latch was replaced 13 months ago for same problem. They will not honor the now out of date 12 month replacement warranty. They said they have checked the wiring and all looks OK. Must be the latch. I only have 30,000 miles on the vehicle and this is a rarely used door, yet I have to replace the same latch again?? Can the door ajar module be replaced separately and would it be less expensive to do so?
View 14 Replies
A friend has 2005 escape 3l. He called me yesterday saying that he needed replacing his fuel pump.
Before I got to his place he had already replaced the fuel filter...
We got the pump replaced, and when we went to start the vehicle, it still wouldn't start.
We double checked to make sure everything was connected and plugged in and it was. We checked all fuses, and they were all good.
This morning I am going to try jumping the relay and see if that does anything. What else to check?
View 3 Replies
I have a 2005 Ford Escape XLT 3.0L V6 which I bought 6 weeks ago. It has 103,000 miles on the clock. I mainly use it for going to school and getting around town etc but on Sunday I had to take my parents back. It's a round trip of 230 miles. Weather was sunny. Traffic on the Expressway so a lot of slowing down, stopping, setting off cycles but no issues. On the way home, about two toll plazas from my exit on the I90, I noticed that the engine sounded and felt like I was driving in a higher gear than that required for the speed I was doing (5 mph). It's an automatic (which I'm not used to as I've always driven manual) so I don't make any gear changes but if I'd been in a manual, it felt like I was in 2nd when I should have been in 1st. Does that make sense?
Anyhow, so I managed not to stall at the toll plazas but when I exited, the engine stalled 3 times (twice at intersections and finally when I pulled up outside my house). There is no problem starting the car after this has happened. I called my local autoshop who said to bring it in Tuesday so I didn't drive it Monday. Tuesday morning, it felt exactly the same when I was slowing down for traffic, intersections, turnings etc. The autoshop had it 3 days and couldn't find anything wrong with it. There is no data stored on the computer to show any of this happened and it has driven fine for them when they've taken it out. Beyond frustrated! I know what I heard and felt. Someone mentioned the overdrive staying on but I don't know what that means.
View 3 Replies
